571074
15
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
15
English
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate
normally. If this does not remedy the problem, consult your dealer
or the Tanaka dealer.
Condition Cause Remedy
Engine does not start
Fuel system
Fuel tank is empty or fuel level is low Fill the fuel tank with the correct fuel mix (25:1-50:1)
Fuel tank contains old fuel (offensive odor) Replace with new fuel
Too much fuel is absorbed and spark plug is
wet
1. Disconnect the spark plug and allow to dry
2. Pull the starter handle 5 or 6 times to remove the
surplus fuel
3. Attach the spark plug
4. Set the choke lever to RUN position and pull the
starter handle
Fuel lter is clogged with dirt Clean the fuel lter
Fuel pipe is bent or disconnected Ensure that the fuel ows smoothly
Carburetor malfunction Contact Tanaka dealer
Electrical
system
Stop switch lead has short-circuited Contact Tanaka dealer
Spark plug is dirty Replace or clean the spark plug
Electrode gap is too big Adjust the gap to 0.6mm
Poor connection between high tension cable
and spark plug
Reconnect
Electrical system malfunction Contact Tanaka dealer
Other Muf er exhaust port is clogged with carbon Contact Tanaka dealer for repair
Engine starts but cuts
out straightaway
Engine is apt to cut
out
Fuel system
Fuel tank is empty or fuel level is low Fill the fuel tank with the correct fuel mix (25:1-50:1)
Fuel tank contains old fuel (offensive odor) Replace with new fuel
Two-cycle oil has not been added Contact Tanaka dealer
Choke lever is in START position Set the choke lever to RUN position
Air has got into fuel system Reconnect the fuel pipe or joint
Carburetor malfunction Contact Tanaka dealer
Electrical
system
Ignition failure
Spark plug failure Replace with new spark plug
Electrical system failure Contact Tanaka dealer
Other
Engine overheating
Wrong spark plug model
Replace with designated part
See “SPECIFICATIONS”
Dirty air cleaner Clean
Carbon clogging (muf er exhaust port) Clean
Insuf cient compression (piston, piston ring,
cylinder)
Contact Tanaka dealer
Abnormal vibration
Cutting attachment is not properly installed See “Installation of cutting attachment”
Handle, handle bracket or other fastening part
is loose
Check and tighten
Blade is bent or damaged Replace with new blade
Grass is wrapped round gear case Remove grass
Engine is running but blade does not
move
Movement is poor
Grass is wrapped round gear case Remove grass and dirt
Engine does not stop Stop switch failure
Set the choke lever to START position to stop the
engine
Cease use immediately and contact Tanaka dealer
Engine stops when throttle is closed Idle speed is too low Contact Tanaka dealer
Blade continues rotating when throttle
is closed
Idle speed is too high
Throttle wire is too taut
Contact Tanaka dealer
000Book_TCG24EBSP_WE.indb 15000Book_TCG24EBSP_WE.indb 15 2014/03/26 14:05:132014/03/26 14:05:13
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi TCG24EBDPSLN bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi TCG24EBDPSLN in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 10,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info