Handleiding Hoonved C 43 (pagina 14 van 19) (Engels)

637642

Verklein

Vergroot

Pagina terug

1/19

Pagina verder

4. Press the button (1) to automatically begin filling the

washing tank. Light (4) will come on once the level has

been reached. The water inside the boiler (see light 6)

and the water in the washing tank will automatically

start heating.

5. Open the door and pour the quantity of detergent

indicated by the manufacturer directly into the tub. This

operation need not be carried out when the machine is

equipped with the optional dispenser.

6. After warning light (6) has gone out, wait about 20

minutes to allow the water in the washing tub to reach

the programmed operating temperature.

3.3.b Washing operation (Figs 9-10)

1. Load the dirty crockery into the basket according to the

configuration of the machine.

2. Open the door and fit the basket into the tub, then shut

the door again.

3. Press “START” button (3). Light (5) will come on to

indicate that the cycle has started.

4. Light (5) will go out to indicate that the cycle has

terminated. Now open the door and remove the basket.

5. Add a spoonful of detergent after every 5/6 washes.

This operation need not be carried out if the machine

is equipped with the optional dispenser.

The doses are indicative and not binding since they

vary according to the hardness of the water and utilized

type of detergent.

Cold rinse - Optional - (only for C 35 -SPB 35 Mod.)

The coolthe glasses, at the end of the cycle, press for a few

seconds the cold rinse button (7) Fig. 1/9.

IMPORTANT

The hot water supply (50°÷60°C) does not allow a manual

cold rinse to be obtained.

IMPORTANT

Keep the tub door closed between one cycle and the next

to prevent the water in the tub from cooling.

ATTENTION

Door opening during the cycle will block machine operation

in the same way as an EMERGENCY device.

To interrupt the cycle, open the tub door in the following

way:

• Slightly open the tub door. Wait a few seconds for the

water pressure in the rods to drop, then completely

open the door.

• This operation is very important since it prevents the

operator from being wetted or scalded as during the

rinsing phase, the water reaches a temperature of

90°C.

• Close the door and the cycle will continue from where

it was interrupted.

3.3.c Changing the water (Fig. 10)

This operation must be carried out after every 10 cycles or

so, depending on the amount of accumulated dirt.

1. Switch off the machine as indicated in paragraph 3.3.d,

then lift the overflow (21) and allow the tub to completely

drain.

2. Fit the overflow (21) back into its housing and repeat

the machine preparation operations as indicated in

paragraph 3.3.a.

3.3.d Daily regenerating operations (for mod. CD-

CRD-SPD-SPRD only)(Fig. 10)

The regenerating operations must be carried out once

work has terminated.

1. Remove the overflow (21) and reset the line button (1).

2. Keep button (2) depressed for a few seconds. Warning

light (5) will come on to indicate the beginning of the

regenerating cycle, which lasts about 20 minutes.

ATTENTION

Remember to keep the door closed during the

regenerating phase.

3.3.e Manual drain (Fig. 1)

(on machine with drain pump only)

To manually empty the water from the tub, switch off the

line button (1) Fig. 1 and push the START/DRAIN button

(3).

3.3.f Switch-off (Fig. 9)

At the end of the work day, set the line switch (1) to position

“0” OFF, disconnect the main switch installed prior to the

machine and turn off the water delivery cock.

ATTENTION

Disconnect the main circuit-breaker prior to the machine

and turn off the water delivery cocks if the dishwasher is

faulty or operates badly.

Only allow technicians from the manufacturer’s authorized

after-sales service center to make repairs.

4. CLEANING (Fig. 10)

4.1 General information

Strict compliance with the maintenance instructions in this

section will keep your machine in a good working condition

and will notably reduce the need for repairs.

ATTENTION

If any machine component becomes faulty, FIRST CHECK

that all the instructions given in the previous paragraphs

have been complied with during use.

Repairs must be carried out immediately, as soon as the

fault occurs. This will prevent the trouble from becoming

worse and damaging other parts.

ENGLISH

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Hoonved C 43 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Hoonved C 43

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info