Handleiding Hitachi CP-EX250 (pagina 60 van 79) (Engels)

538046

Verklein

Vergroot

Pagina terug

1/79

Pagina verder

Projector

User's Manual (detailed)

Operating Guide

Thank you for purchasing this projector.

►Before using this product, please read all manuals for this

product. Be sure to read Safety Guide rst. After reading them, store them in a

safe place for future reference.

WARNING

• The information in this manual is subject to change without notice.

• The illustrations in this manual are for illustrative purposes. They may differ

slightly from your projector.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

NOTE

Trademark acknowledgment

Various symbols are used in this manual. The meanings of these symbols are

described below.

About this manual

WARNING

CAUTION

This symbol indicates information that, if ignored, could possibly

result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly

result in personal injury or physical damage due to incorrect

handling.

Please refer to the pages written following this symbol.



• Mac

is a registered trademark of Apple Inc.

• Windows

, DirectDraw

and Direct3D

are registered trademarks of Microsoft Corporation

in the U.S. and/or other countries.

• VESA and DDC are trademarks of the Video Electronics Standard Association.

•

HDMI, the HDMI logo, and High-Denition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC in the United States and other countries.

• Blu-ray Disc

and Blu-ray

are trademarks of Blu-ray Disc

Association.

All other trademarks are the properties of their respective owners.

NOTICE This entry notices of fear of causing trouble.

CP-EX250/CP-EX300

Contents

Introduction . . . . . . . . . . . . . . . 3

Features . . . . . . . . . . . . . . . . . . . . . . 3

Checking the contents of package

...3

Part names . . . . . . . . . . . . . . . . . . . . 4

Setting up . . . . . . . . . . . . . . . . . 7

Arrangement ...................7

Connecting with your devices

.....10

Connecting to a power supply

.....14

Using the security bar and slot . . . . 15

Remote control ............16

Installing the batteries ...........16

About the remote control signal . . . 17

Changing the frequency of remote

control signal ..................17

Power on/off . . . . . . . . . . . . . . 18

Turning on the power . . . . . . . . . . . 18

Turning off the power . . . . . . . . . . . 19

Operating . . . . . . . . . . . . . . . . 20

Adjusting the volume ............20

Temporarily muting the sound .....20

Selecting an input signal .........21

Searching an input signal . . . . . . . . 22

Selecting an aspect ratio .........23

Adjusting the projector's elevator . . 24

Adjusting the zoom and focus .....24

Using the automatic adjustment feature

...25

Adjusting the position . . . . . . . . . . . 25

Correcting the keystone distortions

. . 26

Using the magnify feature ........27

Temporarily freezing the screen . . . 28

Temporarily blanking the screen . . 28

Using the menu function . . . . . . . . 29

EASY MENU. . . . . . . . . . . . . . . 31

As p e c t ,

e y s t o n e

pi c t u r e m o d e ,

ec o m o d e , in s t A l l A t i o n , re s e t , Fi l t e r t i m e ,

A n g u A g e , Ad v A n c e d m e n u , ex i t

PICTURE menu . . . . . . . . . . . . 33

Br i g h t n e s s , co n t r A s t , gA m m A , co l o r t e m p ,

co l o r , ti n t , sh A r p n e s s , my m e m o r y

IMAGE menu . . . . . . . . . . . . . . 36

As p e c t , ov e r s c A n , v p o s i t i o n , h p o s i t i o n ,

p h A s e , h s i z e , Au t o A d j u s t e x e c u t e

INPUT menu . . . . . . . . . . . . . . 39

pr o g r e s s i v e , vi d e o n r , co l o r s p A c e ,

i d e o F o r m A t , hd m i F o r m A t , hd m i r A n g e ,

o m p u t e r i n, Fr A m e l o c K , re s o l u t i o n



SETUP menu ..............43

e y s t o n e , Au t o e c o m o d e , ec o m o d e ,

in s t A l l A t i o n , st A n d B y m o d e , mo n i t o r o u t

AUDIO menu . . . . . . . . . . . . . . 46

vo l u m e , sp e A K e r , Au d i o s o u r c e

SCREEN menu .............47

lA n g u A g e , me n u p o s i t i o n , Bl A n K ,

u t o B l A n K , st A r t u p ,

yScreen

yScreen Lock

, me s s A g e , so u r c e n A m e ,

e m p l A t e , c.c.

OPTION menu . . . . . . . . . . . . . 53

Au t o s e A r c h , di r e c t p o w e r o n ,

u t o p o w e r o F F , lA m p t i m e , Fi l t e r t i m e ,

y B u t t o n , my s o u r c e , se r v i c e

SECURITY menu ...........60

se c u r i t y p A s s w o r d c h A n g e ,

yScreen

p A s s w o r d , pi n l o c K ,

y t e x t p A s s w o r d , my t e x t d i s p l A y ,

y t e x t w r i t i n g

Maintenance ..............65

Replacing the lamp .............65

Cleaning and replacing the air lter . . 67

Other care ....................69

Troubleshooting . . . . . . . . . . . 70

Related messages . . . . . . . . . . . . . 70

Regarding the indicator lamps . . . . 72

Resetting all settings ............75

Phenomena that may be easy

to be mistaken for machine defects

. . . 75

Specications .............79



Introduction

• Keep the original packing materials, for future reshipment. Be sure

to use the original packing materials when moving the projector. Use special

caution for the lens.

• The projector may make a rattling sound when tilted, moved or shaken, since

a ap to control the air ow inside of the projector has moved. Be aware that

this is not a failure or malfunction.

NOTE

The projector provides you with the broad use by the following features.

Checking the contents of package

ü This projector has a variety of I/O ports that supposedly cover for any scene.

ü This lightweight projector requires only a minimal amount of space for

installation.

ü This projector has a capability to project various picture signals onto a screen.

Please see the Contents of package section in the User’s Manual (concise)

which is a book. Your projector should come with the items shown there. Require

of your dealer immediately if any items are missing.

Features

►Keep small parts away from children and pets. Take care

not to put in the mouth. If swallowed, consult a physician immediately for

emergency treatment.

WARNING

Introduction

►Do not open or remove any portion of the product, unless the

manuals direct it.

►Do not subject the projector to unstable conditions.

►Do not apply a shock or pressure to this product.

►Do not look into the lens and the openings on the projector while the lamp is

on.

WARNING

►Do not touch around the lamp cover and the exhaust

vents during use or just after use, since it is too hot.

►Do not attach anything onto the lens because it could damage the lens,

such as melting the lens.

CAUTION

(continued on next page)

Part names

(1) Lamp cover (65)

The lamp unit is inside.

(2) Speaker (

20, 46)

(3) Filter cover (67)

The air lter and intake vent are inside.

(4) Elevator feet (x2) (24)

(5) Elevator button (24)

(6) Remote sensor (17)

(7) Lens (69)

(8) Intake vents

(9) Control panel (5)

(10) FOCUS ring (24)

(11) ZOOM ring (24)

(12) AC (AC inlet) (14)

(13) Exhaust vent

(14) Rear panel (5)

(7)

(4)(5)

(6)

(8)

(3)

(2)

(12)

(13)

(14) (9)

(9)

(1)

(11)

(10)

(4)

Introduction

Part names (continued)

Control panel

(1) STANDBY/ON button (

18)

(2) INPUT button (21)

(3) MENU button (29)

(4) LAMP indicator (72)

(5) TEMP indicator (72)

(6) POWER indicator (72)

Rear panel (

10 ~ 13)

(1) HDMI port

(2) AUDIO IN (R,L) ports

(3) AUDIO OUT (R,L) ports

(4) COMPUTER IN1 port

(5) COMPUTER IN2 / MONITOR OUT port

(6) CONTROL port

(7) VIDEO port

(8) Security slot (

15)

(9) Security bar (15)

(continued on next page)

(1) (3)(2) (6)

(4)(5)

(5)

(4)

(1)

(2)(9) (8)(3)

(7)

(6)

Introduction

Part names (continued)

Remote control

(1) VIDEO button (

21)

(2) COMPUTER button (21)

(3) SEARCH button (22)

(4) STANDBY/ON button (18)

(5) ASPECT button (23)

(6) AUTO button (25)

(7) BLANK button (28)

(8) MAGNIFY - ON button (27)

(9) MAGNIFY - OFF button (27)

(10) MY SOURCE/DOC.CAMERA button

(22, 57)

(11) VOLUME - button (20)

(12) PAGE UP button *

(13) PAGE DOWN button *

(14) VOLUME + button (20)

(15) MUTE button (20)

(16) FREEZE button (28)

(17) MY BUTTON - 1 button (56, 57)

(18) MY BUTTON - 2 button (56, 57)

(19) KEYSTONE button (26)

(20) POSITION button (25, 29)

(21) MENU button (29)

(22) ▲/▼/◄/► cursor buttons (29)

(23) ENTER button (29)

(24) ESC button (29)

(25) RESET button (29)

(26) Battery cover (16)

Back of

the remote control

(2)

(1)

(6)

(5)

(16)

(8)

(9)

(19)

(17)

(20)

(22)

(24)

(10)

(4)

(3)

(7)

(12)

(14)

(11)

(13)

(15)

(18)

(21)

(23)

(25)

(26)

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





ENTER

• Any button marked with “*” is not supported on this projector (71).

NOTE

Setting up

Install the projector according to the environment and manner the projector will be

used in.

