499908
47
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
EN-1
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital
devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15
of the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise
specified in the manual. If such changes or modifications should be made, you could
be required to stop operation of the equipment.
Notice
If static electricity or electromagnetism causes data transfer to discontinue midway
(fail), restart the application or disconnect and connect the communication cable
(USB, etc.) again.
EN-2
READ THIS FIRST
Trademark Information
Microsoft
®
and Windows
®
are U.S. registered trademarks of Microsoft Corporation.
Pentium
®
is a registered trademark of Intel Corporation.
Macintosh is a trademark of Apple Inc.
SD™ is a trademark.
SDHC™ is a trademark.
Other names and products may be trademarks or registered trademarks of their
respective owners.
Product Information
Product design and specifications are subject to change without notice. This
includes primary product specifications, software, software drivers, and user’s
manual. This User Manual is a general reference guide for the product.
The product and accessories that come with your camera may be different from
those described in this manual. This is due to the fact that different retailers often
specify slightly different product inclusions and accessories to suit their market
requirements, customer demographics, and geographical preferences. Products
very often vary between retailers especially with accessories such as batteries,
chargers, AC adapters, memory cards, cables, pouches, and language support.
Occasionally a retailer will specify a unique product colour, appearance, and
internal memory capacity. Contact your dealer for precise product definition and
included accessories.
The illustrations in this manual are for the purpose of explanation and may differ
from the actual design of your camera.
The manufacturer assumes no liability for any errors or discrepancies in this user
manual.
EN-3
SAFETY INSTRUCTIONS
Read and understand all Warnings and Cautions before using this product.
Warnings
If foreign objects or water have entered the camera, turn the power off
and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
If the camera has fallen or its case has been damaged, turn the power
off and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
Do not disassemble, change or repair the camera.
This might cause fire or electric shock. For repair or internal inspection, ask
the store of purchase.
Use the supplied AC adapter only with the indicated power supply
voltage.
Use with any other power supply voltage might cause fire or electric shock.
Do not use the camera in areas near water.
This might cause fire or electric shock. Take special care during rain, snow,
on the beach, or near the shore.
Do not place the camera on inclined or unstable surfaces.
This might cause the camera to fall or tilt over, causing damage.
Keep the battery out of the reach of children.
Swallowing the battery might cause poisoning. If the battery is accidentally
swallowed, immediately consult a physician.
Do not use the camera while you are walking, driving or riding a
motorcycle.
This might cause you to fall over or result in traffic accident.
Please use battery with complete external seals.
Do not use battery from which the seals have been damaged or removed.
This may cause leakage, explosion, or injury.
EN-4
Cautions
Insert the battery paying careful attention to the polarity (+ or –) of the
terminals.
Inserting the battery with its polarities inverted might cause fire and injury, or
damage to the surrounding areas due to the battery rupturing or leaking.
Do not fire the flash close to anyone’s eyes.
This might cause damage to the person’s eyesight.
Do not subject the LCD monitor to impact.
This might damage the glass on the screen or cause the internal fluid to
leak. If the internal fluid enters your eyes or comes into contact with your
body or clothes, rinse with fresh water. If the internal fluid has entered your
eyes, consult a physician to receive treatment.
A camera is a precision instrument. Do not drop it, strike it or use
excessive force when handling the camera.
This might cause damage to the camera.
Do not use the camera in humid, steamy, smoky, or dusty places.
This might cause fire or electric shock.
Do not remove the battery immediately after long period of continuous
use.
The battery becomes hot during use. Touching a hot battery might cause
burns.
Do not wrap the camera or place it in cloth or blankets.
This might cause heat to build up and deform the case, resulting in fire. Use
the camera in a well-ventilated place.
Do not leave the camera in places where the temperature may rise
significantly, such as inside a car.
This might adversely affect the case or the parts inside, resulting in fire.
Before you move the camera, disconnect cords and cables.
Failure to do this might damage cords and cables, resulting in fire and
electric shock.
EN-5
Notes on Battery Usage
When you use the battery, carefully read and strictly observe the Safety Instructions
and the notes described below:
Use only the specified battery (3.7V).
Avoid extremely cold environments as low temperatures can shorten the battery
life and reduce camera performance.
When you are using a new rechargeable battery or a rechargeable battery that has
not been used for an extended period of time (the battery that passed the expiry
date is an exception), it may affect the number of images that can be captured.
Therefore, to maximize its performance and lifetime, we recommend that you fully
charge the battery and discharge it for at least one complete cycle before use.
The battery may feel warm after a long period of continuous use of the camera or
the flash. This is normal and not a malfunction.
The camera may feel warm after a long period of continuous use. This is normal
and not a malfunction.
If the battery is not to be used for a long period of time, remove it from the camera
to prevent leakage or corrosion and store it after no battery power is left. Stored for
a long time in a fully charged condition, its performance may be impaired.
Always keep the battery terminals clean.
There is a risk of explosion if the battery is replaced by an incorrect type.
Dispose of used battery according to the recycle instructions.
Charge the rechargeable!battery fully before using for the first time.
To prevent short-circuiting or fire, keep the battery away from other metal objects
when carrying or storing.
This symbol mark [crossed-out wheeled bin] indicates separate col-
lection of waste batteries in the EU countries. The batteries provided
with this product shall not be treated as household waste. Please use
the return and collection systems available in your country for the
disposal of the waste batteries.
If a chemical symbol is printed beneath the symbol mark, this
chemical symbol means that the batteries contains a heavy metal at
a certain concentration. It is indicated as follows:
Hg: mercury, Cd: cadmium, Pb: lead.
CONTENTS
EN-6
7 INTRODUCTION
7 Overview
7 Package Contents
8 GETTING TO KNOW YOUR
CAMERA
8 Front View
8 Rear View
9 LCD Monitor Display
11 GETTING STARTED
11 Preparation
11 Charging the Battery
12 Initial Settings
14 CAPTURE MODE
14 Capturing Images
15 Setting the Scene Mode
16 Taking Images with Intelligent Scene
mode
17 Setting the Panorama Mode
17 Taking Images When the Smile
Feature Is On
18 Recording Shots using Face
Detection Technology
18 Self-portrait Function
19 VIDEO MODE
19 Recording Video Clips
19 Playing Back Video Clips
20 PLAYBACK MODE
20 Playing Back Still Images
20 Playback Display
21 Removing Red-eye
21 Dynamic Lighting Feature
22 Protecting Images
23 DPOF Settings
24 Erasing Images
25 MENU OPTIONS
25 Capture Menu
27 Video Menu
28 Playback Menu
30 Setup Menu
32 TRANSFERRING FILES TO
YOUR COMPUTER
32 Downloading Your Files
32 USING THE CAMERA AS A PC
CAMERA
33 EDITING SOFTWARE
INSTALLATION
34 SPECIFICATIONS
35 APPENDIX
35 Possible Number of Shots
36 Troubleshooting
EN-7
INTRODUCTION
Overview
Congratulations on your purchase of the new digital camera.
Capturing high-quality digital images is fast and easy with this state-of-the-art smart
camera. Equipped with a 12.0-megapixel CCD, this camera is capable of capturing
images with a resolution of up to 3968 x 2976 pixels.
Package Contents
Carefully unpack your camera and ensure that you have the following items:
Common Product Components:
Digital Camera
Quick Start Guide
Software CD-ROM
USB cable
AV cable
Camera strap
Camera pouch
Rechargeable lithium-ion battery
AC/DC adapter
Common (Optional) Accessories:
SD/SDHC memory card
Accessories and components may vary by retailer.
