661494
14
Verklein
Vergroot
Pagina terug
1/204
Pagina verder
14
English
This Hitachi nailer is equipped with a nailer operation
switching device.
Use FULL SEQUENTIAL ACTUATION MECHANISM or
CONTACT ACTUATION MECHANISM in accordance with
the work to be performed.
Explanation of the various nailing operations
FULL SEQUENTIAL ACTUATION MECHANISM:
First, press the push lever against the wood; next, pull
the trigger to drive the nail.
Follow the same sequence to continue driving nails.
After nailing once, nailing will not be possible again until
the trigger is released and pressed again.
CONTACT ACTUATION MECHANISM:
CONTACT ACTUATION can follow two di erent
sequences, depending on your use.
To drive several nails:
1. Pull the trigger.
2. Press the push lever against the wood to drive the
nail.
3. If the trigger is held back, a nail will be driven each
time the push lever is pressed against the wood.
To drive a single nail:
1. Press the push lever against the wood.
2. Pull the trigger to drive the nail.
3. Remove your nger from the trigger and remove the
nailer from the wood.
[Dry- re lockout mechanism]
The NT1865DBAL, NT1865DBSL employs a preventive
mechanism for unloaded operation.
The NT1865DBAL, NT1865DBSL enters a state where
the push lever cannot be pushed up. This takes place
when the magazine is not loaded with nails or when the
remaining number of nails becomes less than 6 or 9.
CAUTION
Use caution not to throw the push lever tip onto wood
when the push lever cannot be pushed up.
1. Nailing procedures
This Nailer is equipped with the push lever and does not
operate unless the push lever is depressed.
There are two methods of operation to drive nails with
this Nailer.
They are:
1. Intermittent operation (Trigger re):
2. Continuous operation (Push lever re):
(1) Intermittent operation (Trigger re)
Use the FULL SEQUENTIAL ACTUATION MECHANISM
setting. (See Fig. 17)
WARNING
For intermittent operation, Set the nailing operation switch
to FULL SEQUENTIAL ACTUATION MECHANISM
(Nailing operation indicator is light in blue.) (i.e. Set to
SINGLE ACTUATION MECHANISM.)
To avoid double ring or accidental ring due to recoil.
1) Set to FULL SEQUENTIAL ACTUATION
MECHANISM.
2) Pull the trigger rapidly and rmly.
1 Set the nailing operation switch to FULL SEQUENTIAL
ACTUATION MECHANISM (Nailing operation indicator
is light in blue.)
(to set to FULL SEQUENTIAL ACTUATION
MECHANISM).
(Set the switching device to the nailing operation
indicator light in blue mode completely as shown in
the Fig. 17. Otherwise, it will be set to CONTACT
ACTUATION MECHANISM.)
2 Position the nail outlet on the workpiece with nger o
the trigger.
3 Depress the push lever rmly until it is completely
depressed.
4 Pull the trigger to drive a nail.
5 Remove nger from the trigger and lift the tool o the
wood surface completely.
To continue nailing in a separate location, move the nailer
along the wood, repeating steps 2 - 5 as required.
NOTE
Operations 3 and
4 should be done within 2 seconds
of each other. If more than 2 seconds pass after 3, the
Nailer will not work properly. If this happens, retry from
3.
(2) Continuous operation (Push lever re)
Using CONTACT ACTUATION MECHANISM (See Fig.
18)
WARNING
To avoid double ring or accidental ring due to recoil.
1) Do not press the nailer against the wood with
excessive force.
2) Separate the nailer from the wood as it recoils after
nailing.
1 Set the nailing operation switch to CONTACT
ACTUATION MECHANISM (Nailing operation indicator
is blink in blue.)
(to set to CONTACT ACTUATION MECHANISM).
(Set the switching device to the nailing operation
indicator blink in blue completely as shown in the Fig.
18. Otherwise, it will not operate properly.)
2 Pull the trigger with the Nailer o the workpiece.
3 Depress the push lever against the workpiece to drive a
nail.
4 Move the Nailer along the workpiece with a bouncing
motion.
Each depression of the push lever will drive a nail.
As soon as the desired number of nails have been driven,
remove nger from the trigger.
NOTE
Operations 2 and 3 should be done within 2 seconds
of each other. If more than 2 seconds pass after 2, the
Nailer will not work properly. If this happens, retry from
2.
WARNING
Keep your nger o the trigger except during nailing
operation, because serious injury could result if the push
lever accidentally contacts you or others in work area.
Keep hands and body away from the discharge area.
This Hitachi nailer may bounce from the recoil of driving
a nail and unwanted subsequent nail may be driven,
possibly causing injury.
NOTE
If all warnings and instructions are followed, safe
operation is possible with all two systems: FULL
SEQUENTIAL ACTUATION MECHANISM, CONTACT
ACTUATION MECHANISM.
Always handle nails and package carefully. If nails are
dropped, collating bond may be broken, which will cause
mis-feeding and jamming.
After nailing:
1) remove battery from the Nailer;
2) remove all nails from the Nailer;
2. Adjusting the nailing depth
To assure that each nail penetrates to the same depth,
be sure that the Nailer is always held rmly against the
workpiece.
If nails are driven too deep or shallow into the workpiece,
adjust the nailing in the following order.
1 Remove the battery from the Nailer.
2 If nails are driven too deep, turn the adjuster to the
shallow side. (See Fig. 19)
Adjustments are in half-turn increments.
If nails are driven too shallow, turn the adjuster to the
deep side. (See Fig. 20)
3 Stop turning the adjuster when a suitable position is
reached for a nailing test.
4 Connect the battery to the Nailer.
ALWAYS WEAR SAFETY GLASSES.
Perform a nailing test.
0000Book_NT1865DBAL.indb 140000Book_NT1865DBAL.indb 14 2017/04/14 15:11:322017/04/14 15:11:32
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi NT1850DBSL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi NT1850DBSL in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 18,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info