Handleiding Honeywell HZ-3200 Series (pagina 1 van 8) (Engels)

527127

Verklein

Vergroot

Pagina terug

1/8

Pagina verder

TOWER SURROUND HEATERS

Model HZ-2200 Series

Model HZ-3200 Series

Model HZ-3220 Series

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, basic

precautions should always be followed to

reduce the risk of fire, electric shock, and

injury to persons, including the following:

1. Read all instructions before using this heater.

2. This heater is hot when in use. To avoid burns,

do not let bare skin touch hot surfaces. If

provided, use handle when moving this heater.

Keep combustible materials, such as furniture,

pillows, bedding, papers, clothes, and curtains at

least 3 feet (0.9 m) from the front of the heater

and keep them away from the sides and rear.

3. Extreme caution is necessary when any heater is

used by or near children, pets or invalids and

whenever the heater is left operating and

unattended.

4. Always unplug heater when not in use.

5. Do not operate any heater with a damaged cord

or plug or after the heater malfunctions, has been

dropped or damaged in any manner.

6. Do not use outdoors.

7. This heater is rated at 1500W, 120 VAC. It is

intended for use on tabletops, desktops and

floors. It is not to be used in wet or moist

locations, such as bathrooms and laundry areas.

If an extension cord must be used, it must be 14

gauge or larger and rated no less than 1875

watts.

8. Do not run cord under carpeting. Do not

cover cord with throw rugs, runners, or the like.

Arrange cord away from traffic area where it will

not be tripped over.

9. This appliance has a polarized plug (one blade is

wider than the other). To reduce the risk of shock,

this plug is intended to fit only one way in a

polarized outlet. If the plug does not fit securely

in the outlet, reverse the plug. If it still does not

fit, contact a qualified electrician. DO NOT

attempt to defeat this safety feature.

10. This heater draws 12.5 amps during operation

when in the high setting. To prevent overloading

a circuit, do not plug the heater into a circuit that

already has other appliances working.

11. It is normal for the plug to feel warm to the touch;

however, a loose fit between the AC outlet

(receptacle) and plug may cause overheating and

distortion of the plug. Contact a qualified

electrician to replace loose or worn outlet.

12. To disconnect the heater, first turn controls to the

OFF position, then grip the plug and pull it from

the wall outlet. Never pull by the cord.

13. Do not insert or allow foreign objects to enter any

ventilation or exhaust opening as this may cause

an electric shock or fire, or damage the heater.

14. To prevent a possible fire, do not block air intakes

or exhaust in any manner. Do not use on soft

surfaces, like a bed, where openings may

become blocked.

15. A heater has hot and arcing or sparking parts

inside. Do not use it in the areas where gasoline,

paint, or flammable liquids are used or stored.

16. Use this heater only as described in this manual.

Any other use not recommended by the

manufacturer may cause fire, electric shock, or

injury to persons.

17. The output of this heater may vary and its

temperature may become intense enough to burn

exposed skin. Use of this heater is not

recommended for persons with reduced

sensitivity to heat or an inability to react to avoid

burns.

18.

SAVE THESE

INSTRUCTIONS

The Honeywell trademark is used by Kaz, Inc. under license from Honeywell Intellectual Properties, Inc.

HZ-2200-3200-3220_OM_Rev1.qx 6/8/05 1:19 PM Page 1

HZ-2200-3200-3220_OM_Rev1.qx 6/8/05 1:19 PM Page 2

• Place the heater on a firm, level, open surface free from obstructions and at least 3 feet (0.9m) away

from any wall or any combustible material. DO NOT use on an unstable surface such as bedding or

deep carpeting. BE SURE THE HEATER IS NOT IN A POSITION WHERE IT MAY BE TRIPPED OVER BY

CHILDREN OR PETS.

SET-UP

HZ-2200 OPERATION

• Place the heater on a firm, level, open surface free from obstructions and at least 3 feet (0.9m) away

from any wall or any combustible material. DO NOT use on an unstable surface such as bedding or

deep carpeting. BE SURE THE HEATER IS NOT IN A POSITION WHERE

IT MAY BE TRIPPED OVER BY CHILDREN OR PETS.