EN-8
1
5
243
6
GETTING TO KNOW YOUR CAMERA
Front View
Rear View
Item
Function
Capture Mode Video Mode Playback Mode
1. Shutter button Record button Still image: to capture mode
Video clip: to capture mode
2. :Zooms out :Zooms in :Zooms out :Zooms
in
:Zooms out :Zooms in
3. Switches to:
Video mode > Capture mode
Switches to:
Capture mode > Video mode
Still image: to capture mode
Video clip: to capture mode
4. Focus Focus Next 10th image
5. Compensation s>P -- Previous Image
6. Flash -- Next Image
7. If any scene mode is set:
switches to scene mode
selection screen
--
Still image: to display image
Video clip: to play video clip
8. Self-timer Self-timer Previous 10th image
9. Playback mode Playback mode Still image: to capture mode
Video clip: to capture mode
10. Capture menu Video menu Playback menu
1
A
B
C
D
E
F
3
4
6
8
9
5
7
10
2
A. LCD monitor
B. Status LED
C. Strap holder
D. Battery / Memory card cover
E. Tripod socket
F. USB and AV OUT terminal
1. Shutter button
2. Self-timer LED
3. ON/OFF Power button
4. Flash
5. Microphone
6. Lens
EN-9
LCD Monitor Display
Capture mode
1. Zoom status
2. Available number of shots
3. Storage media
[r] Internal memory (no card)
[ ] SD/SDHC memory card
4. Battery condition
[l] Full battery power
[o] Medium battery power
[n] Low battery power
[m] No battery power
5. Focus setting
[
K] Auto
[ ] AF Tracking
[ ] Face Detect
[O] Macro
[Q] Infinity
6. Flash mode
[
b] Auto
[a] Flash On
[d] Flash Off
[c] Red-eye
[`] Slow Sync
[_] Pre-flash
7. [s] Exposure compensation
(It can not be used in below modes: Smile
Detection, Portrait Man & Portrait Lady. )
[P] Backlight correction
(It can only be used in Portrait Man and
Portrait Lady.)
8. Self-timer & Self-portrait icon
[
i] Off
[ ] Self-portrait
[f] 2 sec.
[g] 10 sec.
[h] 10+2 sec.
9. [ ] Histogram
10. Image size resolution
[ ] 3968 x 2976
[ ] 3264 x 2448
[ ] 2304 x 1728
[ ] 1600 x 1200
[x] 640 x 480
11. Shortcut
12. Date and time
13. Quick shot
14. Capture mode icon
[] Single
[T] Continuous
[U] AEB (Auto Exposure Bracketing)
[-] Album Shot
[/] Burst
[.] Cont.flash
[+] Pre-shot
[,] Coupl.shot
[ ] Burst 30fps
15. White balance
[@] Auto
[$] Incand.
[&] Fluoresc.1
[*] Fluoresc.2
[%] Daylight
[#] Cloudy
[(] Manual WB
16. Image quality
[ ] Fine
[ ] Standard
[ ] Economy
17. ISO
[
2] Auto
[5] ISO 100
[7] ISO 200
[9] ISO 400
[0] ISO 800
[;] ISO 1600
18. Slow shutter warning
19. Mode icon / Scene mode
[ ] Auto
[] Intelligent Scene
[ ] Smile Detection
[ ] Anti-shake
[ ] Panorama
[ ] Portrait Man
[ ] Portrait Lady
[ ] Landscape
[ ] Sports
[ ] Night Portrait
[ ] Night Scene
[ ] Candlelight
[ ] Fireworks
[] Text
[ ] Sunset
[ ] Sunrise
[ ] Splash Water
[ ] Flow Water
[]Snow
[]Beach
[]Pets
[ ] Natural Green
[ ] Program AE
20. Main focus area
00214
00214
00214
13:15
13:15
13:15
SCN
SCN
SCN
SET
19
13
12
9
10
11
3
4
5
6
7
8
1
2
17
16
15
14
18
20
2010.01.01
2010.01.01
2010.01.01
EN-10
Video mode
1. Zoom status
2. Storage media
3. Battery condition
4. Focus setting
5. Flash off
6. Self-timer icon
7. Video resolution
8. Available recording time/Elapsed time
9. Date and time
10.Video quality
11. Audio off
12.Mode icon
13.Main focus area
Playback mode
!
-
!
Still image playback
1. DPOF icon
2. Protect icon
3. Folder / File number
4. Storage media
5. Battery condition
6. Image size resolution
7. Date and time
8. Histogram
9. Shutter speed/Aperture value
10.Exposure value
11. Image quality
12.ISO
13.Mode icon
Playback mode
!
-
!
Video playback
1. Protect icon
2. Folder / File number
3. Storage media
4. Battery condition
5. Volume mode
6. Total recorded time
7. Video status bar
8. Video condition icon
9. Elapsed time
10. Set key: Play/Pause hint icon
11. Down key: Stop hint icon
12.Mode icon
13
12
9
10
11
3
4
5
6
7
8
1
2
00:00:00 / 02:28:49
00:00:00 / 02:28:49
2010.01.01
2010.01.01
13:15
13:15
2010.01.01
2010.01.01
13
12
9
10
11
3
4
5
6
7
8
1
2
110-0201
110-0201
F2.8
1/3
F2.8 1/3
2
13:15
13:15
2010.01.01
2010.01.01
12
9
10
11
3
4
5
6
7
8
1
2
00:00:00 02:28:49
110-0201
110-0201
110-0201
SET
EN-11
GETTING STARTED
Preparation
1. Attach the camera strap.
2. Open the battery/memory card cover.
3. Insert the supplied battery with correct orientation as shown. (label side back)
4. Insert an SD/SDHC memory card (Optional).
The camera has
32MB internal me
mory
(10MB available for image storage),
but
you can load an SD/SDHC memory card to expand the camera’s memory capacity.
Be sure to format the memory card with this camera before its initial usage.
5. Close the battery/memory card cover and make sure it is locked securely.
To prevent valuable data from being accidentally erased from an
SD/SDHC
memory card
, you can slide the write protect tab (on the side of the
SD/
SDHC
memory card) to “LOCK”.
To save, edit, or erase data on an SD/SDHC memory card, you must
unlock the card/
To prevent damaging of an SD/SDHC memory card, be sure to turn off
the power when inserting or removing the SD/SDHC memory card. If inserting or removing the
SD/SDHC memory card with the power on, the camera will automatically turn off.
Charging the Battery
The battery is not fully charged at the time of purchase. Before use, be sure to charge
the battery until the status LED lights red.
1. Connect camera to AC/DC adapter with USB cable.
2. Insert the plug into a wall outlet.
The status LED blinks red when charging has started and
lights red when charging is completed.
If the status LED does not light, the camera is not
correctly connected or the battery, camera or AC/DC
adapter may be damaged.
Charging time varies according to the ambient temperature and the status of
battery.
The included AC/DC adapter differs depending on the region where you purchased the camera.
User can also charge the battery by connecting camera to computer with USB cable.
1
2
EN-12
Initial Settings
Setting the Date and Time
The date/time needs to be set if and when:
The camera is turned on for the first time.
The camera is turned on after leaving the camera without the battery for an
extended period of time.
When the date and time information is not displayed on the LCD monitor, follow these
steps to set the correct date and time.
1. Press the
MODE button, and set the camera
mode to [ ] or [ ]; or press the 7
button
.
2. Press the
MENU button.
3. Select the [Setup] at the end of the Menu with
the c / d buttons, and press the
SET button.
4. Select [Date/Time] with the c / d buttons, and
press the
SET button.
5. Select the date format with the c / d buttons,
and press the SET button.
Select the item’s field with the e / f buttons
and adjust the value for the date and time
with the c / d buttons.
The time is displayed in 24-hour format.
After confirming all settings are correct, press
the SET button
.
6. To exit from the [Setup] menu, press the MENU
button.
; ;
;;
Off
EN-13
Choosing the Language
Specify in which language menus and messages are to be displayed on the LCD monitor.
1.
Press the MODE button, and set the camera
mode to [ ] or [ ]; or press the 7
button
.
2. Press the
MENU button.
3. Select the [Setup] at the end of the Menu with the
c / d buttons, and press the
SET button.
4. Select [Language] with the
c
/
d
buttons and press
the SET button
.
5. Select the displayed language with the e / f / c
/ d buttons and press the
SET button.
The setting will be stored.
6. To exit from the [Setup] menu, press the
MENU button.
