566210
10
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
9
English
SPECIFICATIONS
Code CS of model name means Chain saw
Model CS33EDT (30) CS33EDT (35)
Typ e of equipment Chain saw, portable
Engine Size (cm
3
) 32.2
Spark Plug NGK BPMR-7A
Fuel Tan k Capacity (cm
3
)290
Chain Oil Ta nk Capacity (cm
3
)180
Dry Weight (kg)
(Without guide bar and chain)
3.4
Guide bar length (mm) 300 350
Chain pitch (mm) 9.53
Chain gauge (mm) 1.27
Sound pressure level LpA (dB (A)) by ISO 22868
Equivalent
Uncertainty
100
3
Sound power level LwA (dB (A)) by ISO 22868
Measured
Uncertainty
Sound power level LwA (dB (A)) by 2000/14/EC
Measured
Guaranteed
109
3
113
116
Vibration level (m/s
2
) by ISO 22867
Front handle
Rear handle
Uncertainty
4.4
6.1
0.8
Max. engine power by ISO 7293 (kW) 1.3/9300
Max. engine speed (min
-1
) 12000
Idle engine speed (min
-1
) 3000
Speci c fuel consumption (g/kWh) 567
Typ e of chain
91VG045
(Oregon)
91VG052
(Oregon)
Max. chain speed (m/sec) 22.9
Sprocket (number of teeth) 6
NOTE: Equivalent noise level/vibration levels by ISO 22868/22867 are calculated as the time-weighted energy total for noise/vibration levels
under various working conditions with the following time distribution: 1/3 idle, 1/3 full, 1/3 racing speed.
*All
data subject to change without notice.
ASSEMBLY PROCEDURES
WARNING
Never try to start engine without side case, bar and chain
securely fastened.
1. Pull the chain brake (18) toward the front handle to check that the
brake is disengaged. (Fig. 15).
2. Remove guide bar clamp nut (2). Remove the side case (3)
(Fig. 2)
* In
case of installing the spiked bumper (4), install the spiked
bumper (4) to the unit with two screws. (Fig. 3)
3. Install the guide bar (5) onto the bolts (6), then push it toward the
sprocket (7) as far as it will go. (Fig. 4)
4. Con rm the
direction of saw chain (10) is correct as in thegure,
and align the chain on the sprocket. (Fig. 5)
5. Guide the chain drive links into the bar groove all around the bar.
6. Install the side case (3) onto the bolts (6).
Make sure that the boss of chain
tension adjust bolt (8)ts into
the hole of the bar (9). (Fig. 4)
Then tighten the guide bar clamp nut (2) by hand that allows the
chain bar end to move up and down easily.
(
Fig. 2
)
7. Raise the bar end, and tighten the saw chain (10) by turning the
tension adjustment bolt (11) clockwise. To check proper tension,
lightly lift up the center of chain and there should be about 0.5 1.0
mm clearance between bar and edge of drive link (12). (Fig. 6,
7)
CAUTION
PROPER TENSION IS EXTREMELY IMPORTANT
8. Raise the bar end, and securely tighten the guide bar clamp nut
with the combi box spanner. (Fig. 7)
9. A new chain will stretch so adjust the chain after a few cuts and
watch chain tension carefully for therst half hour
of cutting.
NOTE
Check the chain tension frequently for optimum performance
and durability.
CAUTION
When the chain is excessively tightened, the bar and chain will
be damaged rapidly. Conversely, when the chain is excessively
loosened, it may get out of the groove in the bar.
Always wear gloves when touching the
chain.
WARNING
During operation, hold chain sawrmly with both hands. A single
hand operation may cause serious injury.
000Book_CS33EDT_WE.indb 9000Book_CS33EDT_WE.indb 9 2011/08/06 9:14:552011/08/06 9:14:55
10

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Hitachi-CS33EDT

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CS33EDT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CS33EDT in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 15,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info