• The Tower Surround Heater is designed to disperse heat in either a

360° range or in one direction only. To select the desired heating mode,

slide the Direction Control switch, located on the top of the heater, to

the position of your choice (Fig. 2):

– to the left ( ) for 360

Heating

– to the right ( ) for Forward Only Heating (One Direction Heating)

• With the Power knob in the OFF position, plug the heater into a

polarized 120V outlet. DO NOT FORCE THE POLARIZED PLUG INTO THE

OUTLET; it will only fit one way.

• Turn the Thermostat control fully clockwise to the HIGH setting.

• This heater is equipped with three (3) settings: High, Low and Fan Only.

The High setting uses 1500 watts of power and the Low setting uses

750 watts of power. You can select the proper setting to accommodate

your comfort level. Because the Low setting does not require as much

electricity to operate, it is more energy efficient and may be a better

option if you are concerned about the amperage draw on a circuit when the heater is in the High

setting.

• Turn the heater on using the Child Resistant Switch (Power knob). To operate the switch, push in the

two sides of the Power knob while turning it clockwise to the desired position (Fig. 3). The power light

will illuminate. The Child Resistant Switch helps to keep the heater from being turned on

unintentionally; there is no way to disengage this safety feature.

• When the room reaches a comfortable temperature, slowly turn the Thermostat control counter-

clockwise until the heating element goes off (the power light will remain on). This is the point at which

the Thermostat setting equals the room temperature. At this setting, the Thermostat will automatically

turn the heater on and off to maintain the selected temperature.

• Push down and turn the Power knob to OFF and unplug the heater when you are finished using it.

ASSEMBLY

(HZ-3200 & HZ-3220 SERIES)

• Remove the Handle from the box, it may be nested in the styrofoam packing

material.

• Place the heater on a firm, level floor.

• Line up the prongs on the bottom of the handle with the openings on the top

of the heater and firmly push down (Fig. 1). The handle is now permanently

fastened to the top cover.

NOTE: The HZ-2200 Series does not require any assembly.

Fig. 1

Fig. 3

Forward Only

Heating

(One Direction

Heating)

360° Heating

Fig. 2

HZ-2200-3200-3220_OM_Rev1.qx 6/8/05 1:19 PM Page 3

HZ-3200 OPERATION

• The Tower Surround Heater is designed to disperse heat in either a

360° range or in one direction only. To select the desired heating mode,

slide the Direction Control switch, located on the top of the heater, to

the position of your choice (Fig. 4):

– to the left ( ) for 360

Heating

– to the right ( ) for Forward Only Heating (One Direction Heating)

• With the Power knob in the OFF (O) position, plug the heater into a

polarized 120V outlet. DO NOT FORCE THE POLARIZED PLUG INTO THE

OUTLET; it will only fit one way.

• Turn the Thermostat control fully clockwise to the HIGH setting.

• This heater is equipped with three different heat settings. The

Low setting ( ) uses 600 watts of power, the Medium setting ( )

uses 900 watts of power and the High setting ( ) uses 1500

watts of power. You can select the proper setting to accommodate

your comfort level. Because the Low and Medium heat settings do

not require as much electricity to operate, they are more energy

efficient and may be better options if you are concerned about the

amperage draw on a circuit when the heater is in the High setting.

• Turn the heater on using the Child Resistant Switch (Power knob).

To operate the switch, push in the two sides of the Power knob while turning it clockwise to the

desired position (Fig. 5). The power light will illuminate. The Child Resistant Switch helps to keep the

heater from being turned on unintentionally; there is no way to disengage this safety feature.

• When the room reaches a comfortable temperature, slowly turn the Thermostat control counter-

clockwise until the heating element goes off (the power light will remain on). This is the point at which

the Thermostat setting equals the room temperature. At this setting, the Thermostat will automatically

turn the heater on and off to maintain the selected temperature.