For the case of installation in a special state such as ceiling mount, the specied

mounting accessories (

Specications in the User’s Manual (concise)) and

service may be required. Before installing the projector, consult your dealer about

your installation.

Arrangement

Refer to table T-1 and gures F-1 and F-2 at the end of User’s Manual (concise)

to determine the screen size and projection distance.

The values shown in the table are calculated for a full size screen.

(continued on next page)

• If the projector is used at an altitude of about 1600 m (5250 feet) or higher,

set ALTITUDE of the SERVICE item in the OPTION menu to HIGH (

57).

Otherwise, set it to NORMAL. If the projector is used with a wrong setting, it may

cause damage to the projector itself or the parts inside.

a Screen size (diagonal)

b Projection distance (±10%, from the projector’s end)

c1 , c2 Screen height (±10%)

• The screen position may shift after installation if the projector is

suspended from the ceiling or other location due to the exibility of the plastic

projector body. If readjustment is necessary, consult with your dealer or service

personnel.

NOTE

Setting up

Arrangement (continued)

WARNING

(continued on next page)

►Install the projector where you can access the power

outlet easily. If an abnormality should occur, unplug the projector urgently.

Otherwise it could cause a re or electric shock.

►Do not subject the projector to unstable conditions. If the projector falls

or topples over, it could result in injury or damage to the projector and the

surrounding things. Using a damaged projector could result in a re and an

electric shock.

• Do not place the projector in unstable places, such as an inclined surface,

places subject to vibration, on top of a wobbly table or cart, or a surface that is

smaller than the projector.

• Do not put the projector on its side, front or rear position.

• Do not attach nor place anything on the projector unless otherwise specied in

the manual.

• Do not use any mounting accessories except the accessories specied by the

manufacturer. Read and keep the manuals of the accessories used.

• For special installation such as ceiling mounting, be sure to consult your dealer

beforehand.

►

Do not install the projector near thermally conductive or ammable

things. Such things when heated by the projector could result in a re and burns.

• Do not place the projector on a metal stand.

►Do not place the projector where any oils, such as cooking or machine

oil, are used. Oil may harm the product, resulting in malfunction, or falling from

the mounted position.

►Do not place the projector in a place where it may get wet. Getting the

projector wet or inserting liquid into the projector could cause a re and an

electric shock, and damage the projector.

• Do not place the projector near water, such as in a bathroom, kitchen, or

poolside.

• Do not place the projector outdoors or by the window.

• Do not place anything containing liquid near the projector.

Setting up

Arrangement (continued)

►Place the projector in a cool place with sufcient

ventilation. The projector may shutdown automatically or may malfunction if its

internal temperature is too high.

Using a damaged projector could result in a re and an electric shock.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

• Do not place the projector where the air from an air conditioner or similar unit

will blow on it directly.

• Keep a space of 30 cm or more between a side of the projector and other

objects such as walls.

• Do not place the projector on carpet, cushions or bedding.

• Do not stop up, block nor cover the projector's vent holes. Do not place

anything around the projector that could be sucked in or stuck to the projector's

intake vents.

• Do not place the projector at places that are exposed to magnetic elds, doing

so can cause the cooling fans inside the projector to malfunction.

►Avoid placing the projector in smoky, humid or dusty place. Placing the

projector in such places could cause a re, an electric shock and malfunction of

the projector.

• Do not place the projector near humidiers. Especially for an ultrasonic

humidier, chlorine and minerals contained in tap water are atomized and could

be deposited in the projector causing image degradation or other problems.

• Do not place the projector in a smoking area, kitchen, passageway

or by the window.

• Position the projector to prevent light from directly hitting the projector's remote

sensor.

• Do not place the product in a place where radio interference may be caused.

• Check and correct the setting for ALTITUDE of SERVICE in the OPTION menu

according to the usage environment (

57). If the projector is used with a wrong

setting, it may cause damage to the projector itself or the parts inside.

• Keep heat-sensitive things away from the projector. Otherwise, they may be

damaged by the heat from the projector.

CAUTION

NOTICE

Setting up

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to

conrm that the device is suitable for connecting with this projector and prepare

the required accessories, such as a cable in accord with the signal of the device.

Consult your dealer when the required accessory did not come with the product or

the accessory is damaged.

After making sure that the projector and the devices are turned off, perform

the connection, according to the following instructions. Refer to the gures in

subsequent pages.

►Use only the appropriate accessories. Otherwise it could

cause a re or damage the projector and devices.

• Use only the accessories specied or recommended by the projector’s

manufacturer. It may be regulated under some standard.

• Neither disassemble nor modify the projector and the accessories.

• Do not use the damaged accessory. Be careful not to damage the accessories.

Route a cable so that it is neither stepped on nor pinched out.

WARNING

►For a cable with a core at only one end, connect the end

with the core to the projector. That may be required by EMI regulations.

CAUTION

• Do not turn on or off the projector while connected to a device in

operation, unless that is directed in the manual of the device. Otherwise it may

cause malfunction in the device or projector.

• The function of some input ports can be selected according to your usage

requirements. Check the reference page indicated beside each port in the

following illustration.

• Be careful not to mistakenly connect a connector to a wrong port. Otherwise it

may cause malfunction in the device or projector.

- When connecting a connector to a port, make sure that the shape of the

connector ts the port.

- Tighten the screws to connect a connector equipped with screws to a port.

- Use the cables with straight plugs, not L-shaped ones, as the input ports of

the projector are recessed.

NOTE

(continued on next page)

Setting up

• Plug-and-Play is a system composed of a computer, its operating system

and peripheral equipment (i.e. display devices). This projector is VESA DDC

2B compatible. Plug-and-Play can be used by connecting this projector to a

computer that is VESA DDC (display data channel) compatible.

- Take advantage of this feature by connecting a computer cable to the

COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work

properly if any other type of connection is attempted.

- Please use the standard drivers in your computer as this projector is a Plug-

and-Play monitor.

About Plug-and-Play capability

(continued on next page)

Connecting with your devices (continued)

• Before connecting the projector to a computer, consult the computer’s

manual and check the compatibility of the signal level, the synchronization

methods and the display resolution output to the projector.

- Some signal may need an adapter to input this projector.

- Some computers have multiple screen display modes that may include some

signals which are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA

(1600x1200), the signal will be converted to the projector’s panel resolution

before being displayed. The best display performance will be achieved if the

resolutions of the input signal and the projector panel are identical.

• If you connect this projector and a notebook computer, you need output the

display to an external monitor, or output simultaneously to the internal display

and an external monitor. Consult the computer's manual for the setting.

• Depending on the input signal, the automatic adjustment function of this

projector may take some time and not function correctly.

- Note that a composite sync signal or sync-on-green signal may confuse the

automatic adjustment function of this projector (25).

- If the automatic adjustment function does not work correctly, you may not see

the dialog to set the display resolution. In such a case, use an external display

device. You may be able to see the dialog and set an appropriate display

resolution.

NOTE

(continued on next page)

Setting up

ComputerExternal device

Setting up

• The HDMI port of this model is compatible with HDCP (High-band-

width Digital Content Protection) and therefore capable of displaying a video

signal from HDCP compatible DVD players or the like.

- The HDMI supports the following signals.

Video signal : 480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60,

1080i@50/60, 1080p@50/60

Audio signal : Format Linear PCM

Sampling frequency 48kHz / 44.1kHz / 32kHz

- This projector can be connected with another equipment that has HDMI

connector, but with some equipment the projector may not work properly,

something like no video.

- Be sure to use an HDMI

cable that has the HDMI

logo.

- Use a Category 2-certi ed HDMI

cable to input 1080p@50/60 signal to the

projector.

- When the projector is connected with a device having DVI connector, use a

DVI to HDMI

cable to connect with the HDMI input.

NOTE

Connecting with your devices (continued)

(continued on next page)

VCR/DVD/Blu-ray Disc

player

Speakers

(with an ampli er)

Monitor

RGB IN

Connecting to a power supply

Put the connector of the power cord into the

AC (AC inlet) of the projector.

Firmly plug the power cord’s plug into the

outlet. In a couple of seconds after the

power supply connection, the POWER

indicator will light up in steady orange.

►Please use extra caution when connecting the power cord, as

incorrect or faulty connections may result in re and/or electrical shock.

• Do not touch the power cord with a wet hand.

• Only use the power cord that came with the projector. If it is damaged, consult

your dealer to get a new one. Never modify the power cord.

• Only plug the power cord into an outlet whose voltage is matched to the power

cord. The power outlet should be close to the projector and easily accessible.

Remove the power cord for complete separation.

• Do not distribute the power supply to multiple devices. Doing so may overload

the outlet and connectors, loosen the connection, or result in re, electric shock

or other accidents.

• Connect the ground terminal for the AC inlet of this unit to the ground terminal

of the building using an appropriate power cord (bundled).

WARNING

Please remember that when the DIRECT POWER

ON function activated (53), the connection of the

power supply make the projector turn on.

Setting up

►This product is also designed for IT power systems with a phase-to-

phase voltage of 220 to 240 V.

NOTICE

Power

cord

Using the security bar and slot

A commercially available anti-theft chain or

wire can be attached to the security bar on

the projector. Refer to the  gure to choose

an anti-theft chain or wire.

Also this product has the security slot for

the Kensington lock.

For details, see the manual of the security

tool.

►Do not use the security bar and slot to prevent the projector

from falling down, since it is not designed for it.

WARNING

►Do not place anti-theft chain or wire near the exhaust vents.

