630639
13
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
Page 9 — English
ASSEMBLY
INSTALLING THE FRONT HANDLE
See Figure 4.
Position the front handle as shown.
Depress the buttons on the handle and insert into the
frame. Press down on the handle until the button on the
handle clicks into place.
ASSEMBLING THE WHEEL/DRAG STAKE
ASSEMBLY
See Figure 5.
 Locate the axles, hitch pins, washers and wheels.
 Slide the wheel onto the axle.
 Place a washer on the outside of the wheel and slide to
rest against the wheel.
 Push the hitch pin into the hole on the end of the axle to
secure the wheel/drag stake assembly.
NOTE: The hitch pin should be pushed into the axle until
the center of the pin rests on top of the axle.
 Repeat with the second wheel.
INSTALLING THE WHEEL /DRAG STAKE
ASSEMBLY
See Figure 6.
Use the wheel/drag stake assembly to transport the unit to
and from the work area or when cultivating.
To install:
Remove the adjustment knob located at the back of the
tine shield.
Insert the wheel/drag stake assembly into the bracket at
the back of the tine shield. To place the wheels in a high
position, insert the knob in the first hole. For a lower wheel
position, insert the knob in the second or third hole.
Insert adjustment knob through holes in bracket, pass-
ing through desired hole in wheel/drag stake assembly,
to secure wheel/drag stake assembly at desired height.
Thread the adjustment knob into the nut and tighten, to
secure wheel/drag stake assembly.
INSTALLING THE TINES
See Figure 7.
The cultivator has four tines —two inner tines stamped B
and C, and two outer tines stamped A and D. For correct
operation of the unit, the tines must be installed in the cor-
rect orientation.
NOTE: The view of the gearbox for tine installation is from
the front of the cultivator.
Lean the unit back on its wheels so that the handlebar
rests on the ground.
Place tine C on the tine shaft to the left of the gear box.
The stamped side of the tine should face away from the
gear box.
Place tine B on the tine shaft to the right of the gear box.
The stamped side of the tine should face away from the
gear box.
Place a felt washer on each side of the tine shaft, and
slide to rest against the inner tines.
Place the outer tine stamped D on the left side of the tine
shaft. The stamped side should face in toward tine C.
Place the outer tine stamped A on the right side of the
tine shaft. The stamped side should face in toward
tine B.
NOTE: When installed correctly, the angled edge of the
tine blades should face the ground.
To secure the tines to the tine shaft, insert the hitch pin
into the holes located on either side of the tine shaft.
NOTE: The unit will not operate properly if the tines are
installed incorrectly. If you notice a problem with the cultivat-
ing operation of the unit, check for proper tine positioning.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Homelite UT46510 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Homelite UT46510 in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 7,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Homelite UT46510

Homelite UT46510 Snelstart handleiding - English, Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info