• Push down and turn the Power knob to OFF and unplug the heater when you are finished using it.

Fig. 5

HZ-3220 OPERATION

• The Tower Surround Heater is designed to disperse heat in either a 360°

range or in one direction only. To select the desired heating mode, slide

the Direction Control switch, located on the top of the heater, to the

position of your choice (Fig. 6):

– to the left ( ) for 360

Heating

– to the right ( ) for Forward Only Heating (One Direction Heating)

• Plug the heater into a polarized 120V outlet. DO NOT FORCE THE

POLARIZED PLUG INTO THE OUTLET; it will only fit one way.

STEP 1: POWER

• Press the Power button to start the heater. Your heater will automatically start on High power ( ),

continuous run (Fig. 7).

• To turn your heater OFF simply press the Power button again.

NOTE: When initially turned on, the heater will operate in continuous run mode. The heater will

continue to run regardless of the room temperature in this mode. The heater is running in this mode

when no LED lights are illuminated on the thermostat display.

Forward Only

Heating

(One Direction

Heating)

360° Heating

Fig. 4

Forward Only

Heating

(One Direction

Heating)

360° Heating

Fig. 6

Power

Knob

Thermostat

Knob

Power

Light

HZ-2200-3200-3220_OM_Rev1.qx 6/8/05 1:19 PM Page 4

STEP 2: HEAT OUTPUT

Your unit has three output levels

HIGH: 1500 Watt Heating

MED: 900 Watt Heating

LOW: 600 Watt Heating

• Push the up button (+) to increase output level and push the down

button (–) to decrease output level. The LED's will illuminate to

reflect which output level you have selected (Fig. 8).

STEP 3: SET THERMOSTAT

• Adjust your thermostat anywhere between 60

F (15

C) and

F (27

C).

• Push the up button (+) to increase the desired temperature and

push the down button (–) to decrease the desired temperature

level. The LED's will illuminate to reflect the temperature you have

selected (Fig. 9).

For example: If you set your thermostat at 65

F (18

C), the 60

(15

C) and 65

F (18

C) LED’s will be illuminated.

• Once you have set your desired temperature, the unit will operate

under this desired setting until the unit is turned off.

• When the desired temperature has been reached, the unit will

automatically shut off. (The thermostat LED's will remain

illuminated)

• Your unit will turn back on when the current room temperature

decreases below your desired temperature.

STEP 4: CHILD-LOCK FEATURE

• This heater is equipped with a child-lock feature. This feature will

keep the established settings from being adjusted unintentionally.

To activate the child-lock, once the desired settings have been

established, depress the up button (+) and down button (–) at the

same time and hold for 3 seconds (Fig 10). To deactivate the

child-lock, depress the same up button (+) and down button (–) at

the same time and hold for 3 seconds.

NOTE: This feature will not keep the heater from being turned on.

It will, however, keep the controls from being adjusted once the

heater has been set.

HZ-3220 OPERATION

(CONTINUED)

Fig. 9

Fig. 8

Fig. 7

Heat Output

Control

Thermostat

Control

Power

Button

Fig. 10

HZ-2200-3200-3220_OM_Rev1.qx 6/8/05 1:19 PM Page 5

SAFETY FEATURES

These heaters are equipped with several devices and features for added protection:

• SafeGuard

™

Alert Heat Indicator Badge visually indicates the grille is hot by turning from black to red

(HZ-3220 Series only). When the grille begins to cool after the heater is shut off the badge will turn

black again.

• Child Resistant push-to-turn power control knob (HZ-2200 Series and HZ-3200 Series) or a child-lock

feature (HZ-3220 Series).

• A tip-over switch that disables the heater if it is accidentally tipped forward or backward.

• A high temperature safety control prevents overheating (HI limit).

• This heater is also equipped with a thermal cut-off fuse that will permanently shut down the heater

should it operate at a higher than normal temperature.

• This heater was created using a high quality safety plastic.