It may become too hot.

CAUTION

• The security bar and slot is not comprehensive theft prevention

measures. It is intended to be used as supplemental theft prevention measure.

NOTE

Setting up

Security slot

18.6mm

18.0mm

12.2mm

security bar

Anti-theft

chain or wire

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control

starts to malfunction, try to replace the batteries. If you will not use the remote control for

long period, remove the batteries from the remote control and store them in a safe place.

Holding the hook part of the battery

cover, remove it.

Align and insert the two AA batteries

(HITACHI MAXELL ENERGY Part No.LR6

or R6P)

according to their plus and minus

terminals as indicated in the remote control.

Replace the battery cover in the direction of the arrow and snap it back into place.

►Always handle the batteries with care and use them only as

directed. Improper use may result in battery explosion, cracking or leakage,

which could result in re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specied. Do not use batteries of different

types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.

•

If you observe battery leakage, wipe out the leakage and then replace a battery.

If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

WARNING

Remote control

21 3

About the remote control signal

The remote control works with the projector’s remote

sensor. This projector has a remote sensor on the front.

The sensor senses the signal within the following range

when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor)

within 3 meters about.

•

The remote control signal re ected in the screen or the like may be available.

If it is dif cult to send the signal to the sensor directly, attempt to make the signal re ect.

• The remote control uses infrared light to send signals to the projector (Class 1

LED), so be sure to use the remote control in an area free from obstacles that

could block the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun

light) or light from an extremely close range (such as from an inverter  uorescent

lamp) shines on the remote sensor of the projector. Adjust the position of

projector avoiding those lights.

NOTE

Remote control

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal

frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control

does not function properly, attempt to change the signal frequency.

In order to set the Mode, please keep pressing the combination of

two buttons listed below simultaneously for about 3 seconds.

(1)

(2)

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





ENTER

(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons

(2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons

Please remember that the REMOTE FREQ. in the SERVICE item of

the OPTION menu

(



59)

of the projector to be controlled should be

set to the same mode as the remote control.

(approx.)

Make sure that the power cord is rmly and

correctly connected to the projector and the

outlet.

Turning on the power

Make sure that the POWER indicator is

steady orange (72).

Press STANDBY/ON button on the

projector or the remote control.

The projection lamp will light up and POWER

indicator will begin blinking in green. When the

power is completely on, the indicator will stop blinking and light in steady

green (72).

Power on/off

To display the picture, select an input signal according to the section Selecting an

input signal (21).

Power on/off

The INITIAL SETTING Menu will be displayed by factory default upon startup.

Once the INITIAL SETTING Menu is set, it will not appear until FACTORY RESET

(59) is executed. If you wish to change the settings, refer to the LANGUAGE

(47) and ALTITUDE (57) menu.

(1) LANGUAGE: Use the ▲/▼/◄/►

buttons to select the desired language

and press the ENTER button of the

remote control or the INPUT button of

the projector to execute.

(2) ALTITUDE: Use the ▲/▼ buttons to

select NORMAL for altitude below

1600 m (5250 feet), otherwise select

HIGH and press the ENTER button of

the remote control or the INPUT button

of the projector to execute.

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

STANDBY/ON button

POWER indicator

Power on/off

►A strong light is emitted when the projector’s power is on.

Do not look into the lens of the projector or look inside of the projector through

any of the projector’s openings.

►Do not touch around the lamp cover and the exhaust vents during use or just

after use, since it is too hot.

WARNING

Press the STANDBY/ON button on the projector or the remote control.

The message “Power off?” will appear on the screen for about 5 seconds.

Turning off the power

Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in

orange. Then POWER indicator will stop blinking and light in steady orange

when the lamp cooling is complete (72).

Do not turn the projector on for about 10 minutes or more after turning it off.

Also, do not turn the projector off shortly after turning it on. Such operations might

cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

• Turn the power on/off in right order. Please power on the projector

prior to the connected devices.

• This projector has the function that can make the projector automatically turn

on/off. Please refer to the DIRECT POWER ON (53) and AUTO POWER

OFF (54) items of the OPTION menu.

NOTE

Operating

Adjusting the volume

Use the VOLUME +/VOLUME - buttons to adjust the volume.

A dialog will appear on the screen to aid you in adjusting the

volume. If you do not do anything, the dialog will automatically

disappear after ten seconds.

● When

is selected for current picture input port, the volume

adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu

(46).

● Even if the projector is in the standby mode, the volume is adjustable when

both of the following conditions are true:

- An option other than is selected for STANDBY in the AUDIO SOURCE

item of the AUDIO menu (46).

NORMAL is selected in the STANDBY MODE item of the SETUP menu

(45).

Press MUTE button on the remote control.

A dialog will appear on the screen indicating that you have muted

the sound.

To restore the sound, press the MUTE, VOLUME + or

VOLUME - button. Even if you do not do anything, the dialog

will automatically disappear after ten seconds.

Temporarily muting the sound

● When is selected for current picture input port, the sound is always muted.

Please see AUDIO SOURCE item of AUDIO menu (46).

● C.C. (Closed Caption) is automatically activated when sound is muted and

an input signal containing C.C. is received. This function is available only

when the signal is NTSC for VIDEO, or 480i@60 for COMPUTER IN1 or

COMPUTER IN2, and when AUTO is selected for DISPLAY in the C.C. menu

under the SCREEN menu (52).

VOLUME +/- button

MUTE button

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

Operating

Press INPUT button on the projector.

Each time you press the button, the projector switches its

input port from the current port as below.

Selecting an input signal

● While ON is selected for AUTO SEARCH item in OPTION menu (53), the

projector will keep checking the ports in above order repeatedly till an input

signal is detected.

Press VIDEO button on the remote control.

Each time you press the button, the projector switches its

input port from the current port as below.

● While ON is selected for AUTO SEARCH item in OPTION menu,

the projector will keep checking every port sequentially till an input signal

is detected (

53). If VIDEO button is pressed when COMPUTER IN1 or

COMPUTER IN2 port is selected, the projector will check HDMI port  rst.

VIDEO button

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

Press COMPUTER button on the remote control.

Each time you press the button, the projector switches its

input port from the current port as below.

●

While ON is selected for AUTO SEARCH item in OPTION menu, the

projector will keep checking every port sequentially till an input signal is

detected (53). If COMPUTER button is pressed when VIDEO or HDMI port

is selected, the projector will check COMPUTER IN1 port  rst.

COMPUTER button

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

COMPUTER IN1  COMPUTER IN2

VIDEO



HDMI

HDMI  VIDEO

COMPUTER IN1  COMPUTER IN2

Operating

INPUT

button

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

MY SOURCE /

DOC. CAMERA button

Press the MY SOURCE / DOC. CAMERA button on

the remote control. The input signal will be changed

into the signal you set as MY SOURCE (57).

● This function also can use for document camera. Select the

input port that connected the document camera.

Operating

Press SEARCH button on the remote control.

The projector will start to check its input ports as below in

order to  nd any input signals.

When input signal is detected, the projector will stop

searching and display the image. If no signal is found,

the projector will return to the state selected before the

operation.

Searching an input signal

● While ON is selected for AUTO SEARCH item in OPTION menu (53), the

projector will keep checking the ports in above order repeatedly till an input

signal is detected.

SEARCH button

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

Selecting an input signal(continued)

COMPUTER IN1  COMPUTER IN2

VIDEO



HDMI

Operating

Selecting an aspect ratio

● ASPECT button does not work when no proper signal is inputted.

● NORMAL mode keeps the original aspect ratio setting.

● The display will be dark for a split second while switching the Aspect, but this

is not a malfunction.

 For a computer signal

NORMAL  4:3  16:9  16:10

 For a video signal or component video signal

4:3  16:9  14:9

 For no signal

4:3 ( xed)

Press ASPECT button on the remote control.

Each time you press the button, the projector switches the

mode for aspect ratio in turn.

ASPECT button

 For an HDMI

signal

NORMAL  4:3  16:9  16:10  14:9

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

Operating

Use the ZOOM ring to adjust the screen size.

Use the FOCUS ring to focus the picture.

Adjusting the zoom and focus

►

Do not handle the

elevator button without holding the projector,

since the projector may drop down.

►Do not tilt the projector other than

elevating its front within 12 degrees using

the elevator foot. A tilt of the projector

exceeding the restriction could cause

malfunction or shortening the lifetime of

consumables, or the projector itself.

CAUTION

Using the Front elevator foot can tilt the projector in order to project at a suitable

angle to the screen, elevating the front side of the projector within 12 degrees.

The elevator foot is adjustable while pushing the elevator button.

Holding the projector, push the elevator

button to loose the elevator foot.

Release the elevator button in order to

lock the elevator foot.

If necessary, the elevator foot can be manually

twisted to make more precise adjustments.

Hold the projector when twisting the foot.

When the place to put the projector is slightly uneven to the left or right, use the

Rear elevator foot to place the projector horizontally.

A spacer is installed on the

Rear elevator foot at the time of shipment, and the projector is ready for use. If

necessary, detach the spacer, and the elevator foot can be manually twisted to

make more precise adjustments.

Adjusting the projector’s elevator

12°

Front foot

Rear foot

Elevator button

►Keep the spacer away from children and pets. Be careful not

to let them swallow the spacer. If swallowed consult a physician immediately for

emergency treatment.

WARNING

•

After the foot is adjusted, it is possible to return it to the state of the shipment

with a spacer.