Formatting the Memory Card or Internal Memory
This utility formats the memory card (or internal memory) and erases all stored images
and data.
1. Press the
MODE button, and set the camera
mode to [ ] or [ ]; or press the 7
button
.
2. Press the
MENU button.
3. Select the [Setup] at the end of the Menu with
the c / d buttons, and press the
SET button.
4. Select [Format] with the
c
/
d
buttons, then
press
the SET button
.
5. Select [Execute] with the
e / f
buttons, and
press
the SET button
.
To cancel formatting, select [Cancel] and
press
the SET button
.
6. To exit from the [Setup] menu, press the MENU
button.
;;
;;
;;
EN-14
CAPTURE MODE
Capturing Images
Your camera is equipped with a 2.36” full colour TFT LCD monitor to help you compose
images, playback recorded images/video clips or adjust menu settings.
1. Press the
ON/OFF button to turn the power on.
2. Press the
MODE button, and set the camera mode to [ ].
3. Compose your image in the LCD monitor.
Turn the zoom lever to side to zoom in on the subject, and enlarges the
subject on the LCD monitor.
Turn the zoom lever to side to zoom out on the subject, and provides a wider
angle image.
4. Press the shutter button.
Pressing the shutter button down halfway
automatically focuses and adjusts the
exposure, and pressing the shutter button
down fully captures the image.
The focus area frame turns green when
the camera is in focus and the exposure is
calculated.
When the focus is not suitable, the frame
of the focus area turns red.
EN-15
Setting the Scene Mode
By simply selecting one of the available scene modes, you can capture the image with
the most appropriate settings.
1. Press the
MODE
button, and set the camera mode to [ ], and press the
SET
button.
2. Select the desired scene mode with the e / f /
c / d buttons, and press the
SET button.
3. Compose the image and press the shutter
button.
The table below will help you choose the appropriate scene mode:
Scene mode Description
Auto Select this mode when you want to capture images without
having to set special functions or manual adjustments.
Intelligent Scene Select this mode when you want the camera to select an ideal
shooting mode according to environmentautomatically.
Smile Detection Select this mode to automatically capture an image when a smiling
face is detected.
Anti-shake This mode minimizes the influences of hand shaking when you want
to capture an image.
Panorama Select this mode when you want to capture a series of shots then
stitch them together with software to make a single photo on the
computer.
Portrait Man Select this mode when you want to capture an image that makes a
man stand out against a blurred background.
Portrait Lady Select this mode when you want to capture an image that makes a
lady stand out against a blurred background.
Landscape Select this mode when you want to capture an image with infinity
focus, hard sharpness and high saturation.
Sports Select this mode when you want to capture fast-moving subjects.
Night Portrait Select this mode when you want to capture people with an evening
or night scene background.
Night Scene Select this mode when you want to capture dark scenes such as
night views.
Candlelight Select this mode when you want to capture photos of candlelight
scene, without spoiling the ambience.
;;
EN-16
Taking Images with Intelligent Scene mode
In this Intelligent Scene mode, the camera can sense the ambient conditions and
automatically select the ideal shooting mode.
1. Press the
MODE
button, and set the camera mode to [ ], and press the
SET
button.
2. Select [Intelligent Scene] with the e / f / c / d buttons, and press the SET button.
The camera can automatically select best mode for the shooting scene from
[Auto] / [Landscape] / [
Night Portrait
] / [
Sports
] / [
Portrait Man
] / [Macro].
3. Compose the image, and press the shutter button down fully.
Fireworks Select this mode when you want to capture fireworks clearly with
optimal exposure. The shutter speed becomes slower, so using a
tripod is recommended.
Text Select this mode when you want to capture an image that contains
black and white subjects like printed documents.
Sunset Select this mode when you want to capture a sunset. This mode
helps keep the deep hues in the scene.
Sunrise Select this mode when you want to capture a sunrise. This mode
helps keep the deep hues in the scene.
Splash Water Select this mode when you want to capture photos of splashing
water.
Flow Water Select this mode when you want to capture the soft flowing water.
Snow Select this mode when you want to capture clear snow scenes
without darkened subjects and bluish tint.
Beach Select this mode when you want to capture bright beach scenes
and sunlit water surfaces.
Pets Select this mode when you want to capture your pets. Shoot from
their eye level.
Natural Green Select this mode when you want to capture the green scenery
background such as forest. This mode helps to brighten the
colours.
Program AE This mode allows you to manually set parameters other than the
shutter speed and the aperture value.
Scene mode Description
EN-17
Setting the Panorama Mode
This mode is designed to make it easier to take a series of shots then stitch them
together with software to make a single image. You can capture a photographic subject
that won’t fit into a single frame, such as a landscape, and stitch it together later with a
program such as Arcsoft Panorama Maker
®
4.0 application.
1. Press the
MODE
button, and set the camera mode to [ ], and press the
SET
button.
2. Select [Panorama] with the e / f / c / d buttons, and press the SET button.
3. Select the photographic direction with the e / f buttons.
4. Shoot the first image.
The next image appears beside the previous image.
5. Orient the camera so that the second frame overlaps a small portion of the
photographic subject of the first image and press the shutter button to capture the
next image.
6. Follow the same steps to capture subsequent images in the sequence.
7. Finish the sequence by pressing the
MENU button or switch to another mode after
the last image has been recorded.
Taking Images When the Smile Feature Is On
With the camera’s new “smile detection” function, this camera detects smiles so you
do not miss those special moments in life.
1. Press the
MODE
button, and set the camera mode to [ ], and press the
SET
button.
2. Select [Smile Detection] with the e / f / c / d buttons, and press the SET button.
3. Compose the image, and press the shutter button
down fully.
4. Once the camera detects a smile, it will
automatically capture 3 images (by default, the flash
mode setting is set to
d).
If the [Capture Md.] is set to [Single], the camera
will only capture an image after it detects a
smile.
When capturing group shots (if the number of
people is more than 1), the camera will
automatically capture the image(s) when it
detects two smiles.
If the camera does not detect a smile within 5
seconds, the camera returns to preview display.
Press the shutter button once again to reactivate
this function.
00214
00214
00214
EN-18
Recording Shots using Face Detection Technology
Face Detection Technology can identify and focus on the human faces in the image.
1. Press the
MODE button, and set the camera mode to [ ].
2. Press the button, and select [ ] icon with the e / f buttons. Press the
SET
button.
With Face Detection turned on, the camera identifies main face (white frame)
and subsidiary faces (gray frames).
If the camera cannot detect and track any faces, there will be no frame shown on
the screen.
3. Press the shutter button halfway down to lock the focus.
When the main face is in focus, the white frame
simultaneously turns green. Otherwise, it turns red.
4. Press the shutter button down fully to capture your
image.
Subjects that are not suitable with this function:
a. A person is wearing glasses, sunglasses, or face is covered with hat or hair.
b. A person turns sideways.
Self-portrait Function
Use this function to take pictures of yourself or include yourself in pictures.
1. Press the
MODE button, and set the camera mode to [ ].
2. Press the
e
button, and select [ ] icon with the e / f buttons. Press the SET
button.
3. Press the shutter button.
4. If the camera detect and track any faces, after twice blinking of the self-timer LED,
one image will be captured.
Press the shutter button to exit.
If it does not detect any face within 30 seconds, the camera will automatically
capture an image and return to preview display.
Select [ ] to reactivate this function.
Focus lock
EN-19
VIDEO MODE
Recording Video Clips
This mode allows you to record video clips at a resolution of 320 x 240 / 640 x 480 /
720p pixels.
1. Press the
MODE button, and set the camera mode to [ ].
2. Compose the image.
3. Press the shutter button.
The recording of the video clip will start.
Pressing the shutter button one more time will end the
recording of the video clip.
The recording time depends on the storage size and
the subject of the image to be recorded.
The zoom function cannot be used during video
recording.
When recording a video clip, the flash and "10+2 sec." self-timer function cannot be used.
If the write speed of your SD/SDHC memory card is not fast enough for recording video clips in
the!currently selected quality, the video recording will stop. In this case, select a video quality
lower than the current one.