CLEANING AND STORAGE

CLEANING

We recommend that the heater be cleaned at least once a month and before off-season storage.

• Turn the heater OFF and unplug it. Allow it to cool.

• Use a dry cloth only to clean the external surfaces of the heater. DO NOT USE WATER, WAXES,

POLISHES OR ANY CHEMICAL SOLUTION.

STORAGE

• Clean your heater using the above-mentioned steps, then store it in a cool, dry place.

• This heater does not disassemble.

TROUBLESHOOTING

If your heater shuts off unexpectedly or fails to operate, one of your heater safety features may have been

activated to prevent overheating.

• Be sure it is plugged in and that the electrical outlet is working.

• Check your Thermostat setting. The unit may simply be off because you have reached your desired

heat setting.

• Check for any obstructions. If you find an obstruction, turn the heater OFF and unplug it. Allow the

heater to cool completely, then remove the obstruction. Wait at least 10 minutes, then re-plug the

heater in and follow the OPERATION instructions.

ELECTRICAL RATING

This product is rated 12.5 Amps (1500 watts) @ 120V, 60Hz.

HZ-2200-3200-3220_OM_Rev1.qx 6/8/05 1:19 PM Page 6

You should first read all instructions before

attempting to use this product.

A. This 5 year limited warranty applies to repair

or replacement of product found to be

defective in material or workmanship. This

warranty does not apply to damage resulting

from commercial, abusive, unreasonable use or

supplemental damage. Defects that are the

result of normal wear and tear will not be

considered manufacturing defects under this

warranty. KAZ IS NOT LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES

OF ANY NATURE. ANY IMPLIED WARRANTY

OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE ON THIS PRODUCT IS

LIMITED IN DURATION TO THE DURATION OF

THIS WARRANTY. Some jurisdictions do not

allow the exclusion or limitation of incidental or

consequential damages or limitations on how

long an implied warranty lasts, so the above

limitations or exclusions may not apply to you.

This warranty gives you specific legal rights,

and you also may have other rights which vary

from jurisdiction to jurisdiction. This warranty

applies only to the original purchaser of this

product from the original date of purchase.

B. At its option, Kaz will repair or replace this

product if it is found to be defective in material

or workmanship. Defective product should be

returned to the place of purchase in

accordance with store policy. Thereafter, while

within the warranty period defective product

may be returned to Kaz.

C. This warranty does not cover damage resulting

from any unauthorized attempts to repair or

from any use not in accordance with the

instruction manual.

D. Return defective product to Kaz, Incorporated

with a brief description of the problem. Include

proof of purchase and a $10 US/$15.50 CAN

check or money order for handling, return

packing and shipping charges. Please include

your name, address and a daytime phone

number. You must prepay shipping charges.

Send to:

In U.S.:

Kaz, Incorporated

Attn: Returns Department

4755 Southpoint Drive

Memphis, TN 38118

USA

In Canada:

Kaz, Incorporated

Attn: Returns Department

510 Bronte Street South

Milton, ON L9T 2X6

Canada

P/N: 31IM2200295

5 YEAR LIMITED WARRANTY

CONSUMER RELATIONS

Mail questions or comments to:

Kaz, Incorporated

Consumer Relations Dept.

250 Turnpike Road

Southborough, MA 01772

Call us toll-free at: 1-800-332-1110

E-mail: consumerrelations@kaz.com

Or visit our website at: www.kaz.com

Please be sure to specify a model number.

NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST, RETURN

THE HEATER TO THE ORIGINAL PLACE OF PURCHASE OR SEE YOUR WARRANTY. DO NOT ATTEMPT TO

OPEN THE MOTOR HOUSING YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE

TO THE HEATER OR PERSONAL INJURY.

HZ-2200-3200-3220_OM_Rev1.qx 6/8/05 1:19 PM Page 7

HZ-2200-3200-3220_OM_Rev1.qx 6/8/05 1:19 PM Page 8

Honeywell HZ-3200 Series Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info