478015
7
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
7 EN
HOT START
The machine is considered to be "hot" if the engine has been
running for more than 5 minutes in the 10 minutes before starting
up.
The hot start procedure is the same as the cold start procedure
except that the choke [1] is not needed. (The lever must be left in
the low position).
NOTE:
Should you have difficultie store-start a hot engine, follows
this procedure:
1. Turn the engine to the OFF position (O).
2. Make sure that the choke lever is in OPEN position.
3. Keep the throttle control lever (throttle trigger) fully squeezed.
4. Pull the starter grip 3 to 5 times, and release the throttle control
lever (throttle trigger).
5. Start the engine referring to the procédures described above.
CAUTION:
Be sure to turn the engine switch to the OFF position (O).
If this operation is executed with the engine switch at the ON
position, the blade may rotate when the engine starts and a
personal injury may result.
STOPPING THE ENGINE
1. To stop the engine, press the Start/Stop button to engage the
Stop position (O) [2].
2. This step can also be taken to stop the machine in case of
emergency.
Note that the cutting attachment continues turning by inertia
after the engine has been stopped.
OPERATION
OPERATING POSITION
Once the machine has been started,
attach it to the harness as already
described in the section on preparation.
When handling the machine, take care to avoid striking any
objects with the cutting attachment and keep the cutting
attachment away from your body. Do not use the machine
unless it is attached to the harness.
Hold the brush cutter firmly by both grips as shown. Always keep
firm footing on both feet when working. Take appropriate breaks
and vary your working position.
CAUTION:
When using the machine, always allow the engine to idle between
operations. If the machine is allowed to run at maximum speed
with no load (no resistance on the cutting attachment) for long
periods, the engine may be seriously damaged.
WITH NYLON LINE TYPE CUTTING
HEAD
This attachment is designed to complete the job
done with a lawnmower. It is especially handy
and efficient for cutting grass along walls or
fences, around trees or posts and on narrow or uneven surfaces
where a lawnmower cannot be used.
Make sure the line cutting blade is properly mounted on the
cutting attachment guard.
LINE LENGTH ADJUSTMENT
At maximum rotating speed, gently press the nylon line cutting head
on the ground. The line is automatically extended. Repeat this
operation until the optimal length is obtained.
When the engine is started and the cutting attachment starts
rotating, the excess line will automatically be cut by the line cutter
located on the guard.
CUTTING
The nylon line cuts grass cleanly without damaging tree bark and
avoiding the violent impacts that would occur between a rigid cutting
attachment and hard surfaces.
It is, however, recommended not to work too long in such areas in
order to avoid damaging fragile, immature plant, in particular, and to
avoid premature line wear.
Proceed in stages, when trimming, tilting the cutting attachment
slightly.
For larger areas, hold the cutting attachment horizontal and sway it
sideways from right to left and from left to right, alternately.
[1]
[2]
[2]
SAFETY
Read the
safety
instructions
SAFETY
A4 C11
3
2
1
7

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Honda-UMK435E

Zoeken resetten

  • Hoe kan ik de maaidraad
    het beste bevestigen in de maaikop Gesteld op 16-8-2024 om 10:46

    Reageer op deze vraag Misbruik melden
  • De machine slaat af bij bij belasting.
    Ben 2 keer bij lecoba geweest. Maar ze weten het niet op te lossen. Gesteld op 30-6-2023 om 16:45

    Reageer op deze vraag Misbruik melden
  • motor start enkel op choke en valt dan stil na het afzetten van choke Gesteld op 4-7-2020 om 12:03

    Reageer op deze vraag Misbruik melden
  • Hallo, mijn vader heeft een jaar geleden een Honda umk435e aangekocht deze maaier heeft al 4 keer binnen geweest voor herstelling. Bij vol gas valt hij altijd stil, voor de rest start en draait hij zeer goed. In het tuincentra beweren ze dat de machine al 2keer is binnen geweest bij Honda zelf en dat er al een aantal onderdelen zijn vervangen , zoals de carburator bv. Maar het probleem geraakt niet opgelost. Is er iemand die ons kan helpen alvast bedankt. Gesteld op 5-10-2013 om 21:09

    Reageer op deze vraag Misbruik melden
  • Wij hebben dit ook, maar zien geen reactie of vervangen altijd de oplossing was
    PeterG Geantwoord op 26-1-2020 om 11:26

    Waardeer dit antwoord (1) Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Honda UMK435E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Honda UMK435E in de taal/talen: Engels als bijlage per email.

De handleiding is 1,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Honda UMK435E

Honda UMK435E Gebruiksaanwijzing - Nederlands - 88 pagina's

Honda UMK435E Gebruiksaanwijzing - Nederlands - 18 pagina's

Honda UMK435E Gebruiksaanwijzing - Deutsch - 88 pagina's

Honda UMK435E Gebruiksaanwijzing - Deutsch - 18 pagina's

Honda UMK435E Gebruiksaanwijzing - English, Français, Italiano, Espanõl - 88 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info