Playing Back Video Clips
You can play back recorded video clips on the camera.
1. Press the 7 button.
The last image appears on the screen.
2. Select the desired video clip with the e / f buttons.
3. Press the SET button.
A press of the f / e buttons during playback allows fast forward play / fast
reverse play.
To stop video playback, press the d button.
This stops playback and returns to the start of the video clip.
To pause video playback, press the
SET button.
This pauses video playback.
To cancel pause, press the
SET button again.
Video clips cannot be displayed rotated or enlarged.
You cannot play sounds because the camera does not support the speaker function. Please use
PC or other media to play the videos with sounds.
Windows Media player or QuickTime Player is recommended to play back the video clip on your
computer.
QuickTime Player is a free media player available at www.apple.com; and compatible with Mac
and Windows computers.
For more information about the operation of the media player, refer to its respective help
documentation.
EN-20
PLAYBACK MODE
Playing Back Still Images
You can play back the still images on the LCD monitor.
1. Press the 7 button.
The last image appears on the screen.
2. The images can be displayed in forward or reverse
sequence with the e / f buttons.
To view the previous image, press the e button.
To view the next image, press the f button.
Turn the zoom lever to side enlarges the
image.
To return to normal magnification, turn the zoom
lever to side.
An [ ] icon is displayed with the video data. Video clips cannot be rotated.
Playback Display
This function allows you to search quickly for the image that you want and playback
images on the LCD monitor sequentially.
1. Press the 7 button.
The last image appears on the screen.
2. Press the c button to display the next 10th image.
If the 1st image taken is displayed, press the c
button to playback the 11th image taken. Press
the c button again to playback the 21th image
taken and so forth.
3. Press the d button to display the previous 10th
image.
4. Press and hold the
e
/
f
buttons to display the
previous or next images automatically in sequential order.
Release the
e
/
f
buttons if you wish to stop the automatic playback.
If the total number of images is less than 10, press the d button jumps to the first image and
press the c button jumps to the last image.
Video clips will be displayed with an [ ] icon.
110-0201
110-0201
110-0201
2
2
EN-21
Removing Red-eye
You can use this function to remove the red-eye effect after an image is taken.
1. Press the 7 button.
The last image appears on the screen.
2. Select the image that you want to edit with the
e
/
f
buttons.
3. Press the
MENU button.
4. Select [Fix Red Eyes] with the c / d buttons,
and press the
SET button.
5. Select [Execute] with the e / f buttons, and
press the
SET button.
6. View the changes on the corrected image.
7. To save your corrected image, select [Confirm]
with the e / f buttons, and press the
SET
button.
When this process ends, this replaces the
original image with the corrected image.
Dynamic Lighting Feature
This feature compensates for the unfavorable lighting conditions by brightening
underexposed areas and balancing overexposed areas.
1. Press the 7 button.
The last image appears on the screen.
2. Select the image that you want to edit with the
e
/
f
buttons.
3. Press the
MENU button.
4. Select [Dynam. Light.] with the c / d buttons, and
press the
SET button.
5. Select [High] or [Low] with the e / f buttons, and
press the
SET button.
6. View the changes on the corrected image.
7. To save your corrected image, select [Confirm] with
the e / f buttons, and press the
SET button.
When this process ends, this replaces the
original image with the corrected image.
;;
;;
;;
;;
EN-22
Protecting Images
Set the data to read-only to prevent images from being erased by mistake.
1. Press the 7 button.
The last image appears on the screen.
2. Select the image that you want to protect with the e /
f buttons.
3. Press the
MENU button.
4. Select [Protect] with the c / d buttons, and press the
SET button.
5. Select [Single] or [All] with the e / f buttons, and
press
SET button.
6. Select [Set] with the e / f buttons, and press the
SET button.
Protection is applied to the image and the camera
returns to the playback mode.
The protect icon [ ] is displayed with protected
images.
When [All] has been selected,
[]
is displayed
with all the images.
Canceling the Protection
To cancel protection for only one image, display the
image on which you want to remove the image
protection.
1. Press the 7 button.
The last image appears on the screen.
2. Select the image that you want to cancel protection with the e / f buttons.
3. Press the
MENU button.
4. Select [Protect] with the c / d buttons, and press the
SET button.
5. Select [Single] or [All] with the e / f buttons, and press the
SET button.
6. Select [Cancel Protect] with the e / f buttons, and press the
SET button.
The removal of image protection is executed and the camera returns to the
playback mode.
Formatting an SD/SDHC memory card overrides protection, and erases all images regardless of
their protected status.
Date/Time
Setup
2010.01.01
Language
English
Auto Off
Off
;;
;;
MENU SET
;;
EN-23
DPOF Settings
DPOF is the abbreviation for Digital Print Order Format, which allows you to embed
printing information on your memory card. You can select the images to be printed and
how many prints to make with the DPOF menu in the camera and insert the memory
card to the card compatible printer. When the printer starts printing, it will read the
embedded information on the memory card and print the specified images.
1. Press the 7 button.
The last image appears on the screen.
2. Select the image that you want to set DPOF with the
e / f buttons.
3. Press the
MENU button.
4. Select [DPOF] with the c / d buttons, and press the
SET button.
The DPOF setting screen is displayed.
5. Select [Single] or [All] with the e / f buttons, and
press the
SET button.
[Single]: Sets DPOF for each individual image.
[All]: Sets DPOF for all images at once.
6. Select [Print Num.] with the c / d buttons, and
press the
SET button.
This displays the number of prints setting screen.
7. Set the number of prints with the e / f buttons, and
press the
SET button.
8. Select [Date Print] with the c / d buttons, and press
the
SET button.
The date setting screen appears.
9. Select date to [On] or [Off] with the e / f buttons,
and press the
SET button.
[On]: The date of the image will also be printed.
[Off]: The date of the image will not be printed.
The DPOF icon [ ] is displayed on each image
that has set up DPOF settings.
The date that is printed on the image is the date set on the camera. To print the correct date on
the image, set the date on the camera before you capture the image. Refer to the section in this
manual titled “Setting the Date and Time” for further details.
MENU SET
;
DPOF
0
MENU SET
; ;
MENU SET
;;
110-0201
110-0201
110-0201
2
2
EN-24
Erasing Images
Erasing a single image / Erasing all images
1. Press the 7 button.
The last image appears on the screen.
2. Select the image you want to erase with the
e
/
f
buttons.
3. Press the MENU button.
4. Select [Delete] with the c / d buttons, and
press the
SET button.
5. Select [Single] or [All] with the e / f buttons,
and press the
SET button.
[Single]: Erases the selected image or the
last image.
[All]: Erases all of the images except for the
protected images.
6. Select [Execute] with the e / f buttons, and
press the
SET button.
To not erase, select [Cancel], and press the
SET button.
7. To exit from the menu, press the
MENU button.
Deleting an image will not affect sequential image numbering. For example, if you delete image
number 240, the next captured image will be numbered 241 even though 240 no longer exists. In
other words, an image-number is retired when an image is deleted and will not be reused or
reassigned to another subsequently captured image.
;;
MENU SET
;;
EN-25
MENU OPTIONS
Capture Menu
This menu is for the basic settings to be used when capturing still images.
1. Press the
ON/OFF button to turn the power on.
2. Press the
MODE button, and set the camera mode to any scene mode.
3.
Press the MENU button to enter the [Capture] menu.
4. Select the desired option item with the c / d buttons, and press the
SET button to
enter its respective menu.
The selectable items may vary in different capture modes.
5. Select the desired setting with the e / f buttons, and press the
SET button.
6. To exit from the menu, press the
MENU button.
Size
This sets the size of the image that will be captured.
* 12M / 8M / 4M / 2M / VGA
ISO
This sets the sensitivity for capturing images. When the sensitivity is raised (and the
ISO figure is increased), photography will become possible even in dark locations, but
the more pixelated (grainier) the image will appear.