It is recommended to keep the spacer and reuse it when relocating

the projector.

NOTE

FOCUS ring

ZOOM ring

Operating

Press POSITION button on the remote control when no menu is

indicated.

The “POSITION” indication will appear on the screen.

Adjusting the position

Use the ▲/▼/◄/► cursor buttons to adjust the picture position.

When you want to reset the operation, press RESET button on

the remote control during the operation.

To complete this operation, press POSITION button again. Even if

you do not do anything, the dialog will automatically disappear

after a few seconds.

●

When this function is performed on a video signal, some image such as an extra-

line may appear at outside of the picture.

● When this function is performed on a video signal, the range of this adjustment

depends on OVER SCAN in IMAGE menu (

37) setting. It is not possible to

adjust when OVER SCAN is set to 10.

● If POSITION button is pressed when a menu is indicated on screen, the displayed

picture does not move its position but the menu does.

● This function is unavailable for signal from the HDMI port.

Press AUTO button on the remote control.

Pressing this button performs the following.

Using the automatic adjustment feature

 For a computer signal

The vertical position, the horizontal position and the horizontal

phase will be automatically adjusted.

Make sure that the application window is set to its maximum size

prior to attempting to use this feature. A dark picture may still be

incorrectly adjusted. Use a bright picture when adjusting.

 For a video signal

The video format best suited for the respective input signal will be selected

automatically. This function is available only when the AUTO is selected for

the VIDEO FORMAT item in the INPUT menu (

40).

The vertical position and

horizontal position will be automatically set to the default.

● The automatic adjustment operation requires approx. 10 seconds. Also please

note that it may not function correctly with some input.

● When this function is performed for a video signal, a certain extra such as a line

may appear outside a picture.

● When this function is performed for a computer signal, a black frame may be

displayed on the edge of the screen, depending on the computer model.

●

The items adjusted by this function may vary when the FINE or DISABLE is selected

for the AUTO ADJUST item of the SERVICE item in the OPTION menu (

58).

POSITION button

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

AUTO button

 For a component video signal

The vertical position and horizontal position will be automatically set to the default.

The horizontal phase will be automatically adjusted.

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

Operating

Press KEYSTONE button on the remote

control. A dialog will appear on the screen

to aid you in correcting the distortion.

Correcting the keystone distortions

Use the ◄/► buttons for adjustment.

To close the dialog and complete this operation, press

KEYSTONE button again. Even if you do not do anything, the

dialog will automatically disappear after ten seconds.

● The menu or dialog will automatically disappear after several seconds of

inactivity. Pressing the KEYSTONE button again  nishes the operation and

closes the menu or dialog.

● The adjustable range of this function will vary among inputs. For some input,

this function may not work well.

● When REAR / CEILING or FRONT / CEILING is selected for the

INSTALLATION item in the SETUP menu, the automatic vertical keystone

correction function may not work correctly if the projector screen is slanted or

tilted downwards.

● When the zoom adjustment is set to the TELE (telephoto focus), this function

may be excessive. This function should be used when the zoom adjustment

is set to the full WIDE (wide-angle focus) whenever possible.

● When the projector is inclined to near ±30 degree or over, this function may

not work well.

● The display will be dark for a split second while switching the KEYSTONE,

but this is not a malfunction.

KEYSTONE button

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

Operating

Using the magnify feature

MAGNIFY

ON/OFF button

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

Press the MAGNIFY ON button on the remote control.

The picture will be magni ed, and the MAGNIFY dialog

will appear on the screen. When the MAGNIFY

ON button is pressed for the  rst time after the

projector is turned on, the picture will be zoomed

by 1.5 times. On the dialog, triangle marks to show

each direction will be displayed.

The display magni cation of the projector switches in order with every press

of the MAGNIFY ON button.

 For computer signals or HDMI

(RGB) signals

1.5 times  2 times  3 times  4 times  1 time

 For video signals, component video signals or HDMI

(Component)

signals

1.5 times  2 times  1 time

While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor

buttons to shift the magnifying area.

Press the MAGNIFY OFF button on the remote control to exit magni cation.

● The MAGNIFY dialog will automatically disappear in several seconds with no

operation. The dialog will appear again if the MAGNIFY ON button is pressed

when the dialog has automatically disappeared.

● The magni cation is automatically disabled when the displaying signal or its

display condition is changed.

● While the magni cation is active, the keystone distortion condition may vary.

It will be restored when the magni cation is disabled.

● Some horizontal stripes might be visible on the image while magni cation is

active.

● This function is not available in the following cases:

- A sync signal in the range not supported is input.

- There is no input signal.

Press BLANK button on the remote control.

The BLANK screen will be displayed instead of the screen of

input signal. Please refer to BLANK item in SCREEN menu

(47).

To exit from the BLANK screen and return to the input signal

screen, press BLANK button again.

Temporarily blanking the screen

● The projector automatically exits from the

BLANK

mode when

some control buttons are pressed.

•

The sound is not connected with the BLANK screen function. If

necessary, set the volume or mute rst. To display the BLANK screen and mute

the sound at one time, use AV MUTE function

(57).

NOTE

Press the FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen (however,

the indication will not appear when the OFF is selected for

the MESSAGE item in the SCREEN menu (49)), and the

projector will go into the FREEZE mode, which the picture is

frozen.

To exit the FREEZE mode and restore the screen to normal,

press the FREEZE button again.

Temporarily freezing the screen

● The projector automatically exits from the FREEZE mode when some control

buttons are pressed.

● If the projector continues projecting a still image for a long time, the LCD

panel might possibly be burned in. Do not leave the projector in the FREEZE

mode for too long.

● Images might appear degraded when this function is operated, but it is not a

malfunction.

FREEZE button

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





ENTER

BLANK button

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

࡯

㧗

VOLUME





ENTER

►If you wish to have a blank screen while the projector's lamp

is on, use the BLANK function above.

Taking any other action may cause the damage on the projector.

CAUTION

Operating

To start the MENU, press the MENU button. The MENU you last used (EASY

or ADVANCED) will appear. EASY MENU has priority to appear just after

powered on.

Using the menu function

(1) Use the ▲/▼ cursor buttons to select an item to

operate. If you want to change it to the ADVANCED

MENU, select the ADVANCED MENU.

(2) Use the ◄/► cursor buttons to operate the item.

This projector has the following menus:

PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, SECURITY and

EASY MENU.

EASY MENU consists of functions often used, and the other menus are classied

into each purpose and brought together as the ADVANCED MENU.

Each of these menus is operated using the same methods. While the projector

is displaying any menu, the MENU button on the projector works as the cursor

buttons. The basic operations of these menus are as follows.

In the EASY MENU

(continued on next page)

(1) Use the ▲/▼ cursor buttons to select a menu.

If you want to change it to the EASY MENU,

select the EASY MENU.

The items in the menu appear on the right side.

(2) Press the ► cursor button or ENTER button to

move the cursor to the right side. Then use the

▲/▼ cursor buttons to select an item to operate and press the ► cursor

button or ENTER button to progress. The operation menu or dialog of the

selected item will appear.

(3) Use the buttons as instructed in the OSD to operate the item.

In the ADVANCED MENU

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT

BLANK

MUTE

MY BUTTON

POSITION

ESC

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

PAGE

DOWN

OFF

FREEZE

ー

＋

VOLUME

ENTER

POSITION

ESC

RESET

ENTER

POSITION button

ENTER button

ESC button

MENU button

(Cursor buttons)

Cursor buttons

RESET button

Using the menu function (continued)

To close the MENU, press the MENU button again or select EXIT and press

the ◄ cursor button or ENTER button. Even if you do not do anything, the

dialog will automatically disappear after about 30 seconds.

●

If you want to move the menu position, use the cursor buttons after pressing

the POSITION button.

● Some functions cannot be performed when a certain input port is selected,

or when a certain input signal is displayed.

● When you want to reset the operation, press RESET button on the remote

control during the operation. Note that some items (ex. LANGUAGE,

VOLUME) cannot be reset.

● In the ADVANCED MENU, when you want to return to the previous display,

press the ◄ cursor button or ESC button on the remote control.

Indication in OSD (On Screen Display)

The meanings of the general words on the OSD are as follows.

Indication Meaning

EXIT

Selecting this word nishes the OSD menu. It's the same as

pressing the MENU button.

RETURN Selecting this word returns the menu to the previous menu.

CANCEL or NO

Selecting this word cancels the operation in the present

menu and returns to the previous menu.

OK or YES

Selecting this word executes the prepared function or shifts

the menu to the next menu.

Operating

EASY MENU

From the EASY MENU, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons. Then

perform it according to the following table.

(continued on next page)

Item Description

ASPECT

Using the ◄/► buttons switches the mode for aspect ratio.

See the ASPECT item in IMAGE menu (



36).

KEYSTONE

Using the ◄/► buttons corrects the vertical keystone distortion.

See the

KEYSTONE item in SETUP menu (



43).

PICTURE MODE

Using the ◄/► buttons switches the picture mode.

The picture modes are combinations of GAMMA and COLOR TEMP

settings. Choose a suitable mode according to the projected source.

