571640
11
Verklein
Vergroot
Pagina terug
1/70
Pagina verder
English
10
During cutting work, securely hook the rebar to the
reaction stopper B. Furthermore, secure enough
length of the rebar to be hooked to the reaction
stopper B.
Set the rebar in the center or the recess of the cutter
during cutting work. Any cutting work with the
rebar set on corners or ends of the cutter can result
in the pieces of broken rebar flying around or the
damage to the cutter and the machine.
1. Cutting (Fig. 3.)
(1) Turn the lever in the direction of the arrow mark
and open the cover.
(2) Set the setting dial at the “cut” position. (Turn the
setting dial all the way clockwise.) (Fig. 3.)
(3) Set the unit in the position shown in Fig. 3.
(4) Set the rebar to be cut on the lower cutter.
(5) When the rebar is set, make sure that either the
reaction stopper A or B is hitched to the rebar.
(6) Pull the switch trigger and cut the rebar.
CAUTION
For the sake of safe operation, this unit is designed
so that the switch cannot be inadvertently switched
on. When switching the tool on, press the lock
button and then pull the switch trigger (Fig. 2). If
the switch trigger is pulled without pressing the
lock button first, the switch may be damaged. Please
use care when switching the tool on.
Even after the cutting has been completed, continue
pulling the switch trigger until the motor starts to
run in the reverse direction and the cutter starts
to return. If the switch trigger is released too early,
the cutter will not return and the trigger will have
to be pulled again.
If the switch is turned off and then immediately
turned on again, the motor may not start. Wait for
at least one full second before attempting to turn
the motor on again after it has been switched off.
A slip clutch is built in the machine to protect the
mechanism.
If you process the material with the diameter or
quality beyond the capacity, the slip clutch can
sometimes function. In such a case, stop processing
immediately and check the material.
When the slip clutch works, a big slip noise occurs,
but it’s not a malfunction.
2. Removing the rebar during cutting operation. (Fig.
4.)
If the switch trigger is released in the middle of
cutting, the cutter can come to a stop at a halfway
position, jumming the rebar in the unit.
When this occurs, you can either pull the switch
trigger again and cut off the rebar, or you can free
the rebar by bringing the upper cutter back up to
the home position by carrying out the following
procedure. (Fig. 4.)
Removing (Fig. 5.)
Set the setting dial to the “RETURN” position as
shown in Fig. 5. and pull the switch trigger again.
SERVICE LIFE AND REPLACEMENT OF THE
CUTTER
1. Service life of cutter (Fig. 6.)
Repeated cutting of the rebar can result in the
“wear and tear”, “deformation,” nicked edges”, etc.
Using the cutter under such circumstances will not
only damage the machine but also there will be a
fear of the broken cutter fragments flying around.
Replace it with a new cutter after cutting about
8,000 pieces of rebar (a rough guide).
2. Before removing the cutter
WARNING!
To prevent accidents, always be sure to turn the switch
OFF and unplug the power cord from the receptacle.
(1) Pull the switch lightly and let the upper cutter move
slowly. When the hexagon socket bolt that fixes the
upper cutter comes out of the cam cover, turn the
switch OFF and stop the motor.
(2) Unplug the power cord from the receptacle.
3. Removal
If you remove the hexagon socket bolt using the
provided Allen key, you can remove the cutter.
(Pushing the cutter guard up in the direction of the
arrow shown in Fig. 7, facilitates removal of the
upper cutter.)
Removal of the lower cutter can be easily made if
the lower cutter is wrenched with a Phillips head
screwdriver as shown in the following diagram.
(Fig. 8)
4. Mounting
(1) Get rid of dust around the cutter installing section
and clean it up.
(2) Align the hole of a new cutter and the position of
a pin, and insert it into the installing section.
(3) Also replace the hexagon socket bolt (packed along
with the cutter) with a new one simultaneously,
completely tighten it using the attached Allen key,
and then fix the cutter.
HOW TO USE (BENDING)
WARNING!
Note that the unit is not a hand-held tool. Be
absolutely sure to use the unit only after placing
it on a stable spots such as floor, ground, etc.
Never bring your hand close to the bending roller
during operation.
Never bend any materials other than the rebars. If
you attempt to do so, the material can splinter into
pieces and scatter.
Bend less than every 3 pieces of rebar with a 10mm
diameter, less than every 2 pieces with a 12 mm
diameter, and every 1 piece with a 16mm diameter.
Remember that the cutter moves even during the
bending operation, thereby, close the cutter cover
without fail.
Begin operation only after marking sure that there
are no people within the turning range of the material
to be bent.
Reserve an extra length of at least 200 mm on the
bending length of the rebar to be bent. (Fig. 9)
If the extra length is not long enough, the rebar
can come off during bending operation, or it can
break into fragments and scatter dangerously.
Place the rebar on the center plate and set it so
that it is horizontal with the turntable surface.
If the side that is to be bent is set inclined upward,
the rebar can come loose from the bending roller
while bending causing it to fly off. (Fig. 10)
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi VB16Y bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi VB16Y in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 7,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info