* Auto / ISO100 / ISO 200 / ISO 400 / ISO 800 / ISO 1600
Quality
This sets the quality (compression) at which the image is captured.
* Fine / Standard / Economy
W. Balance
This sets the white balance for a variety of lighting conditions and permits images to be
captured that approach the conditions that are seen by the human eye.
*Auto / Incand. / Fluoresc.1 / Fluoresc.2 / Daylight / Cloudy / Manual WB
Sharpness
This sets the sharpness of the image that will be captured.
* Hard / Standard / Soft
Color
This sets the colour of the image that will be captured.
* Standard / Vivid / Sepia / B&W / Blue / Red / Green / Yellow / Purple
Saturation
This sets the saturation of the image that will be captured.
* High / Standard / Low
MENU SET
;;
MP
4
AUTO
MENU SET
;;
EN-26
Metering
This sets the metering method for calculating the exposure.
Capture Md.
This sets the recording method at the time of capturing images
.
Quick Shot
If this function is set to “On”, the camera takes a quick shot without focusing.
* On / Off
Digi. Zoom
This sets whether or not to use digital zoom at the time of photography.
* On / Off
Preview
This sets whether or not to display the captured image on the screen immediately after
the image is captured.
* On / Off
Date Print
The date of recording can be printed directly on the still images. This function must be
activated before the image is captured.
* On / Off
Setup
Refer to the section in this manual titled “Setup Menu” for further details.
* Center: Averages the light metered from the entire frame, but gives greater weight to
the subject matter at the center.
* Spot: A very small portion of the center of the screen is measured to calculate the
correct exposure.
* Average: The exposure is measured all of the image area.
* Single: Captures one image at a time.
* Continuous: Permits continuous capture of up to 3 images.
* AEB: Permits 3 consecutive images in the order of standard exposure,
underexposure and overexposure compensation.
* Album Shot: Creates an album-like layout to combine 3 shots into a single image.
* Burst: Permits continuous photography while pressing and holding the
shutter button. As long as you hold the shutter button pressed,
images are captured until the memory capacity is exhausted.
* Cont.flash: Permits continuous capture of up to 3 images with flash.
*
Pre-shot: Lets you capture the background first, then have someone to capture
you in front of it.
* Coupl.shot: Uses separate areas to combine two shots. You can include yourself
in the shot.
* Burst 30fps Permits continuous capture of up to 30 images in the resolution 640
x480 within 1 second.
EN-27
Video Menu
This menu is for the basic settings to be used when recording video clips.
1. Press the
MODE button, and set the camera mode to [ ].
2. Press the
MENU button to enter the [Video] menu.
3. Select the desired option item with the c / d buttons, and press the
SET button to
enter its respective menu.
4. Select the desired setting with the e / f buttons, and press the
SET button.
5. To exit from the menu, press the
MENU button.
Size
This sets the size of the video clip that will be captured.
* HD / VGA / QVGA
Quality
This sets the quality (compression) at which the video clip is captured.
* Fine / Standard
Color
This sets the colour of the video clip that will be captured.
* Standard / Vivid / Sepia / B&W / Blue / Red / Green / Yellow / Purple
Audio
This sets whether or not to record audio at the time of video recording.
* On / Off
Digi. Zoom
Refer to the section in this manual titled “Digi. Zoom” in Capture Menu for further details.
Setup
Refer to the section in this manual titled “Setup Menu” for further details.
MENU SET
;;
MENU SET
;;
EN-28
Playback Menu
In the [7] mode, choose which settings are to be used for playback.
1. Press the 7
button
.
2. Press the
MENU button.
3. Select the desired option item with the c / d buttons, and press the
SET button to
enter its respective menu.
4. Select the desired setting with the e / f buttons, and press the
SET button.
5. To exit from the menu, press the
MENU button.
Delete
Refer to the section in this manual titled “Erasing Images” for further details.
Fix Red Eyes
Refer to the section in this manual titled “Removing Red-eye” for further details.
Dynam. Light.
Refer to the section in this manual titled “Dynamic Lighting Feature” for further details.
Slide Show
This function enables you to play back your still images automatically in order one
image at a time.
* 3 Sec./5 Sec./10 Sec.
Rotate
If you wish to rotate a still image 90 degrees to the right, select +90°; if you wish to
rotate it 90 degrees to the left, select -90°. Video clips cannot be rotated.
* +90° / -90°
DPOF
Refer to the section in this manual titled “DPOF Settings” for further details.
Protect
Refer to the section in this manual titled “Protecting Images” for further details.
Resize
Resizes a previously saved image. Resizing replaces the original image with the
changed image. It is only possible to resize to a smaller size.
MENU SET
;;
;;
EN-29
Qual. Change
Changes the quality (compression) of a recorded image. Compress images down to half
of their size or less, overwrite old size images with newly compressed images. It is only
possible to reduce the image quality/size, never to increase it.
Copy to Card
Allows you to copy your files from the camera’s internal memory to an SD/SDHC
memory card. Of course, you can only do this if you have a memory card installed and
some files in internal memory. All files remain in the internal memory, even after copy to
the SD/SDHC memory card from the internal memory.
* Cancel / Execute
Setup
Refer to the section in this manual titled “Setup Menu” for further details.
EN-30
Setup Menu
Set your camera’s operating environment.
1. Press the
MODE button, and set the camera mode to [ ] or [ ]; or press the 7
button.
2. Press the MENU button.
3. Select the [Setup] at the end of the Menu with the c / d buttons, and press the
SET
button.
4. Select the desired option item with the c / d buttons, and press the
SET button to
enter its respective menu.
5. Select the desired setting with the e / f buttons, and press the
SET button.
6. To exit from the menu, press the
MENU button.
Date/Time
Refer to the section in this manual titled “Setting the Date and Time” for further details.
Language
Refer to the section in this manual titled “Choosing the Language” for further details
.
Auto Off
If no operation is performed for a specific period of time, the power to the camera is
automatically turned off. This feature is useful for reducing battery usage.
* 1 Min. / 2 Min. / 3 Min. / Off
Beep
This sets whether or not to mute the camera sound each time you press the camera's
buttons.
* On / Off
Display
This sets the image information display state.
* Default / All / Off
Video Out
This sets your camera to match the system of the equipment that you are going to
connect to the camera.
* NTSC / PAL
;;
Off
MENU SET
;;
EN-31
Fr. No. Reset
This creates a new folder. The captured images are recorded to the newly created
folder from number 0001.
* Cancel / Execute
LCD Bright.
Select a brightness level for the LCD monitor.
* Standard / Bright
Format
Refer to section in this manual titled “Formatting the Memory Card or Internal Memory”
for further details.
Media Info.
This displays the free capacity of the internal memory or the memory card.
Sys. Info.
This displays the firmware version of the camera.
Sys. Reset
This returns all basic settings to the camera’s default settings.
* Cancel / Execute
EN-32
TRANSFERRING FILES TO YOUR COMPUTER
System Requirement
Downloading Your Files
1.
Turn on your camera.
2.
Connect the camera to your computer with the USB cable
.
3. Select [PC] using the
c
/
d
buttons and press the
SET
button.
4.
From the Windows desktop, double click on “My Computer”
.
5. Look for a new “removable disk” icon.
6. Double click on the removable disk and locate the DCIM folder.
Your recorded images and video clips will be inside the
folders of DCIM folder.
Copy&Paste or Drag-N-Drop image and video files to a folder on your computer.
Mac users:
Double-click the “untitled” or “unlabeled” disk drive icon on your desktop.
iPhoto may automatically launch.
USING THE CAMERA AS A PC CAMERA
Your camera can act as a PC camera, which allows you to videoconference with
business associates, or have a real-time conversation with friends or family. Your
computer system must include the items, Microphone, Sound card, Speakers or
headphones, Network or Internet connection.
Using the camera as a PC camera, Service Pack 3 is suggested to the users of Windows XP,
Service Pack 3 can be downloaded by visiting http://WWW.microsoft.com/.