NORMAL

CINEMA

DYNAMIC

BOARD(BLACK)

PHOTO

DAYTIME

WHITEBOARD

BOARD(GREEN)

GAMMA COLOR TEMP

NORMAL 1 DEFAULT 2 MID

CINEMA 2 DEFAULT 3 LOW

DYNAMIC 3 DEFAULT 1 HIGH

BOARD(BLACK) 4 DEFAULT 4 Hi-BRIGHT-1

BOARD(GREEN) 4 DEFAULT 5 Hi-BRIGHT-2

WHITEBOARD 5 DEFAULT 2 MID

DAYTIME 6 DEFAULT 6 Hi-BRIGHT-3

PHOTO 7 DEFAULT 7 Hi-BRIGHT-4

• When the combination of GAMMA and COLOR TEMP differs

from pre-assigned modes above, the display on the menu for the

PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and

COLOR TEMP (



33, 34) items in PICTURE menu.

• Lines or other noise might appear on the screen when this function

is operated, but it is not a malfunction.

EASY MENU

Item Description

ECO MODE

Using the ◄/► buttons switches the ECO MODE.

See the ECO MODE item in SETUP menu (



44).

INSTALLATION

Pressing the ► button displays the INSTALLATION dialog.

See the

INSTALLATION

item in SETUP menu (



44).

RESET

Performing this item resets all of the EASY MENU items except the

FILTER TIME and LANGUAGE.

A dialog is displayed for conrmation. Selecting the OK using the ►

button performs resetting.

FILTER TIME

The usage time of the air lter is shown in the menu.

Performing this item resets the lter time which counts usage time

of the air lter.

A dialog is displayed for conrmation. Selecting the OK using the ►

button performs resetting.

See the FILTER TIME item in OPTION menu (



55).

LANGUAGE

Using the ◄/► buttons changes the display language.

See the LANGUAGE item in SCREEN menu (



47).

ADVANCED MENU

Press the ► or ENTER button to use the menu of PICTURE,

IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION or SECURITY.

EXIT Press the ◄ or ENTER button to nish the OSD menu.

PICTURE menu

From the PICTURE menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or ENTER button to

execute the item. Then perform it according to the

following table.

(continued on next page)

Item Description

BRIGHTNESS

Using the

◄/►

buttons adjusts the brightness.

Dark

Light

CONTRAST

Using the

◄/►

buttons adjusts the contrast.

Weak

Strong

GAMMA

Using the ▲/▼ buttons switches the gamma mode.

To adjust CUSTOM

Selecting a mode whose name includes CUSTOM and then

pressing the ► button or the ENTER button displays

a dialog to aid you in adjusting the mode.

This function is useful when you want to

change the brightness of particular tones.

Choose an item using the ◄/► buttons,

and adjust the level using the ▲/▼ buttons.

You can display a test pattern for checking the effect of your

adjustment by pressing the ENTER button.

Each time you press the ENTER button, the

pattern changes as below.

No pattern

Gray scale of 9 steps

Ramp



Gray scale of 15 steps

The eight equalizing bars correspond to eight tone levels of the test

pattern (Gray scale of 9 steps) except the darkest in the left end. If you

want to adjust the 2nd tone from left end on the test pattern, use the

equalizing adjustment bar “1”. The darkest tone at the left end of the

test pattern cannot be controlled with any of equalizing adjustment bar.

• Lines or other noise might appear on the

screen when this function is operated, but it

is not a malfunction.

PICTURE menu

(continued on next page)

Item Description

COLOR TEMP

Using the ▲/▼ buttons switches the color temperature mode.

To adjust CUSTOM

Selecting a mode whose name includes

CUSTOM and then pressing the ► button

or the ENTER button displays a dialog

to aid you in adjusting the OFFSET and

GAIN of the selected mode.

OFFSET adjustments change the color intensity on the whole tones

of the test pattern.

GAIN adjustments mainly affect color intensity on the brighter tones

of the test pattern.

Choose an item using the ◄/► buttons, and adjust the level using

the ▲/▼ buttons.

You can display a test pattern for checking the effect of your

adjustment by pressing the ENTER button.

Each time you press the ENTER button, the pattern changes as below.

No pattern

Gray scale of 9 steps

Ramp



Gray scale of 15 steps

• Lines or other noise might appear on the screen

when this function is operated, but it is not a

malfunction.

COLOR

Using the ◄/► buttons adjusts the strength of whole color.

Weak

Strong

• This item can be selected only for a video and component video

signal.

•

For an HDMI

signal, this item can also be selected if either (1) or (2) applies.

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.

(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

TINT

Using the ◄/► buttons adjusts the tint.

Reddish

Greenish

• This item can be selected only for a video and component video

signal.

•

For an HDMI

signal, this item can also be selected if either (1) or (2) applies.

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.

(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

PICTURE menu

Item Description

SHARPNESS

Using the ◄/► buttons adjusts the sharpness.

Weak

Strong

• There may be some noise and/or the screen may icker for a

moment when an adjustment is made. This is not a malfunction.

MY MEMORY

This projector has 4 memories for adjustment data (for all the items

of the PICTURE menu).

Selecting a function using the ▲/▼ buttons and pressing the ► or

ENTER button performs each function.

SAVE-1

SAVE-2

SAVE-3

SAVE-4

LOAD-4

LOAD-3

LOAD-2

LOAD-1

SAVE-1, SAVE-2, SAVE-3, SAVE-4

Performing a SAVE function saves the current adjustment data into

the memory linked in the number included in the function’s name.

• Remember that the current data being stored of a memory will be

lost by saving new data into the memory.

LOAD-1, LOAD-2, LOAD-3, LOAD-4

Performing a LOAD function loads the data from the memory linked

in the number included in the function’s name, and adjusts the

picture automatically depending on the data.

• The LOAD functions whose linked memory has no data are

skipped.

• Remember that the current adjusted condition will be lost by

loading data. If you want to keep the current adjustment, please

save it before performing a LOAD function.

• There may be some noise and the screen may icker for a

moment when loading data. This is not malfunction.

• You can perform the LOAD function using MY BUTTON. Please

see MY BUTTON item in OPTION menu (



56, 57).

IMAGE menu

From the IMAGE menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or ENTER button to

execute the item. Then perform it according to the

following table.

Item Description

ASPECT

Using the ▲/▼ buttons switches the mode for aspect ratio.

For a computer signal

NORMAL

4:3

16:9

16:10

For an HDMI

signal

NORMAL

4:3

16:9

16:10

14:9

For a video signal or component video signal

4:3

16:9

14:9

For no signal

4:3 (xed)

• The NORMAL mode keeps the original aspect ratio of the signal.

(continued on next page)

IMAGE menu

Item Description

OVER SCAN

Using the ◄/► buttons adjusts the over-scan ratio.

Small (It magnies picture)

Large (It reduces picture)

• This item can be selected only for a video and component video

signal.

• For an HDMI

signal, this item can also be selected if either (1) or

(2) applies.

(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.

(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

V POSITION

Using the ◄/► buttons adjusts the vertical position.

Down

• Over-adjusting the vertical position may cause noise to appear on

the screen. If this occurs, please reset the vertical position to the

default setting. Pressing the RESET button when the V POSITION

is selected will reset the V POSITION to the default setting.

• When this function is performed on a video signal, the range of

this adjustment depends on OVER SCAN (



37) setting. It is not

possible to adjust when OVER SCAN is set to 10.

•

This function is unavailable for signal from the HDMI port.

H POSITION

Using the ◄/► buttons adjusts the horizontal position.

Right

Left

•

Over-adjusting the horizontal position may cause noise to appear on

the screen. If this occurs, please reset the horizontal position to the

default setting. Pressing the RESET button when the H POSITION is

selected will reset the H POSITION to the default setting.

• When this function is performed on a video signal, the range of

this adjustment depends on OVER SCAN (



37) setting. It is not

possible to adjust when OVER SCAN is set to 10.

• This function is unavailable for signal from the HDMI port.

(continued on next page)

IMAGE menu

Item Description

H PHASE

Using the

◄/►

buttons adjusts the horizontal phase to eliminate icker.

Right

Left

• This item can be selected only for a computer signal or a

component video signal. This function is unavailable for signal from

the HDMI port.

H SIZE

Using the ◄/► buttons adjusts the horizontal size.

Small

Large

• This item can be selected only for a computer signal. This function

is unavailable for signal from the HDMI port.

• When this adjustment is excessive, the picture may not be

displayed correctly. In such a case, please reset the adjustment

by pressing the RESET button on the remote control during this

operation.

• Images might appear degraded when this function is operated, but

it is not a malfunction.

AUTO ADJUST

EXECUTE

Selecting this item performs the automatic adjustment feature.

For a computer signal

The vertical position, the horizontal position and the horizontal

phase will be automatically adjusted.

Make sure that the application window is set to its maximum size

prior to attempting to use this feature. A dark picture may still be

incorrectly adjusted. Use a bright picture when adjusting.

For a video signal

The video format best suited for the respective input signal will

be selected automatically. This function is available only when

the AUTO is selected for the VIDEO FORMAT item in the INPUT

menu (



40).

The vertical position and horizontal position will be

automatically set to the default.

For a component video signal

The vertical position and horizontal position will be automatically

set to the default. The horizontal phase will be automatically

adjusted.

• The automatic adjustment operation requires approx. 10 seconds.

Also please note that it may not function correctly with some input.

• When this function is performed for a video signal, a certain extra

such as a line may appear outside a picture.

• When this function is performed for a computer signal, a black

frame may be displayed on the edge of the screen, depending on

the computer model.

• The items adjusted by this function may vary when the FINE or

DISABLE is selected for the AUTO ADJUST item of the SERVICE

item in the OPTION menu (



58).

