571105
12
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
12
English
Angle transmission (Fig. 36)
Check angle transmission or angle gear for grease level about every
50 hours of operation by removing the grease ller plug on the side
of angle transmission.
If no grease can be seen on the anks of the gears, ll the
transmission with quality lithium based multipurpose grease up to
3/4.
Do not completely ll the transmission.
Maintenance schedule
Below you will nd some general maintenance instructions. For
further information please contact Tanaka dealer.
Daily maintenance
Clean the exterior of the unit.
Clean the chain oil lter port.
Clean the groove and oil lter port in the guide bar.
Clean the side case of saw dust.
Check that the saw chain is sharp.
Check that the bar nuts are su ciently tightened.
Make sure that the chain transport guard is undamaged and that
it can be securely tted.
Check that nuts and screws are su ciently tightened.
Weekly maintenance
Check the starter, especially cord and return spring.
Clean the exterior of the spark plug.
Remove the spark plug and check the electrode gap. Adjust it to
0.6 mm or change the spark plug.
Clean the cooling ns on the cylinder and check that the air
intake at the starter is not clogged.
Clean the air lter.
Monthly maintenance
Rinse the fuel tank with gasoline, and clean fuel lter.
Clean chain oil lter.
Clean the exterior of the carburetor and the space around it.
Clean the fan and the space around it.
Clean the mu er of carbon.
CHAIN SHARPENING
Parts of a cutter (Fig. 37, 38)
WARNING
Gloves should be used when sharpening chain.
35. Top plate
36. Working corner
37. Side plate
38. Gullet
39. Heel
40. Chassis
41. Rivet hole
42. Toe
43. Depth gauge
44. Correct angle on top plate (degree of angle depends on chain
type)
45. Slightly protruding “hook” or point (curve on non-chisel chain)
46. Top of depth gauge at correct height below top plate
47. Front of depth gauge rounded o .
LOWERING DEPTH GAUGES WITH A FILE
1) If you sharpen your cutters with a le holder, check and lower the
depth.
2) Check depth gauges every third sharpening.
3) Place depth gauge tool on cutter. If depth gauge projects, le
it level with the top of the tool. Always le from the inside of the
chain toward an outside cutter. (Fig. 39)
4) Round o front corner to maintain original shape of depth gauge
after using depth gauge tool. Always follow the recommended
depth gauge setting found in the maintenance or operator
manual for your saw. (Fig. 40)
GENERAL INSTRUCTIONS FOR FILING CUTTERS
File (48) cutter on one side of the chain from the inside out. File on
forward stroke only. (Fig. 41)
5) Keep all cutters the same length. (Fig. 42)
6) File enough to remove any damage to cutting edges (side plate
(49) and top plate (50)) of cutter. (Fig. 43)
SHARPENING ANGLES FOR SHARPENING SAW CHAIN
1. Part Number
90SG-40
90PX-40
2. Pitch 3/8”
3. Depth Gauge Setting 0.025"
4. Side Plate Filing Angle 80°
5. Top Plate Angle 30°
6. File Guide Angle 90°
000Book_TCS27EPAP(S)_WE.indb 12000Book_TCS27EPAP(S)_WE.indb 12 2014/06/04 15:21:582014/06/04 15:21:58
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi TCP27EPAPS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi TCP27EPAPS in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 9,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info