565951
6
Verklein
Vergroot
Pagina terug
1/41
Pagina verder
5
English
HOW TO USE
CAUTIONS
Do not remove the insulation cover. It is necessary
to support the body of the tool.
During operation, the base of the tool should be
pressed against the material, as shown in Fig. 6,
herein. If the tool is not properly pressed against
the maerial, the blade may be damaged by vibration.
1. Cutting metallic materials
Ensure the material is firmly held in position during
operation. Always use an appropriate cutting agent
(spindle oil, soapy water, etc.). When a liquid cutting
agent is not available, apply grease to the material
to be cut.
2. Cutting lumber
When cutting lumber, ensure that the wooden
material is firmly fixed in position.
3. Sawing curved lines
Use a No. 6 or No. 7 blade (optional accessories)
as described below.
For metal-working - No. 6
For wood-working - No. 7
When sawing a small circular arc, reduce the feeding
speed of the machine.
4. Cut off guide for cutting pipe (optional accessory)
NOTE
Please refer to the cut off guide users manual for
details on how to use ti correctly.
SELECTION OF BLADES
To ensure maximum operating efficiency and results, it
is very important to select the appropriate blade best
suited to the type and thickness of the material to be cut.
Three types of blades are provided as standard
accessories.
The blade number is engraved in the vicinity of the
mounting position of each blade. Select appropriate
blades by refering to Tables 1 and 2 below.
Table 1
Product
Cutting Blade Applicable
Code No.
application
used products
Cut-off Outer diameter
Model CR10V 984449
guide (L)
75mm 175mm
No. 9
Model CR12,
CR12V
996420
Cut-off Outer diameter
Model CR10V 984448
guide (S) 10mm 55mm
No. 1
Model CR12,
996429
CR12V
NOTE
No. 2, No. 4, No. 6, No. 7, No. 8, No. 9, No. 95,
and No. 96 blades are sold separately.
For other materials.
Table 2
MAINTENANCE AND INSPECTION
1. Inspecting the blade
Continued use of a dull or damaged blade will
result in reduced cutting efficiency and may cause
overloading of the motor. Replace the blade with
a new one as soon as excessive abrasion is noted.
2. Inspecting the mounting screws:
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
Blade
Uses
Thickness
No. (mm)
No.1
For cutting steel pipe less
than 115mm in diameter
2.5 6
No.2
For cutting steel pipe less
than 40mm in diameter
2.5 6
No.3
For cutting steel pipe less
than 40mm in diameter
Below 3.5
Blade
Uses
Thickness
No. (mm)
No.4
For cutting and roughing
lumber
50 100
No.5
For cutting and roughing
lumber
Below 50
No.6
For sawing curved lines
iron plate
Below 3.5
No.7
For sawing curved lines
lumber
Below 30
No.8
For cutting vinyl chloride
pipe less than 115mm in
diameter
2.5 15
For cutting and roughing
lumber
Below 50
No.9
For cutting mild steel pipe
less than 175mm in diameter
when used with cut off guide
2.5 6
No.95
For cutting stainless steel
pipe less than 115mm in
diameter
Below 2.5
No.96
For cutting stainless steel
pipe less than 40mm in
diameter
Below 2.5
Material
Material quality
Thickness Blade
to be cut (mm) No.
Iron plate Mild steel plate
Below 3.5 No.3,6
2.5 12 No.1,2
Nonferrous Aluminium, Below 5 No.3,6
metal Copper, Brass 5 20 No.1,2
Synthetic
Phenol resin,
restin
Melamine
5 30 No.3,5,8
resin, etc.
10 50 No.1,2,4,
Vinyl chloride 5 30 No.3,5,8
Acrylic resin, etc. 10 60 No.1,2,4
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CR12 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CR12 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 0,64 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info