INPUT menu

From the INPUT menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or ENTER button to

execute the item. Then perform it according to the

following table.

Item Description

PROGRESSIVE

Using the ▲/▼ buttons switches the progress mode.

FILM

OFF

•

This function works only for a video signal, component video signal

(of 480i@60 or 576i@50 or 1080i@50/60) and an HDMI™ signal (of

480i@60 or 576i@50 or 1080i@50/60).

• When TV or FILM is selected, the screen image will be sharp.

FILM adapts to the 2-3 Pull-Down conversion system. But these

may cause a certain defect (for example, jagged line) of the picture

for a quick moving object. In such a case, please select OFF, even

though the screen image may lose sharpness.

VIDEO NR

Using the ▲/▼ buttons switches the noise reduction mode.

HIGH

MID

LOW

•

This function works only for a video signal, component video signal

(of 480i@60 or 576i@50 or 1080i@50/60) and an HDMI™ signal (of

480i@60 or 576i@50 or 1080i@50/60).

COLOR SPACE

Using the ▲/▼ buttons switches the mode for color space.

AUTO

RGB

SMPTE240

REC709

REC601

• This item can be selected only for a computer signal, component

video signal or an HDMI™ signal.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well at some signals. In such a

case, it might be good to select a suitable mode except AUTO.

(continued on next page)

INPUT menu

Item Description

VIDEO FORMAT

The video format for VIDEO port can be set.

(1) Use the ▲/▼ buttons to

select the input port.

(2) Using the ◄/► buttons

switches the mode for video

format.

AUTO

NTSC

PAL

SECAM

N-PAL

M-PAL

NTSC4.43

• This item is performed only for video signal from the VIDEO port.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well for some signals. If the

picture becomes unstable (e.g. an irregular picture, lack of color),

please select the mode according to the input signal.

HDMI FORMAT

Using the ▲/▼ cursor buttons switches the video format for an

input from the HDMI port.

AUTO

VIDEO

COMPUTER

Feature

AUTO automatically sets the optimum mode.

VIDEO sets the suitable mode for DVD signals.

COMPUTER sets the suitable mode for computer signals.

• When the COMPUTER is selected, or when the AUTO is selected

and the projector recognizes that it receives computer signals, the

functions COLOR (PICTURE menu), TINT (PICTURE menu) and

OVER SCAN (IMAGE menu) are unavailable.

HDMI RANGE

Using the ▲/▼ cursor buttons changes the digital range for input

from the HDMI port.

AUTO

NORMAL

ENHANCED

Feature

AUTO automatically sets the optimum mode.

NORMAL s

ets the suitable mode for DVD signals. (16-

235)

ENHANCED

sets the suitable mode for computer signals. (0-255)

• If the contrast of the screen image is too strong or too weak, try

nding a more suitable mode.

(continued on next page)

INPUT menu

Item Description

COMPUTER IN

The computer input signal type for COMPUTER IN1 and IN2 ports

can be set.

(1)

Use the ▲/▼ buttons to select the COMPUTER IN port to be set.

(2) Use the ◄/► buttons to select

the computer input signal type.

(COMPUTER IN1)

AUTO

SYNC ON G OFF

(COMPUTER IN2)

AUTO

SYNC ON G OFF

MONITOR OUT

• Selecting the AUTO mode allows

you to input a sync on G signal or component video signal from the

port (



12).

• In the AUTO mode, the picture may be distorted with certain

input signals. In such a case, remove the signal connector so that

no signal is received and select the SYNC ON G OFF, and then

reconnect the signal.

FRAME LOCK

Set the frame lock function on/off for each port.

(1) Use the ▲/▼ buttons to select

the input ports.

(2) Use the ◄/► buttons to turn the

frame lock function on/off .

OFF

• This item can be performed only on a signal with a vertical

frequency of 49 to 51Hz, 59 to 61 Hz.

• When ON is selected, moving pictures are displayed more

smoothly.

(continued on next page)

INPUT menu

Item Description

RESOLUTION

The resolution for the COMPUTER IN1 and COMPUTER IN2 input

signals can be set on this projector.

(1) In the INPUT menu select the RESOLUTION using the ▲/▼

buttons and press the ► button.

The RESOLUTION menu will be

displayed.

(2) In the RESOLUTION menu select the

resolution you wish to display using

the ▲/▼ buttons.

Selecting AUTO will set a resolution

appropriate to the input signal.

(3) Pressing the ► or ENTER button when

selecting a STANDARD resolution will

automatically adjust the horizontal and

vertical positions, clock phase and

horizontal size.

The INPUT_INFORMATION dialog will be

displayed.

(4) To set a custom resolution use the ▲/▼ buttons to select

the CUSTOM and the RESOLUTION_CUSTOM box will be

displayed.

Set the horizontal (HORZ) and

vertical (VERT) resolutions using

the ▲/▼/◄/► buttons.

This function may not support all

resolutions.

(5) Move the cursor to OK on screen and press the ► or ENTER

button. The message "ARE YOU SURE YOU WISH TO

CHANGE RESOLUTION?" appears. To save the setting, press

the ► button.

The horizontal and vertical positions, clock phase and horizontal

size will be automatically adjusted.

The INPUT_INFORMATION dialog

will be displayed.

(6) To revert back to the previous resolution without saving changes,

move the cursor to CANCEL on screen and press the ◄ or

ENTER button.

The screen will then return to the RESOLUTION menu

displaying the previous resolution.

• For some pictures, this function may not work well.

STANDARD

↓

CUSTOM

↓

SETUP menu

From the SETUP menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or ENTER button to

execute the item. Then perform it according to the

following table.

Item Description

KEYSTONE

Using the ◄/► buttons corrects the vertical keystone distortion.

Shrink the bottom of the image

Shrink the top of the image

• The adjustable range of this function will vary among inputs. For

some input, this function may not work well.

• When the zoom adjustment is set to the TELE (telephoto focus),

this function may be excessive. This function should be used when

the zoom adjustment is set to the full WIDE (wide-angle focus)

whenever possible.

AUTO ECO MODE

Using the ▲/▼ buttons turns on/off the AUTO ECO MODE.

OFF

• When ON is selected, the projector will always be set to Eco mode

at start-up regardless of the ECO MODE (



44) setting. An OSD

message “AUTO ECO MODE” will be displayed for a while when

the projector starts with this function activated.

(continued on next page)

SETUP menu

Item Description

ECO MODE

Using the ▲/▼ buttons switches the ECO MODE.

NORMAL

ECO

INTELLIGENT ECO

SAVER

• When the ECO is selected, acoustic noise and screen brightness

are reduced.

• When INTELLIGENT ECO is selected, the brightness of the

lamp changes according to the level of the input signal. The lamp

becomes brighter when the input signal level is high and darker

when the level is low. If dark images are projected continuously, the

brightness of the lamp may increase to maintain its performance.

• When SAVER is selected, you can select the time within 1 to 30

min. for SAVER MODE using the ► button. If the image signal level

doesn’t change more than the period set, the lamp brightness is

reduced and electric power consumption decreased. If the image

signal level changes or any buttons are operated, the lamp will

brighten again. If dark images are projected continuously, the

brightness of the lamp may increase to maintain its performance.

• When AUTO ECO MODE (



43) is set to ON, the projector will

always be set to Eco mode at start-up regardless this setting.

INSTALLATION

Pressing the ►button displays the dialog for changing the

INSTALLATION setting.

Use the ▲/▼ buttons to select the desired setting on the

INSTALLATION dialog.

(continued on next page)

Item Description

STANDBY MODE

Using ▲/▼ buttons switches the standby mode setting between

NORMAL and SAVING.

NORMAL

SAVING

When SAVING is selected, the power consumption in the standby

mode is lowered with some functional restriction as below:

• The RS-232C communication control is disabled except turning

the projector on and changing the STANDBY MODE setting.

• When SAVING is selected, STANDBY setting of AUDIO SOURCE

(



46) is invalid, no signal is output from AUDIO OUT port and no

sound from a built-in speaker.

• When SAVING is selected, STANDBY setting of MONITOR OUT

is invalid, and no signal is output from MONITOR OUT port in the

standby mode.

MONITOR OUT

While the image signal from the input port chosen in step (1) is

projected, the image signal from the input port selected in step (2) is

output to MONITOR OUT port.

(1) Choose a picture input port using ▲/▼ buttons.

Choose STANDBY to select the picture

output in the standby mode.

(2) By using ◄/► buttons, select

COMPUTER IN 1 port or OFF to disable

the MONITOR OUT port for the input port

or standby mode chosen in the step (1).

• If you have changed the setting of STANDBY, it applies only to

the current standby mode, NORMAL or SAVING, selected under

STANDBY MODE, without changing the setting of the other mode.

The factory settings are as follows:

- COMPUTER IN1 for the NORMAL mode of STANDBY MODE

- OFF for the SAVING mode of STANDBY MODE

• It is invalid if MONITOR OUT is not selected under COMPUTER

IN 2.

SETUP menu

AUDIO menu

From the AUDIO menu, items shown in the table

below can be performed. Select an item using the

▲/▼ cursor buttons, and press the ► cursor button

or the ENTER button to execute the item. Then

perform it according to the following table.

Item Description

VOLUME Using the ◄/► buttons adjusts the volume. Low

High

SPEAKER

Using the ▲/▼ buttons turns on/off the built-in speaker.

OFF

When OFF is selected, the built-in speaker does not work.

