522339
5
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
valve seat in the bore for the intake check valve assembly. It too should be installed with the
beveled edge of the valve seat facing outward, or against your finger.
3. With the o-ring side facing down (facing the valve seat), lower one of the poppet valves (they are
both identical) into the bore for the reject check valve assembly. The poppet valve should be level
and in the center of the valve seat at the bottom of the bore, with the narrow stem facing up.
Lower a new valve spring over the stem of the poppet valve. Next, lower a valve retainer into the
bore. Note that one side of the retainer has a
circular groove that must engage the end of the
valve spring. Finally, replace the o-ring on the
outlet adaptor and screw the adaptor into the
reject check valve bore and tighten. The tube
fitting should still be installed in the outlet
adaptor. If not, install and tighten. Be careful not
to damage the o-ring on the tube fitting. This o-
ring is not included in the RSK. Test your
installation by inserting a small screwdriver into
the hole for the reject check valve on the side of
the check valve plate opposite the tube fitting.
The reject poppet valve should move up and
down freely.
4. Refer again to Figure R-3. Working from the other side of the check valve plate, use the same
procedure to assemble the intake poppet valve, valve spring and valve retainer. After testing the
action of the intake check valve, install the plastic intake hose barb.
5. Lubricate a new o-ring (8012532) with silicon grease and install it into its groove in the pump
side of the check valve plate. Taking care that the intake check valve components do not fall out of
their bore, bring the check valve plate and the pump body together, align them, and install the six
sockethead flange bolts to hold the assembly together. Tighten these fasteners snugly. (If a torque
wrench is available, tighten to approximately 120140 in.-lbs.) See Figure R-6.
6. Lubricate the inside of the cylinder in the pump body with silicon grease. Insert the piston
assembly through its hole in the pump back plate and slide it as far as it will go toward the pump
back plate, as shown in Figure R-7. Install the two o-rings (8012830) and (8012444) in their
grooves in the pump back plate. Make
sure the relief valve spring is installed in
the pump body. Bring the pump back
plate and pump body together
carefully, first guiding the piston into the
cylinder in the pump body, and then
pressing the back plate as close as
possible to the pump body. Install the
four sockethead flange bolts and tighten
snugly (approximately 120140 in.-
lbs.).
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Humminbird 777c2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Humminbird 777c2 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info