Windows Macintosh
Pentium III 1GHz or equivalent
Windows 7/XP/Vista
512MB RAM
150MB available hard disk space
CD-ROM drive
Available USB port
PowerPC G3/G4/G5
OS 10.3.9 or later
256MB RAM (512 MB recommended)
128MB available hard disk space
CD-ROM drive
Available USB port
EN-33
EDITING SOFTWARE INSTALLATION
There are 3 types of software that are included on the CD-ROM:
ArcSoft MediaImpression™ - manages your media for you, and gives you tons of fun
and exciting ways to create and share projects featuring your photo, video, and music
files. Create your own movies or photo slide shows, complete with soundtrack; edit,
enhance, and add fun creative effects to your photos; and share your files easily
through simple email attachments or popular photo printing and video sharing websites.
Print Creations - brings you a family of fun and easy print-project software that brings
out the creativity in you. You can personalize the designs with your own digital pictures
and text based on professionally designed templates and layouts. Projects can be
printed at home or saved as image files for sharing with family and friends by email or
the web.
Arcsoft Panorama Maker
®
4.0 - Like magic, ArcSoft Panorama Maker
®
4 turns any
series of overlapping photos into a gorgeous panoramic image in just seconds. The
program does most of the work for you by automatically selecting an entire group of
pictures with one click, automatically organizing the photos into the proper order, then
seamlessly stitching the photos into a panoramic masterpiece that you can print, share
or post to the web. Create horizontal, vertical and 360° panorama pictures all within this
one amazing program.
To install software:
1. Insert the CD-ROM that came with the camera into your CD-ROM drive.
The welcome screen appears.
2. Click the respective software name.
Follow the on-screen instructions to complete the installation.
For more information about the operation of the software, refer to its respective help documentation.
For Windows 7/XP/Vista users, please make sure to install and use the software in “Administrator”
mode.
The software is not supported by Mac.
EN-34
SPECIFICATIONS
* Design and specifications are subject to change without notice.
Item Description
Image sensor 1/2.33” CCD sensor (12.0 megapixels)
Image resolution
Still image
12M (3968X2976), 8M(3264 x 2448) ,4M (2304x1728), 2M(1600
x 1200) ,VGA(640 x 480)
Video clip
VGA(640x480)/30fps, QVGA(320x240)/30fps, HD(720p)/30fps
LCD monitor 2.36” full colour TFT LCD (112K pixels)
Recording media
32MB internal memory (10MB available for image storage)
Supports SD/SDHC memory card (up to 16GB) (optional)
File format
DCF, JPEG (EXIF 2.2), DPOF, Motion-JPEG (AVI), HD720p/
30fps
Lens
3x optical zoom lens
Aperture range: 3.1(W) - 5.9(T)
Focal length: 6.3mm - 18.9mm
Focus Range
Macro: 0.2m~Inf.(W) 0.6m~Inf (T)
Normal: 0.6m~Inf (W) 1m~Inf (T)
Shutter speed 4~1/2000 Sec.
Digital zoom
6x (Capture mode)
4x (Playback mode)
Terminals
USBAV OUT
(2 in 1 terminal)
Power supply Rechargeable Lithium-ion battery (3.7V)
BatteryCharging
environment
Temperature
0
°C - 40°C(32°F to 104°F)(Charging)
Dimensions
Approx. 95 x 59.7 x 22.6mm (without protruding parts)
Weight Approx. 104g (without battery and memory card)
EN-35
APPENDIX
Possible Number of Shots
Possible number of shots (still image)
The table shows the approximate shots that you can capture at each setting based on
the capacity of the internal memory and the SD/SDHC memory card.
Possible recording time / sec (video clip)
* We recommend a memory card of at least 10MB/Sec write speed to prevent auto stop or
unexpected results. If you experience an error using a slower SD/SDHC memory card, you
can set your camera’s video recording to QVGA (320 x 240) and standard quality.
Size Quality
SD/SDHC memory card capacity
1GB 2GB
4GB
SDHC
8GB
SDHC
16GB
SDHC
3968 x 2976
Fine
170 331 682 1370 2675
Standard
321 623 1282 2575 5025
!
Economy
398 772 1589 3190 6227
3264 x 2448
Fine
244 474 978 1963 3832
Standard
453 877 1805 3623 7072
!
Economy
560 1082 2228 4473 8729
2304 x 1728
Fine
592 1143 2354 4275 9221
Standard
928 1782 3667 7360 14362
!
Economy
1156 2212 4551 9134 17824
1600 x 1200
Fine
1303 2487 5118 10272 20045
Standard
2066 3896 8015 16085 31389
!
Economy
2452 4597 9457 18979 37035
x
640 x 480
Fine
5511 9856 20276 40689 79397
Standard
12292 19974 41090 82457 99998
!
Economy
12268 19974 41090 82457 99998
Size Quality
SD/SDHC
memory card capacity
1GB 2GB
4GB
SDHC
8GB
SDHC
16GB
SDHC
HD
1280 x 720
Fine 00:06:22 00:12:24 00:25:32 00:51:15 01:40:00
Standard 00:06:31 00:12:42 00:26:08 00:52:27 01:42:22
x
640 x 480
Fine 00:08:43 00:16:58 00:34:35 01:10:05 02:16:45
Standard 00:09:58 00:19:25 00:39:57 01:20:11 02:36:27
320 x 240
Fine 00:26:38 00:51:53 01:46:45 03:34:13 06:57:59
Standard 00:32:47 01:03:51 02:11:21 04:23:35 08:34:20
EN-36
Troubleshooting
Refer to the symptoms and solutions listed below before sending the camera for repairs.
If the problem persists, contact your local reseller or service center.
Symptom Cause Solutions / Corrective Actions
The power does not come
on.
The battery is not inserted. Insert the battery correctly.
The battery is exhausted. Recharge the battery.
The battery runs out quickly. The battery is not fully charged.
The battery is not used for an
extended period of time after
being charged.
Fully charge the battery and
discharge it for at least one
complete cycle before use to
maximize its performance and
lifetime.
The battery or camera feels
warm.
Long period of continuous use of
the camera or the flash.
Even if press the shutter
button, the camera does not
take a picture.
The shutter button is not pressed
all the way down.
Press the shutter button all the
way down.
The memory card does not have
any free capacity.
Insert a new memory card, or
delete unwanted files.
The memory card is
write-protected.
Remove the write-protection.
Images do not appear on
the LCD monitor.
LCD monitor is dark. Adjust the brightness of the
LCD monitor in the menu.
Although it is set to auto
focus, it does not focus.
The lens is dirty. Wipe clean with a soft, dry cloth
or lens paper.
The distance to the subject is
smaller than the effective range.
Get your subject within the effective
focus range.
The contents on the
memory card cannot be
played back.
You played back a memory card
that was not formatted by this
camera
.
Insert a memory card that was
formatted on this camera.
Files cannot be deleted. The file is protected. Cancel protection.
The memory card is
write-protected.
Remove the write-protection.
Even when the camera’s
buttons are pressed, it does
not operate.
The battery is running low. Recharge the battery.
The date and time are
wrong.
The correct date and time is not
set.
Set the correct date and time.
Cannot download images. The free space on the hard disk
in your computer may be
insufficient.
Check whether the hard disk has
space for running Windows, and
if the drive for loading image files
has a capacity at least that of the
memory card inserted in the camera.
No power supply. Recharge the battery.
noitanalpxeEEEWegaugnaL
English
French
German
The mark is in compliance with the Waste Electrical and Electronic Equipment Directive
2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment including any spent or
discarded batteries as unsorted municipal waste, but use the return and collection systems
available. If the batteries or accumulators included with this equipment, display the chemical
symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than
0.0005% Mercury, or more than 0.002% Cadmium or more than, 0.004% Lead.
Le marquage est en conformité avec la directive 2002/96/EC du DEEE (déchets d’équipements
électriques et électroniques).
Ce symbole indique l'obligation de ne pas déposer ce produit, y compris les batteries et
accumulateurs vides ou déchargés, dans des décharges publiques, mais d'utiliser les systèmes
spécifiques de retour et récupération disponibles.