AUDIO SOURCE

While the image signal from the input port chosen in step (1) is

projected, the audio signal from the input port selected in step

(2) is output to both the AUDIO OUT port and built-in speaker of

this projector. However, the built-in speaker does not work when

SPEAKER is set to OFF.

(1) Choose a picture input port using the

▲/▼ buttons.

Choose STANDBY to select the sound

output in the standby mode.

(2) Select an audio input port or the mute

icon using the ◄/► buttons.

The icons indicate the following;

No.1: AUDIO IN port No.2: HDMI port

: mutes the sound

• Audio input from port No. 2 can only be selected by HDMI input

port.

• Even if the projector is in the standby mode, cooling fans may

work and make noises when the built-in speaker is in operation.

•

C.C. (Closed Caption) is automatically activated when is selected

and an input signal containing C.C. is received. This function is available

only when the signal is NTSC for VIDEO, or 480i@60 for COMPUTER

IN1 or COMPUTER IN2, and when AUTO is selected for DISPLAY in the

C.C. menu under the SCREEN menu (



52).

SCREEN menu

From the SCREEN menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or ENTER button to

execute the item. Then perform it according to the

following table.

Item Description

LANGUAGE

Using the ▲/▼/◄/► buttons switches the OSD (On Screen

Display) language.

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

(shown in the LANGUAGE dialog)

Press the ENTER or INPUT button to save the language setting.

MENU POSITION

Using the ▲/▼/◄/► buttons adjusts the menu position.

To quit the operation, press the MENU button on the remote control

or keep no operation for about 10 seconds.

BLANK

Using the ▲/▼ buttons switches the mode for the blank screen.

The blank screen is a screen for the temporarily blanking feature

(



28). It is displayed by pressing the BLANK button on the remote

control.

MyScreen

ORIGINAL

BLUE

WHITE

BLACK

MyScreen :

Screen can be registered by the MyScreen item (



48).

ORIGINAL : Screen preset as the standard screen.

BLUE, WHITE, BLACK : Plain screens in each color.

• To avoid remaining as an afterimage, the MyScreen or ORIGINAL

screen will change to the AUTO BLANK screen after several

minutes.

AUTO BLANK

Using the ▲/▼ buttons switches the mode for the AUTO BLANK

screen.

BLUE

WHITE

BLACK

• To avoid remaining as an afterimage, displayed image will change

to the designated blank color screen by AUTO BLANK after several

minutes at the following conditions.

- When MyScreen or ORIGINAL is displayed as BLANK screen.

- When start-up screen is displayed.

(continued on next page)

SCREEN menu

Item Description

START UP

Using the ▲/▼ buttons switches the mode for the start-up screen.

The start-up screen is a screen displayed when no signal or an

unsuitable signal is detected.

MyScreen

ORIGINAL

OFF

MyScreen :

Screen can be registered by the MyScreen item

(



below

ORIGINAL : Screen preset as the standard screen.

OFF : Plain black screen.

• To avoid remaining as an afterimage, the START UP screen will

change to the AUTO BLANK screen after several minutes.

• When the ON is selected to the MyScreen PASSWORD item in

the SECURITY menu (



61), the START UP is fixed to MyScreen.

MyScreen

This item allows you to capture an image for use as a MyScreen

image which can be used as the BLANK screen and START UP

screen. Display the image you want to capture before executing the

following procedure.

Selecting this item displays a dialog

titled “MyScreen”. It will ask you if

you start capturing an image from the

current screen. Please wait for the

target image to be displayed, and press

the ENTER or INPUT button to start

registration.

To restore the screen and return to

the previous dialog, press the RESET

button on the remote control.

Registration may take several minutes.

When the registration is completed,

the registered screen and the following

message is displayed for several

seconds:

“MyScreen registration is nished.”

If the registration failed, the following message is displayed:

“A capturing error has occurred. Please try again.”

• This function cannot be selected when the ON is selected to the

MyScreen Lock item (



49).

• This function cannot be selected when the ON is selected to the

MyScreen PASSWORD item in SECURITY menu (



61).

•

This function is unavailable for signal from the HDMI port.

(continued on next page)

SCREEN menu

Item Description

MyScreen Lock

Using the ▲/▼ buttons turns on/off the MyScreen lock function.

OFF

When the ON is selected, the item MyScreen is locked. Use this

function for protecting the current MyScreen.

• This function cannot be selected when the ON is selected to the

MyScreen PASSWORD item in SECURITY menu (



61).

MESSAGE

Using the ▲/▼ buttons turns on/off the message function.

OFF

When the ON is selected, the following message function works.

“AUTO IN PROGRESS” while automatically adjusting

“NO INPUT IS DETECTED”

“SYNC IS OUT OF RANGE”

“INVALID SCAN FREQ.”

“NOT AVAILABLE.”

“Searching….” while searching for the input

“Detecting….” while an input signal is detected

“AUTO ECO MODE” while starting up with AUTO ECO MODE

The indication of the input signal displayed by changing

The indication of the aspect ratio displayed by changing

The indication of the PICTURE MODE displayed by changing

The indication of the MY MEMORY displayed by changing

The indication of “FREEZE” and “II” while freezing the screen by

pressing the FREEZE button.

The indication of the TEMPLATE displayed by changing.

The indication of the ECO MODE displayed by changing.

• When the OFF is selected, please remember if the picture is

frozen. Do not mistake freezing for a malfunction (



28).

(continued on next page)

SCREEN menu

Item Description

SOURCE NAME

Each input port for this projector can have a name applied to it.

(1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE

NAME and press the ► or ENTER button.

The SOURCE NAME menu will be displayed.

(2) Use the ▲/▼ buttons on the SOURCE

NAME menu to select the port to be

named and press the ► button. The

SOURCE NAME dialog will be displayed.

Right side of the menu is blank until a

name is specied.

(3) Select an icon you would like to assign to

the port in the SOURCE NAME dialog.

The name assigned to the port will also

be automatically switched according to

your icon selection. Press the ENTER or

INPUT button to determine your icon selection.

(4) Select a number you would like to assign

to the port along with the icon. You can

select the number either from blank

(no number assigned), 1, 2, 3, or 4.

Then press the ENTER or INPUT button.

(5) If you would like to modify the name assigned

to the port, select CUSTOM NAME and

press the ENTER or INPUT button.

(continued on next page)

SCREEN menu

Item Description

SOURCE NAME

(continued)

(6) The current name will be displayed on

the rst line. Use the ▲/▼/◄/► buttons

and the ENTER or INPUT button to

select and enter characters. To erase 1

character at one time, press the RESET

button or press the ◄ and INPUT button

at the same time. Also if you move the

cursor to DELETE or ALL CLEAR on

screen and press the ENTER or INPUT

button, 1 character or all characters will

be erased. The name can be a maximum

of 16 characters.

(7) To change an already inserted character,

press the ▲ button to move the cursor to

the rst line, and use the ◄/► buttons to

move the cursor on the character to be

changed.

After pressing the ENTER or INPUT button, the character is

selected. Then, follow the same procedure as described at the

item (6) above.

(8) To nish entering text, move the cursor to the OK on screen and

press the ►, ENTER or INPUT button. To revert to the previous

name without saving changes, move the cursor to the CANCEL

on screen and press the ◄, ENTER or INPUT button.

TEMPLATE

Using the ▲/▼ cursor buttons switches the mode for the template

screen.

Press the ► cursor (or the ENTER) button to display the selected

template, and press the ◄ cursor button to close the displayed

screen.

The last selected template is displayed when the MY BUTTON

allocated to the TEMPLATE function is pressed (



57).

TEST PATTERN

DOT-LINE1

DOT-LINE2

DOT-LINE3



MAP2

MAP1

CIRCLE2

CIRCLE1

DOT-LINE4

You can turn a map upside down and scroll it horizontally when

MAP1 or MAP2 is selected. To invert or scroll the map, display

the guidance by pressing the RESET button on the remote three

seconds or more when MAP1 or MAP2 appears.

(continued on next page)

SCREEN menu

Item Description

C.C.

(Closed Caption)

The C.C. is the function that displays a

transcript or dialog of the audio portion of

a video, les or other presentation or other

relevant sounds. It is required to have NTSC

format video or 480i@60 format component

video source supporting C.C. feature to

utilize this function.

It may not work properly, depending on equipment or signal source.

In this case, please turn off the Closed Caption.

DISPLAY

Select Closed Caption DISPLAY setting from following options using

▲/▼ buttons.

AUTO

OFF

AUTO : Closed Caption automatically displays when the volume

is muted.

ON : Closed Caption is on.

OFF : Closed Caption is off.

• The caption is not displayed when the OSD menu is active.

• The Closed Caption is the function to display the dialogue,

narration, and / or sound effects of a television program or other

video sources. The Closed Caption availability is depending upon

broadcaster and/or content.

MODE

Select Closed Caption MODE setting from following options using

▲/▼ buttons.

CAPTIONS

TEXT

CAPTIONS : Display Closed Caption.

TEXT : Display Text data, which is for additional information such

as news reports or a TV program guide. The information

covers the entire screen. Not all of the C.C. program has

Text information.

CHANNEL

Select Closed Caption CHANNEL from following options using ▲/▼

buttons.

1: Channel 1, primary channel / language

2: Channel 2

3: Channel 3

4: Channel 4

The channel data may vary, depending on the content. Some

channel might be used for secondary language or empty.

