571648
8
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
7
English
2. Screw feed attachment installation
Perform the installation procedures in the reverse
sequence of the removal procedures.
Position the screw feed attachment over the main
body and align the “
” mark of the main body
and the “
”mark of the screw feed attachment
then turn the attachment in the direction of the
”mark shown in Fig. 2 to fix it.
3. Driver bit installation and removal
Collate screw tightening cannot be performed except
by the genuine driver bits for Model WF4V.
Install the bit securely by the following procedures.
Move the guide sleeve to the top edge, insert the
bit into the hexagonal hole of the anvil and then
release the guide sleeve. (Fig. 3)
When removing the bit, perform the installation
procedures in the reverse order.
CAUTION
If the guide sleeve does not return to its original
position, then the driver bit is not installed properly.
HOOK INSTALLATION
(1) Insert the hook into the “A” section of the main
body then turn it clockwise to set the clearance
between the housing and hook to the appropriate
position.
Tighten the nut clockwise to fix the hook securely.
(Fig. 4)
(2) The hook can be hung on your belt or on a pipe
with a diameter of up to 32 mm.
BELT GUIDE INSTALLATION AND REMOVAL
(1) To use as an impact driver, remove the belt guide
by grasping it with the thumb and forefinger and
pulling it in the direction indicated by the arrow
(Fig. 5).
(2) When attaching the belt guide, align point B of the
guide with point C of the housing and press in the
direction indicated by the arrow until the belt guide
clicks into place. (Fig. 6)
RUBBER COVER (B) INSTALLATION
If it is necessary to block the air coming out from one
of the air openings, block the air opening by using the
rubber cover (B) provided. Press the protruding part
of the cover firmly into the air opening, pressing evenly
around the edge, to insert it with the least effort.
(Fig. 7)
NOTE:
When the rubber cover (B) has been used to close the
air opening on one side, the air opening on the opposite
side must be left completely open and unobstructed.
If this is not done, there is a danger that the motor
may burn out.
SCREW LENGTH AND SCREW-IN DEPTH
ADJUSTMENT
The tightening depth of this machine can be adjusted
by rotating the knob.
The tightening depth is adjusted by rotating the knob
and setting the stopper to the numerals (screw length)
indicated on the slider case.
Select a top adjuster to match screw length to be used
and attach it to the top edge. (Refer to Fig. 9, 10)
Store the top adjuster in the storage room on the side
face of the slider case when it is not used.
The top adjuster is stored easily when the button
shown in Fig. 8 is pressed.
(1) In case that you use a screw which has a length
of 25 – 32 mm (L), please use the top adjuster No.
1 (small). (Fig. 9)
Match the stopper to the screw length (25 – 32).
(2) In case that you use a screw which has a length
of 35 – 41 mm (L), please use the top adjuster No.
2 (large). (Fig. 10)
Match the stopper to the screw length (35 – 41).
[Fine adjustment of tightening depth]
The tightening depth adjustments (1) to (2)
mentioned above are just preliminary.
Perform fine adjustment after trial driving.
Rotate the knob in
direction when the screw
head is too high.
Rotate the knob in
direction when the screw
head is too low.
(Refer to Fig. 11)
COLLATED SCREW STRIPS INSTALLATION
AND REMOVAL
1. Installation
(1) Insert the tape tip of collated screw strips into the
belt guide groove (D section).
(2) Next, insert the tape tip into the slider groove (E
section) and feed to push in the \ direction.
(Fig. 12 and Fig. 14)
(3) Set the collated tape so that the first screw is lined
up with the slider screw mark. (Fig. 13 and Fig. 14).
NOTE:
If the tape is not set as shown in the figure, the
bit can damage the board surface (inadequate feed)
and screws can be wasted (excess feed).
2. Removal
When the screws on the tape run out or to remove
a half used belt of screws, pull the tape out in the
\ direction as shown in Fig. 15.
HOW TO USE THE AUTOMATIC
SCREWDRIVER
1. Operations
When you pull the switch and press the driver
straight against the workpiece in continuous
operation mode, the screw is fed and screwed in
automatically. (Fig. 16)
2. Tightening at a corner and adjustment operation
When the screw is tightenined, retightened or
removed in a location where the tightening is
impossible if the screw feed attachment is installed
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi WF4V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi WF4V in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 0,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info