Si sur les piles ou accumulateurs inclus avec cet appareil, le symbole chimique Hg, Cd ou Pb
est visible, cela signifie que la batterie a une teneur en métaux lourds de plus de 0.0005% de
mercure, ou plus de 0,002% de cadmium, ou plus de 0,004 % Plomb.
Das Symbol ist in Übereinstimmung mit der Richtlinie 2002/96/EG über Elektro- und Elektronik
Altgeräte (EAG-Richtlinie).
Das Symbol weist darauf hin, dass das Gerät einschließlich ge- und verbrauchten Batterien bzw
Akkus nicht in den Hausmüll entsorgt werden darf, sondern den hierfür bestimmten Sammelsys-
temen zugeführt werden muss. Falls die mit diesem Gerät gelieferten Batterien oder Akkus das
chemische Zeichen Hg, Cd oder Pb zeigen bedeutet das die Batterien oder Akkus ein
Schwermetall-Anteil von mehr als 0.0005% Quecksibler (Hg) , oder mehr als 0.002% Kadmium
(Cd) oder mehr als 0.004% Blei (Pb) haben.
Spanish
El símbolo es un requisito de la Directiva europea 2002/96/EC (WEEE) acerca de los Residuos
de Aparatos Eléctricos y Electrónicos. (RAEE)
Este símbolo indica la obligación de no mezclar ni los aparatos señalizados, ni las baterias ya
gastadas o desechadas, con los residuos domésticos generales, sinó que deben utilizarse los
sistemas de recogida específicos, disponibles para estos productos. Si en las baterías o
cargadores incluidos en este equipo aparecen los símbolos químicos Hg, Cd o Pb, se indica
que contienen metales pesantes en cantidades superiores a 0,0005% de Mercurio, o a 0,002%
de Cadmio, o a 0,004% de plomo respectivamente.
Märket anger överensstämmelse med Waste Electrical and Electronic Equipment Directive
2002/96/EC (WEEE).
Märket anger kravet på att använda tillgängliga retur- och insamlingssystem och att EJ avyttra
utrustningen, inkluderat förbukade eller kasserade batterier, som osorterat kommunalt avfall.
Om batterierna eller accumulatorerna som är inkluderade i produkter är märkta med de kemisla
symbolerna Hg, Cd eller Pb, anger det att de innehåller tungmetaller, med mer än 0,0005%
kvicksilver, eller mer än 0,002%.
Italian
Swedish
Il simbolo è in accordo con la Direttiva 2002/96 EC sui Rifiuti Apparecchiature Elettriche ed
Elettroniche (RAEE).
Il simbolo indica l' obbligo della raccolta separata delle apparecchiature elettriche ed
elettroniche, incluse le batterie scariche o esaurite, pertanto si raccomanda d'utilizzare i sistemi
di raccolta e/o restituzione disponibili nella vostra zona per queste tipologie
d'apparecchiature.Se le batterie o gli accumulatori inclusi in questa apparecchiatura recano il
simbolo chimico Hg, Cd o Pb, significa che il loro contenuto di metallo pesante è alto, con una
percentuale di Mercurio superiore a 0.00005%, Cadmio superiore a 0.002% o Piombo superiore
a 0.004%.
noitanalpxeEEEW
egaugnaL
Dutch
Norwegian
Greek
Symbolet er i samsvar med Waste Electrical and Electronic Equipment Directive 2002/96/EC
(WEEE).
Symbolet angir kravet på å anvende tilgjengelige retur og gjenvinningssystem, og ikke benytte
vanlige usorterte kommunale avfallsordninger, dette gjelder òg batterier og akkumulatorer.
Dersom batterier eller akkumulatorer er merket med de kjemiske symbolene Hg, Cd eller Pb,
angir dette at de inneholde tungmetaller, med mer enn 0,0005% kvikksølv, eller mer enn
0,002% kadmium, eller mer enn 0,004% bly.
De markering is in overeenstemming met de Richtlijn 2002 / 96 / EG betreffende afgedankte
elektrische en elektronische apparatuur (AEEA).
De markering is een aanduiding voor de eis de apparatuur, inclusief lege of beschadigde
batterijen, NIET weg te werpen bij het huishoudelijk afval, maar de beschikbare inzamelsyste-
men te gebruiken. Als op de batterijen of accu’s van deze apparatuur de chemische symbolen
Hg, Cd, of Pb staan, betekent dit dat de batterij zware metalen bevat in een concentratie van
meer dan 0,0005% kwik, meer dan 0,002% cadmium of meer dan 0,004% lood.
TRıȪȝȕȠȜȠİȓȞĮȚıȪȝijȦȞȠȝİIJȘȞȅįȘȖȓĮIJȘȢǼȣȡȦʌĮȧțȒȢDzȞȦıȘȢ(&ʌİȡȓ
ǹʌȩȡȡȚȥȘȢǾȜİțIJȡȚțȫȞțĮȚǾȜİțIJȡȠȞȚțȫȞȈȣıțİȣȫȞ:(((
ȉȠıȪȝȕȠȜȠĮȣIJȩȣʌȠįİȚțȞȪİȚIJȘȞȣʌȠȤȡȑȦıȘȞĮȂǾȃĮʌȠȡȡȓʌIJİIJİIJȘȞıȣıțİȣȒțĮșȫȢțĮȚIJȚȢ
ȤȡȘıȚȝȠʌȠȚȘȝȑȞİȢȝʌĮIJĮȡȓİȢıIJȠȣȢțȐįȠȣȢIJȦȞȠȚțȚĮțȫȞĮʌȠȡȡȚȝȝȐIJȦȞĮȜȜȐȞĮ
ȤȡȘıȚȝȠʌȠȚİȓIJİIJȠıȪıIJȘȝĮİʌȚıIJȡȠijȒȢțĮȚʌİȡȚıȣȜȜȠȖȒȢĮȞĮțȪțȜȦıȘȢĮʌȠȡȡȚȝȝȐIJȦȞ
ǹȞȠȚȝʌĮIJĮȡȓİȢijȑȡȠȣȞIJĮıȪȝȕȠȜĮ+J&GȒ3EĮȣIJȩıȘȝĮȓȞİȚȩIJȚȘʌİȡȚİțIJȚțȩIJȘĮIJĮIJȠȣȢıİ
ȕĮȡȑĮȝȑIJĮȜĮȣʌİȡȕĮȓȞİȚIJȠıİȣįȡȐȡȖȣȡȠȒIJȠıİțȐįȝȚȠȒIJȠıİ
ȝȩȜȣȕįȠ´
Danish
Mærket angiver overensstemmelse med direktivet om affald af elektrisk og elektronisk udstyr
2002/96/EF (WEEE).
Mærket angiver kravet om IKKE at bortskaffe udstyret, herunder brugte eller bortkastede
batterier, som usorteret affald fra husholdningen, men i stedet bruge de tilgængelige genbrugs-
og indsamlingssystemer. Hvis batterierne eller akkumulatorerne, der er inkluderet med dette
udstyr, har det kemiske symbol Hg, Cd eller Pb, betyder det, at batterierne har et indhold af
tungmetal på mere end 0,0005 % kviksølv, eller mere end 0,002 % kadmium, eller mere end
0,004 % bly.
=QDþNDMHYVRXODGXV'LUHNWLYRXRQDNOiGiQtV(OHNWUR]DĜt]HQtPi a Eletroodpady 2002/96/EC
(WEEE).
TDWR]QDþNDXUþXMHSRåDGDYHNQHY\KD]RYDWMDNpNROLY]DĜt]HQtNWHUpREVDKXMHSRXåLWpþLY\ELWp
EDWHULHGRNRPXQiOQtKRRGSDGXDOHYUiWLWW\WRQDGRVWXSQiPtVWD]SČWQpKRRGEČUXNROHNWLYQtKR
V\VWpPX3RNXGMHQDEDWHULtFKDDNXPXOiWRUHFKREVDåHQpYWČFKWRYêUREFtFKV\PERO+J&G
QHER3E]QDPHQiWRåHEDWHULHREVDKXMtWČåNpNRY\RREVDKXYtFHQHå5WXWLQHER
YtFHQHå.DGPLDQHERYtFHQHå2ORYD
Finnish
Czech
Tunnus on "Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE) mukainen.
