If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off.
Programme operations
When a programme is running the relevant
indicator light will remain on and the 3
“PROGRAMME STATUS” indicator lights
("WASH" , "RINSE" , and "DRY" )
will light singularly and in sequence to
indicate the current phase.
Programme end
A5 second alarm will sound (if not muted)
3 times at 30 second intervals to signal that
the programme has ended.
The “PROGRAMME STATUS” indicator
lights will turn off and the indicator light
which is factory set "recommended”, or
the indicator light for the Auto’ Memory
programme, will start to flash.
Dishes can now be removed and the
dishwasher turned off by pressing the
"ON/OFF" button or dishes can be loaded
for new cycle.
Option button
"HALF LOAD" button
By using this option, it is possible to wash
a smaller quantity of crockery: you should
load only the upper basket for dishes and
place cutlery in the tray in the bottom
basket.
This reduces water and energy consumption
and requires a smaller quantity of
detergent.
23
22
"DELAY START" button
The dishwasher start time can be set with
this button, delaying the start by 3, 6 or 9
hours.
Proceed as follows to set a delayed start:
■ Press the "DELAY START" button (each
time the button is pressed the start
will be delayed by 3, 6 or 9 hours
respectively and the corresponding time
indicator light will illuminate).
■ To start the countdown, press the selected
programme button (the relevant indicator
light will come on, while the set time
indicator light will start to flash).
If a 9 hour delay is set, countdown will be
displayed by the 6h indicator light after 3
hours and the 3h indicator light after 6
hours.
At the end of the last 3 hours (at the end
of countdown) the 3h indicator light will
stop flashing and remain on to indicate the
washing phase and the programme will
start automatically.
If countdown has not ended, whereby
the programme has not yet started, it is
possible to change or cancel the delayed
start and select another programme or to
select/deselect the option button, proceeding
as follows:
■ Hold down the selected programme
button for at least 5 seconds. The
programme indicator lights (except for
the "RAPID" programme indicator light)
will flash.
■ The selected programme will be cancelled
and the indicator light for the
"recommended" programme or the
indicator light for the programme that
was used at least 3 times consecutively
will start to flash.
■ Press the "DELAY START" button to
set another delayed start time (the
corresponding indicator light will turn on).
■ A new programme can be set after a
delayed time has been changed or
cancelled or an option button has selected
or deselected.
Alarm mute
The alarm for the programme end may
be muted as follows:
■ With the dishwasher off, hold down the
"HALF LOAD" button for few seconds
while simultaneously pushing the
"ON/OFF" button, releasing them only
after the alarm sound.
■ Press the "HALF LOAD" button again:
the relevant indicator light (turned on to
indicate that the alarm is activated) will
flash (to indicate that the alarm is off).
■ Wait for the alarm to sound to indicate
that the settings were saved.
■ To turn the alarm on again, follow the
same procedure.
Fault signals
If malfunctions or faults occur when a
programme is running the indicator light
that corresponds to the selected cycle
(2 indicator lights for the "COLD RINSE"
programme) will flash rapidly and the alarm
sounds.
In this event, turn the dishwasher off by
pressing the "ON/OFF" button. After
checking to make sure the water inlet hose
tap is open, that the drain hose is not bent
and that the siphon or filters are not
clogged, set the selected programme
again. If the anomaly persists, contact
Customer Service Department.
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically discharge any excess
water should a problem occur.
WARNING!
To ensure the correct operation of
the anti-overflow safety device, we
recommend that the dishwasher is
not moved or tilted during operation.
If however it is necessary to tilt or
move the dishwasher, please ensure
that the washing cycle is complete
and that there is no remaining water
inside the dishwasher.
