571647
12
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
English
12
7. Mode switching feature (Fig. 17)
The screw driver has a mechanism for switching modes,
allowing it to output pressure in two steps to suit the
conditions with di erent materials. The Normal mode has
little recoil, so works well when the nish is important,
while the Power mode is for jobs that require powerful
tightening.
: can be used
×: cannot be used
Application Normal Mode Power Mode
Gypsum board + wood studs
Plywood + wood studs
○○
Steel studs
(Thickness)
0.4 mm or less
×
0.4 – 0.6 mm ○○
0.6 – 0.8 mm
×
NOTE
Disconnect the air hose before switching modes.
Clean and oil the area around the mode lever periodically.
We recommend using the Normal mode with steel studs
if possible and using the Power mode if screws are not
penetrating far enough.
Take particular note that the Power mode cannot be used
with 0.4 mm steel studs. Always use the Normal mode.
Screws may pierce too far and strip out the metal or they
may not hold the material.
When using the Normal mode, if the materials are too
hard and screws are not getting tight, switch to the Power
mode.
When driving screws into plywood in the Power mode,
hold the body of the driver rmly with both hands to keep
it from shaking. (Fig. 18)
If the driver vibrates, the bit may lose contact with the
screw and fail to tighten it.
When starting work in the Normal mode, the driver may
not start properly on the rst try. If this happens, switch
the mode lever to Power mode temporarily and after two
or three screws, switch back to the Normal mode and use
it.
When in the normal mode, the pressure inside the high-
pressure screw driver is essentially the same all the time,
regardless of the pressure on the air compressor side.
Consequently, even if the pressure on the air compressor
side is raised, the pressure inside the driver does not
change.
The screw driver may not perform well when used in the
cold.
8. Relief valve (Fig. 19)
The relief valve is a mechanism that functions when the
pressure inside the driver exceeds 10 bar, expelling air out
of the exhaust port and decreasing the pressure inside the
driver.
The relief valve is inside the exhaust port.
When using the high pressure screw driver, if the relief valve
should operate and leak air, take the following steps to stop
the leak.
(If the air leak does not stop on the rst try, repeat steps 1
to 3 several times.)
1 Immediately disconnect the air hose.
2 Wait until the air compressor's pressure returns to 17.6
bar or more.
3 Reconnect the air hose.
CAUTION
Put the dust cap on the air plug when not using the screw
driver or during breaks from work.
If dirt or dust from drywall gets into the screw driver via
the air plug, it may reduce the ability of the high-pressure
reducing valve to seal.
When not in use or during breaks from work, always
disconnect the air hose.
If you leave the air hose connected when the ability of the
high-pressure reducing valve is compromised, over time
air will leak little by little from the air hose (high pressure)
into the screw driver, raising the pressure inside it, which
may cause the relief valve to actuate.
Make a habit of draining the water inside the air
compressor.
If foreign matter such as rust in the drain gets inside the
high-pressure reducing valve, it will reduce its ability to
seal.
The high-pressure screw driver is equipped with a high-
pressure reducing valve that reduces the pressure from
the high pressure air hose side at 17.6 to 22.6 bar to a
normal pressure (about 8.2 bar). If debris gets inside this
high-pressure reducing valve, it reduces its ability to seal
properly and in such a state, if an air hose is left attached
for a long time, the pressure inside the screw driver will
rise gradually. This will eventually actuate the relief valve,
allowing air to leak violently from the exhaust port.
REPLACING THE BIT
If the bit starts losing contact with the screw frequently during
fastening, (bit fails to engage with the head of the screw,
spins out and fails to tighten the screw) it is time to change
the bit. Replace with a new part as soon as possible.
Use the bit changing tool that comes with the driver and
replace the bit as follows.
CAUTION
Always disconnect the air hose and unload all the screws
when changing the bit.
NOTE
Make sure no powder, dust or debris gets inside the
screw driver while changing the bit.
Such foreign matter can damage the screw driver.
Bits are consumable parts. If you continue to use a
worn bit, it may become impossible to replace it due
to damage to the bit's cross or to internal parts. At the
same time, work e ciency su ers and screws fail to be
fastened properly. Replace worn bits with new ones as
soon as possible.
1. Removing the bit
(1) Disconnect the air hose.
CAUTION
The bit cannot be replaced unless the air hose is
disconnected.
(2) Open the screw guide.
Open the vertical guide, insert the tip of the bit changing
tool in the muzzle and align it to the cross on the tip of the
bit. (Fig. 20)
(3) While pressing the bit changing tool against the bit, turn it
counterclockwise about 10 turns until the bit is detached
from inside the screw driver. (Fig. 21)
(4) Take the bit changing tool out, lower the muzzle, open
the vertical guide and the bit can be removed. (Fig. 22)
01Eng_WF4H2_WE.indd 1201Eng_WF4H2_WE.indd 12 2012/04/18 14:36:192012/04/18 14:36:19
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi WF4H2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi WF4H2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 3,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info