381174
64
Verklein
Vergroot
Pagina terug
1/74
Pagina verder
63
English
3. Extension bar: WR12DM2: Code No. 873633
WR9DM2: Code No. 996143
The extension bar is convenient for working in very
restricted spaces or when the socket provided cannot
reach the bolt to be tightened.
CAUTION:
When the extension bar is used, the tightening torque
is reduced slightly compared with the ordinary socket.
4. Universal joint: WR12DM2: Code No. 992610
WR9DM2: Code No. 996147
The universal joint is convenient for impacting nuts
when there is an angle between the socket and
wrench, or when working in a very narrow space.
5. Duct Socket: (WR12DM2)
This is used for tightening bolts and nuts on flange
sections of air conditioners, type ducts, etc.
6. Corner attachment (Model EW-14R) (WR12DM2)
Use this attachment only when the machine is applied
to the nut or bolt at the right angle.
7. Bit adaptor: Code No. 322752 (WR12DM2)
This is used for tightening small screws (M6 – M8).
NOTES:
(1) This adaptor is set only on the anvil (drive angle) of
the main unit. The bit adapter cannot be attached to
the special accessory anvil (square drive).
(2) Before starting work with the adapter, tighten a few
screws with it to make sure it’s tightening with the
appropriate torque.
Code No.
Hexagonal width
across flats (mm)
993658 12
992613 13
992615 14
(3) Tightening speed will be greatly reduced when driving
wood, tapping or other similar screws.
Optional accessories are subject to change without notice.
APPLICATION
<WH12DM2, WH9DM2>
Driving and removing of small screws, small bolts,
etc.
<WR12DM2, WR9DM2>
Tightening and loosening of all types of bolts and
nuts, used for securing structural items.
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery latch to
remove the battery. (Figs. 1 and 2)
CAUTION:
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2).
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger’s power cord to a receptacle.
When the power cord is connected, the charger’s
pilot lamp will blink in red. (At 1-second intervals).
2. Insert the battery into the charger.
Insert the battery firmly, in the direction shown in
Fig. 3 and 4, until it contacts the bottom of the charger
compartment.
CAUTION:
If the battery is inserted in the reverse direction, not
only recharging will become impossible, but it may
also cause problems in the charger such as deformed
recharging terminal.
3. Charging
When inserting a battery in the charger, charging will
commence and the pilot lamp will light continuously
in red.
When the battery becomes fully recharged, the pilot
lamp will blink in red. (At 1-second intervals.) (See
Table 5)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 5, according to the condition of the charger or
the rechargeable battery.
64

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi wh12dm2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi wh12dm2 in de taal/talen: Engels, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,77 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Hitachi wh12dm2

Hitachi wh12dm2 Gebruiksaanwijzing - English - 130 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info