568891
5
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
4
English
(3) After inserting the nails, pull the nail feeder up in
backward direction, remove it from the roll pin, move
it slowly forward and push the nail.
NOTE:
After having removed the nail feeder from the roll pin
and moving it forcefully forward, the nail coupling
may brake and the nail feeder may get caught between
the magazine and nails, causing poor nail feeding.
Therefore, move the nail feeder slowly forward.
CAUTIONS
To prevent unintentional operation, never touch the
trigger or place the top end of the push lever on a work
bench on floor. Also, never face the nail outlet toward
any part of a person.
Use nails in which five nails are connected.
HOW TO USE THE NAILER
CAUTIONS
Never use the head or body of this device as a hammer.
Take precautions to ensure the safety of persons in the
vicinity during operation.
1. Nailing procedures
(1) Intermittent nailing
Depress the nail outlet onto the desired point; then
pull the trigger to drive a nail in a single shot. (See Fig.
3)
Fig. 3
CAUTION
This tool will sometimes fire twice in rapid succession
when strongly pressed flush against a surface or
when using on hard materials. In such cases, fire the
nails by squeezing and quickly releasing the trigger.
(2) Push lever
When depressing the nail outlet, be sure to fully lift the
push lever (See Fig. 3) to release the safety lock. Thus,
nails cannot be driven without releasing the safety
lock even though the trigger is pulled.
(3) Continuous nailing
First, pull the trigger. Then depress the devise onto the
desired position to automatically drive nails. (See Fig.
4).
Fig. 4
CAUTION
Excercise care when nailing corners of lumber. When
continuous nailing corners of lumber, a nail may go
astray or break through the corner.
NOTES
Precautions on no-load operation
Sometimes nailing will continue after driving in all
nails previously contained in the magazine.
This is termed no-load operation. Such operation
may deteriorate the damper, magazine, and nail feeder.
To avoid no-load operation, occasionally confirm the
amount of remaining nails. On the other hand, all nails
should be removed after using this nailer.
After completing operation, put into the body about
2cc oil through the hose joint to protect the tool from
rust.
Under low temperature conditions, the machine
sometimes does not operate correctly. Always operate
the machine at the appropriate ambient temperature.
2. Attachment and detachment of the nose cap
CAUTIONS:
When attaching and detaching the nose cap, make
sure to disconnect the hose to release the compressed
air.
When attaching and detaching the nose cap, make
sure to take your finger off the trigger.
When you do not want to cause scratches in the material
you work with, use the accessory rubber nose cap. To
attach the nose cap, attach it as shown in Fig. 5. Detachment
shall be made in reversed order. Also, when attaching the
nose cap, the drive bit projection of the nail outlet will be
reduced and the nailing power will be lowered. Adjust the
nailing power according the air pressure used and the
attachment position of the bit guide.
Fig. 5
3
1
2
Push Lever Trigger
Previously pull the trigger.
2
1
Nose Cap
Disconnect air hose
Push Lever
1
2
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi NT65A2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi NT65A2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info