Handleiding Hotpoint-Ariston LFF 8M113 7 (pagina 13 van 72) (Duits, Engels, Spaans, Pools, Turks)

593394

Verklein

Vergroot

Pagina terug

1/72

Pagina verder

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table/industrial salt or washing-up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

any rinse aid. However, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard.

(Follow the instructions given on the packaging).

If you do not add salt or rinse aid, the LOW SALT* and

LOW RINSE AID indicator lights will stay lit.

Measuring out the rinse aid

Rinseaidmakesiteasierforthecrockerytodry,aswaterrunsoff

the surfaces more readily and therefore does not leave streaks

or marks. The rinse aid dispenser should be filled:

• WhentheLOWRINSEAIDindicatorlight* on the control panel

is illuminated, a reserve supply of rinse aid is still available

for1-2cycles;

1. Open the dispenser “D” by pressing and pulling up the tab

on the lid;

2.Carefully introduce the rinseaidasfar as the maximum

reference notch of the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

Rinse-aid dispenser setting

If you are not completely satisfied with the drying results, you

canadjustthequantityofrinseaid.Switchonthedishwasher

usingtheON/OFFbutton,waitafewsecondsandswitchitoff

usingtheON/OFFbutton.

PresstheStart/Pausebutton 3 times;switchonthemachine

usingtheON/OFFbuttonandaccesstheadjustmentmenu-the

rinse-aid indicator light is lit

(

set to factory level).

Select the level of rinse aid supply using the ECO cycle button

(0to4max.)

Press the ON/OFF button to save the setting.

IftherinseaidlevelissettoZERO,norinseaidwillbesupplied.

TheLOWRINSEAIDindicatorlightwillnotilluminateifyourun

out of rinse aid.

• Iftherearestreaksonthecrockery,settheadjustmentdevice

toalowernumber(1-2.)

• Ifthereare drops ofwateror limescale marks, setthe

adjustment device to a higher number (3-4.)

Setting the water hardness

Everydishwasherisequippedwithawatersoftenerwhich,by

using refined salt specially designed for this type of appliance,

supplies water without limescale which is then used to wash

the crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the

water hardness level in your area. This information can be

obtained from the organisation which supplies your household

with water.

-Switchon the dishwasherusingtheON/OFFbutton,wait a

fewsecondsandswitchitoffusingtheON/OFFbutton.Hold

downtheStart/Pausebuttonformin.3seconds;switchonthe

machineusingtheON/OFFbuttonandaccesstheadjustment

menu - the salt indicator light is lit.

- Select the desired level (1 to 5* max. based on the dishwasher

model) using the ECO button.

(water softener set to medium level).

Press the ON/OFF button to save the setting.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH=hardnessmeasuredinGermandegrees-°f=hardness

measuredinFrenchdegrees–mmol/l=millimolesperlitre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,

make sure that the salt dispenser is never empty.

Refinedsaltremoveslimescalefromthewater,thusavoiding

the formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(see Description)

and should be filled:

• Whenthegreenfloat* cannot be seen by simply looking at

the cap of the salt dispenser;

• WhentheLOWRINSEAIDindicatorlightonthecontrolpanel

is illuminated *;

1.Removethelowerrackandunscrewthe

cap (anticlockwise).

2.Thefirsttimeyoudothis:fillthewater

tank right up to its edge.

3. Position the funnel

(see figure)

and

fill the salt dispenser up to the edge

(approximately 1 kg). It is normal for a little

water to leak out.

4.Removethefunnel*andwipeanysaltresiduesawayfrom

the opening; rinse the cap under running water and then screw

it on, the head facing downwards so as to let the water flow out

of the four slots (star-shaped arrangement) in the lower part of

the cap (cap with green float

*).

It is advisable to perform this procedure every time you add

salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair).

Whennecessary,measureoutthesaltbeforeawashcycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

* Only available in selected models.

Water Hardness Table

Average salt dispenser

capacity duration

level °dH °fH mmol/l months

1 0 - 6 0 - 10 0 - 1 7 months

2 6 - 11 11 - 20 1,1 - 2 5 months

3 12 - 17 21 - 30 2,1 - 3 3 months

4 17 - 34 31 - 60 3,1 - 6 2 months

34 - 50 61 - 90 6,1 - 9 2/3 weeks

For values between 0°f and 10°f, we do not recommend the use of salt.

* a setting of 5 may increase cycle duration.

** 1 wash cycle per day.

Hotpoint-Ariston LFF 8M113 7 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info