566209
14
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
14
English
Oiler port (Fig. 31)
Clean the chain oiler port (39) whenever possible.
Guide bar (Fig. 32)
Before using the machine, clean the groove and oiler port (40) in the
bar with the special gauge o ered as an optional accessory.
Side case (Fig. 33)
Always keep the side case and drive area clean of sa
w dust and
debris. Periodically apply oil or grease to this area to protect from
corrosion as some trees contain high levels of acid.
Fuel lter (Fig. 34)
Remove the fuellter from the fuel tank and thoroughly wash it in
solvent. After that, push thelter into the tank comple
tely.
NOTE
If thelter is hard due to dust and dirt, replace it.
Chain oil lter (Fig. 35)
Remove the oillter and thoroughly wash it in solvent.
CHAIN SHARPENING
Parts of a cutter (Fig. 36, 37)
WARNING
Gloves should be used when sharpening chain.
Be sure to round o the front edge to reduce the chance of
kickback or tie-strap breakage.
41. Top plate
42. Working corner
43. Side plate
44. Gullet
45. Heel
46. Chassis
47. Rivet hole
48. To e
49. Depth gauge
50. Correct angle on top plate (degree of angle depends on chain
ty
pe)
51. Slightly protruding “hook” or point (curve on non-chisel chain)
52. Top of depth gauge at correct height below top plate
53. Front of depth gauge rounded o
LOWERING DEPTH GAUGES WITH A FILE
1) If you sharpen your cutters with ale holder, check and lo
wer the
depth.
2) Check depth gauges every third sharpening.
3) Place depth gauge tool on cutter. If depth gauge projects,le
it level with the top of the tool. Alwaysle from the inside of the
chain toward an outside cutter. (Fig. 38)
4) Round o front corner to maint
ain original shape of depth gauge
after using depth gauge tool. Always follow the recommended
depth gauge setting found in the maintenance or operator
manual for your saw. (Fig. 39)
GENERAL INSTRUCTIONS FOR FILING CUTTERS
File (54) cutter on one side of the chain from the inside out. File on
forward strok
e only. (Fig. 40)
5) Keep all cutters the same length. (Fig. 41)
6) File enough to remove any damage to cutting edges (side plate
(55) and top plate (56)) of cutter. (Fig. 42)
SHARPENING ANGLES FOR SHARPENING SAW CHAIN
1. Part Number 91VG
2. Pitch 3/8
3. Depth Gauge Setting 0.025
4. Side Plate Filing Angle 80°
5. Top Plate Angle 30°
6. File Guide Angle 90°
Maintenance schedule
Below you willnd some general maintenance instructions. For
further information please contact HITACHI dealer.
Daily maintenance
Clean the exterior of the unit.
Clean the chain oillter port.
Clean the groove and oillter port in the guide bar.
Clean the side case of sa
w dust.
Check that the saw chain is sharp.
Check that the bar nuts are su ciently tightened.
Make sure that the chain transport guard is undamaged and that
it can be securelytted.
Check that nuts and screws are su ciently tightened.
Especially inspect the bolt of mu er and ensure tha
t they are
properly tightened before starting engine. Should any of the
bolts be loose, retighten them immediately. Failure to do so
could result in serious hazard.
Check the tip of the bar. Please exchange it for the new one
when it is worn out.
Ch
eck the band of chain brake. Please exchange it for the new
one when it is worn out.
Weekly maintenance
Check the starter, especially cord.
Clean the exterior of the spark plug.
Remove the spark plug and check the electrode gap. Adjust it to
0.6 mm or change the spark plug
.
Check that the air intake at the starter is not clogged.
Clean the airlter.
Monthly maintenance
Rinse the fuel tank with gasoline, and clean fuellter.
Clean chain oillter.
Clean the exterior of the carburetor and the space around it.
Quarterly maintenance
Clean the coolingns on the cylinder
.
Clean the fan and the space around it.
Clean the mu er of carbon.
CAUTION
Cleaning of cylinderns, fan and mu er shall be done by a
HITACHI Authorized Service Center.
NOTE
When ordering the parts to your nearest dealer, please use the
item number
s showing on the parts breakdown section in this
instruction.
BAR NO.
LENGTH-
TYPE
NOSE-
TYPE
CHAIN
NO.
(OREGON)
MODEL
NO.
E&S
PO12-50CR
PO14-50CR
PO16-50CR
12
14
16
SPROCKET
SPROCKET
SPROCKET
91VG 045X
91VG 052X
91VG 057X
MODEL
NO.
OREGON
120SDEA041
140SDEA041
160SDEA041
26779
26780
160NDEA041
12
14
16
12
14
16
SPROCKET
SPROCKET
SPROCKET
NON-ARMOR
NON-ARMOR
NON-ARMOR
91VG 045X
91VG 052X
91VG 057X
91VG 045X
91VG 052X
91VG 057X
000Book_CS33EB_WE.indb 14000Book_CS33EB_WE.indb 14 2010/11/30 11:09:312010/11/30 11:09:31
14

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Hitachi-CS33EB

Zoeken resetten

  • Hoeveel slagen moeten de twee diep verzonken benzine./ lucht afstel schroeven van de CS33EB motorkettingzaag met en speciale schroevendraaier open gedraaid worden Gesteld op 26-1-2024 om 11:10

    Reageer op deze vraag Misbruik melden
  • Hoeveel slagen moeten de diep verzonken afstelschroeven met speciale afstel schroevendraaier van een Hitachi CS 33 EB opengedraaid worden.
    m.v.g. Sam
    Gesteld op 26-1-2024 om 10:58

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CS33EB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CS33EB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 10,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info