661496

Hitachi TCG27ECP Handleiding

9
Verklein
Vergroot
Pagina terug
1/288
Pagina verder
English
9
○ Use only accessories as recommended for this unit/
machine by the manufacturer.
○ Before operation, make sure that there are no tools such
as the adjustment key or spanner still attached to the
unit.
WARNING
○ Never modify the unit/machine in any way. Do not use
your unit/machine for any job except that for which it is
intended.
○ Non-authorized modifi cations and/or accessories may
result in serious personal injury or the death of the
operator or others.
Fuel safety
○ Mix and pour fuel outdoors and where there are no
sparks or fl ames.
○ Use a container approved for fuel.
○ Move at least 3 m away from fueling site before starting
engine.
○ Stop engine before removing fuel cap. Do not remove
the fuel cap during operation.
○ Empty the fuel tank before storing the unit/machine. It is
recommended that the fuel be emptied after each use. If
fuel is left in the tank, store so fuel will not leak.
WARNING
○ Fuel is easy to ignite or get explosion or inhale fumes, so
that pay special attention when handling or fi lling fuel.
○ Do not smoke or allow smoking near fuel or the unit/
machine or while using the unit/machine.
○ Wipe up all fuel spills before starting engine.
○ Store unit/machine and fuel in area where fuel vapors
cannot reach sparks or open fl ames from water heaters,
electric motors or switches, furnaces. etc.
○ When using the unit in dry areas, make sure that fi re
extinguishing equipment is readily available.
○ If you shut off the engine for refueling, make sure the unit
has cooled down before adding fuel.
Cutting safety
○ Do not cut any material other than grass and brush.
○ Inspect the area to be cut before each use.
Remove objects which can be thrown or become
entangled.
Do not operate in areas where there are tree roots or
rocks.
○ For respiratory protection, wear an aerosol protection
mask when cutting the grass after insecticide is
scattered.
○ Keep others including children, animals, bystanders and
helpers outside the 15 m hazard zone. Stop the engine
immediately if you are approached.
○ Please exercise caution as engine startup may be
delayed after pulling the starter handle.
○ Always keep the engine on the right side of your body.
○ Hold the unit/machine fi rmly with both hands.
○ Keep fi rm footing and balance. Do not over-reach.
Losing your balance during work may lead to an injury.
○ Keep all parts of your body away from the muffl er and
cutting attachment when the engine is running.
○ Keep cutting attachment below knee level.
○ Please exercise caution when operating in areas where
electrical cables or gas pipes are present.
○ Do not operate the cutting attachment for anything but
clearing grass or bushes. Avoid operations where the
cutting attachment may touch water such as puddles
or dig into dirt. Failure to do so may result in injury or
damage to the unit.
○ Avoid prolonged use at low speed range in which
vibration is high. Doing so may result in engine damage.
○ When relocating to a new work area, or inspecting,
adjusting or exchanging the unit’s cutting attachments,
accessories, etc., be sure to shut off the machine and
ensure that all cutting attachments are stopped.
○ Never place the machine on the ground when running.
○ Never touch the cutting attachment when it is rotating.
○ Always ensure that the engine is shut off and any cutting
attachments have completely stopped before clearing
debris or removing grass from the cutting attachment.
○ Always carry a fi rst-aid kit when operating any power
equipment.
○ Turn off the engine and make sure the cutting attachment
has come to a full stop before removing the unit from
your body or before leaving the unit unattended.
○ If you accidentally bump or drop the unit, inspect it
immediately to make sure there are no damage, cracks
or deformations.
○ If the tool is operating poorly and produces strange noise
or vibrations, turn off the engine immediately and ask
your dealer to have it inspected and repaired.
Continued use under these conditions could lead to
injury or tool damage.
○ Use in accordance with local laws and regulations.
WARNING
KICKBACK DANGER (Fig. 3)
When using metal cutting attachments such as blades,
contact with obstacles such as trees or other hard
surfaces with the front or right portion of the spinning
attachment may force the unit to catch on an obstacle,
resulting in a kickback reaction towards the right side of
the operator.
Kickback may occur when the cutting attachment comes
into contact with tree stumps or rocks hidden behind
weeds. Always make sure there are no obstacles hidden
by weeds before starting work.
To minimize the danger of kickbacks when they do occur,
always position the unit to the right side of the body
during operation. With the operator properly positioned
as the cutting attachment rotates, this will reduce the
danger of the unit’s direct contact with the body.
Maintenance safety
○ Maintain the unit/machine according to recommended
procedures.
○ Disconnect the spark plug before performing
maintenance except for carburetor adjustments.
○ Keep others away when making carburetor adjustments.
○ Use only genuine Tanaka replacement parts as
recommended by the manufacturer.
CAUTION
Do not disassemble the recoil starter. There is a
possibility of personal injury with recoil spring.
WARNING
Improper maintenance could result in serious engine
damage or in serious personal injury.
Transport and storage
○ Carry the unit/machine by hand with the engine stopped
and the muffl er away from your body.
○ Allow the engine to cool, empty the fuel tank, and secure
the unit/machine before storing or transporting. Failure to
do so may result in fi re or accidents.
○ Empty the fuel tank before storing the unit/machine. It is
recommended that the fuel be emptied after each use. If
fuel is left in the tank, store so fuel will not leak.
○ Store unit/machine out of the reach of children.
○ Clean and maintain the unit carefully and store it in a dry
place.
○ Make sure engine switch is off when transporting or
storing.
○ When transporting and storing, either remove the cutting
attachment or place the blade cover over the blade.
○ You have to secure the machine during transport to
prevent loss of fuel, damage or injury.
○ If a warning label cannot be read, peels off or becomes
indistinct, replace it with a new one. To purchase new
labels, contact
Tanaka dealer.
000Book_TCG24ECP(S).indb 9000Book_TCG24ECP(S).indb 9 2017/03/24 10:10:482017/03/24 10:10:48
… 9 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi TCG27ECP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi TCG27ECP in de taal/talen: Alle talen als bijlage per email.

De handleiding is 45,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info