Tunnus tarkoittaa että laitetta, mukaanlukien käytettyjä tai hylättyjä paristoja EI poisteta
lajittelemattomana jätteenä, vaan että käytetään käytettävissä olevia palautus- ja keräysjärjest-
elmiä. Jos laitteessa olevat paristot tai akut on varustettu merkeillä Hg, Cd tai Pb ylittyvät
raskasmetallien määrä seuraavasti; > 0.0005% elohopeaa, > 0.002% kadmiumia tai yli 0.004%
lyijyä.
QSG-1
1
5
243
6
GETTING TO KNOW YOUR CAMERA
Front View
Rear View
Item
Function
Capture Mode Video Mode Playback Mode
1. Shutter button Record button Still image: to capture mode
Video clip: to capture mode
2. :Zooms out :Zooms in :Zooms out :Zooms
in
:Zooms out :Zooms in
3. Switches to:
Video mode > Capture mode
Switches to:
Capture mode > Video mode
Still image: to capture mode
Video clip: to capture mode
4. Focus Focus Next 10th image
5. Compensation s>P -- Previous Image
6. Flash -- Next Image
7. If any scene mode is set:
switches to scene mode
selection screen
--
Still image: to display image
Video clip: to play video clip
8. Self-timer Self-timer Previous 10th image
9. Playback mode Playback mode Still image: to capture mode
Video clip: to capture mode
10. Capture menu Video menu Playback menu
1
A
B
C
D
E
F
3
4
6
8
9
5
7
10
2
A. LCD monitor
B. Status LED
C. Strap holder
D. Battery / Memory card cover
E. Tripod socket
F. USB and AV OUT terminal
1. Shutter button
2. Self-timer LED
3. ON/OFF Power button
4. Flash
5. Microphone
6. Lens
Helpline Number: 08704460806
QSG-2
GETTING STARTED
Preparation
1. Attach the camera strap.
2. Open the battery/memory card cover.
3. Insert the supplied battery with correct orientation as shown. (label side back)
4. Insert an SD/SDHC memory card (Optional).
The camera has
32MB internal me
mory
(10MB available for image storage),
but
you can load an SD/SDHC memory card to expand the camera’s memory capacity.
Be sure to format the memory card with this camera before its initial usage.
5. Close the battery/memory card cover and make sure it is locked securely.
Charging the Battery
The battery is not fully charged at the time of purchase. Before use, be sure to charge
the battery until the status LED lights red.
1. Connect camera to AC/DC adapter with USB cable.
2. Insert the plug into a wall outlet.
The status LED blinks red when charging has started and
lights red when charging is completed.
If the status LED does not light, the camera is not
correctly connected or the battery, camera or AC/DC
adapter may be damaged.
Charging time varies according to the ambient temperature and the status of
battery.
1
2
QSG-3
CAPTURE MODE
Capturing Images
Your camera is equipped with a 2.36” full colour TFT LCD monitor to help you compose
images, playback recorded images/video clips or adjust menu settings.
1. Press the
ON/OFF button to turn the power on.
2. Press the
MODE button, and set the camera mode to [ ].
3. Compose your image in the LCD monitor.
Turn the zoom lever to side to zoom in on the subject, and enlarges the
subject on the LCD monitor.
Turn the zoom lever to side to zoom out on the subject, and provides a wider
angle image.
4. Press the shutter button.
Pressing the shutter button down halfway
automatically focuses and adjusts the
exposure, and pressing the shutter button
down fully captures the image.
The focus area frame turns green when
the camera is in focus and the exposure is
calculated.
When the focus is not suitable, the frame
of the focus area turns red.
QSG-4
VIDEO MODE
Recording Video Clips
This mode allows you to record video clips at a resolution of 320 x 240 / 640 x 480 /
720p pixels.
1. Press the
MODE button, and set the camera mode to [ ].
2. Compose the image.
3. Press the shutter button.
The recording of the video clip will start.
Pressing the shutter button one more time will end the
recording of the video clip.
The recording time depends on the storage size and
the subject of the image to be recorded.
The zoom function cannot be used during video
recording.
Playing Back Video Clips
You can play back recorded video clips on the camera.
1. Press the 7 button.
The last image appears on the screen.
2. Select the desired video clip with the e / f buttons.
3. Press the
SET button.
A press of the f / e buttons during playback allows fast forward play / fast
reverse play.
To stop video playback, press the d button.
This stops playback and returns to the start of the video clip.
To pause video playback, press the
SET button.
This pauses video playback.
To cancel pause, press the
SET button again.
QSG-5
PLAYBACK MODE
Playing Back Still Images
You can play back the still images on the LCD monitor.
1. Press the 7 button.
The last image appears on the screen.
2. The images can be displayed in forward or reverse
sequence with the e / f buttons.
To view the previous image, press the e button.
To view the next image, press the f button.
Turn the zoom lever to side enlarges the
image.
To return to normal magnification, turn the zoom
lever to side.
Playback Display
This function allows you to search quickly for the image that you want and playback
images on the LCD monitor sequentially.
1. Press the 7 button.
The last image appears on the screen.
2. Press the c button to display the next 10th image.
If the 1st image taken is displayed, press the c
button to playback the 11th image taken. Press
the c button again to playback the 21th image
taken and so forth.
3. Press the d button to display the previous 10th
image.
4. Press and hold the
e
/
f
buttons to display the
previous or next images automatically in sequential order.
Release the
e
/
f
buttons if you wish to stop the automatic playback.
110-0201110-0201110-0201
22
QSG-6
Erasing Images
Erasing a single image / Erasing all images
1. Press the 7 button.
The last image appears on the screen.
2. Select the image you want to erase with the
e
/
f
buttons.
3. Press the MENU button.
4. Select [Delete] with the c / d buttons, and
press the
SET button.
5. Select [Single] or [All] with the e / f buttons,
and press the
SET button.
[Single]: Erases the selected image or the
last image.
[All]: Erases all of the images except for the
protected images.
6. Select [Execute] with the e / f buttons, and
press the
SET button.
To not erase, select [Cancel], and press the
SET button.
7. To exit from the menu, press the
MENU button.
;;
MENU SET
;;
QSG-7
TRANSFERRING FILES TO YOUR COMPUTER
System Requirement
Downloading Your Files
1.
Turn on your camera.
2.
Connect the camera to your computer with the USB cable
.
3. Select [PC] using the
c
/
d
buttons and press the
SET
button.
4.
From the Windows desktop, double click on “My Computer”
.
5. Look for a new “removable disk” icon.
6. Double click on the removable disk and locate the DCIM folder.
Your recorded images and video clips will be inside the
folders of DCIM folder.
Copy&Paste or Drag-N-Drop image and video files to a folder on your computer.
Mac users:
Double-click the “untitled” or “unlabeled” disk drive icon on your desktop.
iPhoto may automatically launch.
This symbol mark [crossed-out wheeled bin] indicates separate collec-
tion of waste batteries in the EU countries. The batteries provided with
this product shall not be treated as household waste. Please use the
return and collection systems available in your country for the disposal
of the waste batteries.
If a chemical symbol is printed beneath the symbol mark, this chemical
symbol means that the batteries contains a heavy metal at a certain
concentration. It is indicated as follows:
Hg: mercury, Cd: cadmium, Pb: lead.
Windows Macintosh
Pentium III 1GHz or equivalent
Windows 7/XP/Vista
512MB RAM
150MB available hard disk space
CD-ROM drive
Available USB port
PowerPC G3/G4/G5
OS 10.3.9 or later
256MB RAM (512 MB recommended)
128MB available hard disk space
CD-ROM drive
Available USB port
47

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi HDC-1205E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi HDC-1205E in de taal/talen: Engels als bijlage per email.

De handleiding is 2,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info