OPTION menu

From the OPTION menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or ENTER button to execute

the item, except for the items LAMP TIME and FILTER

TIME. Then perform it according to the following table.

Item Description

AUTO SEARCH

Using the ▲/▼ buttons turns on/off the automatic signal search

function.

OFF

When the ON is selected, detecting no signal automatically cycles

through input ports in the following order. The search is started from

the current port. Then when an input is found, the projector will stop

searching and display the image.

COMPUTER IN1

COMPUTER IN2

VIDEO



HDMI

DIRECT POWER

Using the ▲/▼ buttons turns on/off the DIRECT POWER ON

function.

OFF

When set to the ON, the lamp in projector will be automatically turned

on without the usual procedure (



18), only when the projector is

supplied with the power after the power was cut while the lamp was on.

• This function does not work as long as the power has been

supplied to the projector while the lamp is off.

•

After turning the lamp on by the DIRECT

POWER

ON function,

if neither input nor operation is detected for about 30 minutes, the

projector is turned off, even though the AUTO

POWER

OFF function

(



54) is disabled.

(continued on next page)

OPTION menu

Item Description

AUTO POWER

OFF

Using the ▲/▼ buttons adjusts the time to count down to

automatically turn the projector off.

Long (max. 99 minutes)

Short (min. 0 minute = DISABLE)

When the time is set to 0, the projector is not turned off automatically.

When the time is set to 1 to 99, and when the passed time with

no-signal or an unsuitable signal reaches at the set time, the

projector lamp will be turned off.

If one of the projector's buttons or the remote control buttons

is pressed or one of the commands (except get commands) is

transmitted to the CONTROL port during the corresponding time,

the projector will not be turned off.

Please refer to the section Turning off the power

(



19).

(continued on next page)

OPTION menu

Item Description

LAMP TIME

The lamp time is the usage time of the lamp, counted after the last

resetting. It is shown in the OPTION menu.

Pressing the RESET button on the remote control or the ► button

of the projector displays a dialog.

To reset the lamp time, select the OK using the ► button.

CANCEL

• Please reset the lamp time only when you have replaced the lamp,

for a suitable indication about the lamp.

•

For the lamp replacement, see the section Replacing the lamp

(



65).

FILTER TIME

The lter time is the usage time of the air lter, counted after the last

resetting. It is shown in the OPTION menu.

Pressing the RESET button on the remote control or the ► button

of the projector displays a dialog.

To reset the lter time, select the OK using the ► button.

CANCEL

•

Please reset the lter time only when you have cleaned or replaced

the air lter, for a suitable indication about the air lter.

• For the air lter cleaning, see the section Cleaning and replacing

the air lter (



67).

(continued on next page)

OPTION menu

Item Description

MY BUTTON

This item is to assign one of the following functions to MY BUTTON

1/2 on the remote control (



6).

(1) Use the ▲/▼ buttons on the MY BUTTON menu to select a MY

BUTTON - (1/2) and press the ► or ENTER button to display the

MY BUTTON setup dialog.

(2) Then using the ▲/▼/◄/► buttons sets one of the following

functions to the chosen button. Press the ENTER or INPUT

button to save the setting.

• COMPUTER IN1: Selects the input from COMPUTER IN1 port.

• COMPUTER IN2: Selects the input from COMPUTER IN2 port.

• HDMI: Selects input from HDMI port.

• VIDEO: Selects the input from VIDEO port.

• INFORMATION: Displays SYSTEM_INFORMATION, INPUT_

INFORMATION (



59) or nothing.

• MY MEMORY: Loads one of adjustment data stored (



35).

When more than one data are saved, the adjustment

changes every time the MY BUTTON is pressed.

When no data is saved in memory, the

dialog "No saved data" appears.

When the current adjustment is not

saved to memory, the dialog as shown in

the right appears.

If you want to keep the current adjustment, please press

the ► button to exit. Otherwise loading a data will overwrite the

current adjusted condition.

(continued on next page)

OPTION menu

Item Description

MY BUTTON

(continued)

• PICTURE MODE: Changes the PICTURE MODE (



31).

•

FILTER RESET: Displays the lter time reset conrmation dialogue

(



55).

• TEMPLATE: Makes the template pattern selected to the

TEMPLATE item (



51) appear or disappear.

• AV MUTE: Turns the picture and audio on/off.

• RESOLUTION: Turns on/off the RESOLUTION dialog (



42).

• ECO MODE: Changes the ECO MODE (



44).

•

SAVER MODE:

Changes the SAVER MODE

(



44 ECO MODE).

MY SOURCE

Using ▲/▼ buttons selects the picture input port to be selected with

pressing the MY SOURCE/DOC.CAMERA button on the remote

control.

You can use this function not only for document cameras but also

computers and other equipment.

VIDEO

COMPUTER IN1

COMPUTER IN2

HDMI

SERVICE

Selecting this item displays the SERVICE

menu.

Select an item using the ▲/▼ buttons,

and press the ► button or the ENTER

button on the remote control to execute

the item.

ALTITUDE

Using the ▲/▼ buttons switches the rotation speed of the cooling fans.

The HIGH is the mode for use at highlands etc. If the projector is used

at an altitude of about 1600 m (5250 feet) or higher, select HIGH.

Otherwise, select NORMAL. Note that the projector is noisier when the

HIGH is selected.

HIGH

NORMAL

(continued on next page)

OPTION menu

Item Description

SERVICE

(continued)

AUTO ADJUST

Using the ▲/▼ buttons to select one of the mode. When the

DISABLE is selected, the automatic adjustment feature is disabled.

FINE

FAST

DISABLE

FINE: Finer tuning including H.SIZE adjustment.

FAST: Faster tuning, setting H.SIZE to prearranged data for the

input signal.

•

Depending on conditions, such as input image, signal cable to the

projector, environment around the projector, etc., the automatic adjustment

may not work correctly. In such a case, please choose DISABLE to

disable the automatic adjustment, and make adjustment manually.

GHOST

Adjust the settings using the ▲/▼ buttons to eliminate ghosting.

FILTER MESSAGE

Use the ▲/▼ button to set the timer for notifying by the message

when to replace the lter unit

100h

·········

5000h

OFF

After choosing an item except OFF, the message “REMINDER ***

HRS PASSED ....” will appear after the timer reaches the interval

time set by this feature (



71).

When the OFF is chosen, the message will not appear. Utilize this

feature to keep the air lter clean, setting the suitable time according

to your environment of this projector.

• Please take care of the lter unit periodically, even if there is

no message. If the air lter becomes to be blocked by dust or

other matter, the internal temperature will rise, which could cause

malfunction, or reduce the lifetime of the projector.

• Please be careful with the operating environment of the projector

and the condition of the lter unit.

KEY LOCK

(1) Use the ▲/▼ buttons to choose the operations control.

CONTROL PANEL

REMOTE CONTROL

(2)

Use the ◄/► buttons to select ON or OFF.

OFF

Selecting ON in Step 2 locks the buttons except STANDBY/ON on

the operations control selected in Step 1. Selecting OFF releases

the locked buttons on the operations control selected in Step 1.

• Please use this function to prevent tampering or accidental

operation.

(continued on next page)

OPTION menu

Item Description

SERVICE

(continued)

REMOTE FREQ.

(1) Use the ▲/▼ button to change the projector's remote sensor

frequency setting (



17).

1:NORMAL

2:HIGH

(2) Use the ◄/► button to change the

projector's remote sensor on or off.

OFF

The factory default setting is for both 1:NORMAL and 2:HIGH to be on.

If the remote control does not function correctly, disable either of them.

It's not possible to disable both options at the same time.

INFORMATION

Selecting this item displays a dialog titled “INPUT_INFORMATION”.

It shows the information about the current input.

• The “FRAME LOCK” message on the dialog means the frame lock

function is working.

• This item can't be selected for no signal and sync out.

• When the MY TEXT DISPLAY is set to ON, the MY TEXT is

displayed together with the input information in the

INPUT_INFORMATION box (



64).

FACTORY RESET

Selecting OK using the ► button performs this function. By this

function, all the items in all of menus will collectively return to the

initial setting. Note that the items LAMP TIME, FILTER TIME,

LANGUAGE, FILTER MESSAGE and SECURITY settings are not

reset.

CANCEL

Be sure to set ALTITUDE after resetting all the settings (



57).

SECURITY menu

(continued on next page)

This projector is equipped with security functions.

From the SECURITY menu, items shown in the table

below can be performed.

To use SECURITY menu: User registration is required

before using the security functions.

Enter to the SECURITY menu

1. Press the ► button. The ENTER PASSWORD box will be displayed.

2. Use the ▲/▼/◄/► buttons to enter the registered password.

The factory default password is as follows.

This password can be changed

(



below)

. Move the cursor to

the right side of the ENTER PASSWORD box and press

the ► button to display the SECURITY menu.

• It is strongly recommended the factory default password to be

changed as soon as possible.

• If an incorrect password is input, the ENTER PASSWORD box

will be displayed again. If incorrect password is input 3 times, the

projector will turn off. Afterwards the projector will turn off every time

an incorrect password is input.

3. Items shown in the table below can be performed.

If you have forgotten your password

(1) While the ENTER PASSWORD box is displayed, press and hold the

RESET button on the remote control for about 3 seconds or press

and hold the INPUT button for 3 seconds while pressing the ►

button on the projector.

(2) The 10 digit Inquiring Code will be displayed. Contact your dealer

with the 10 digit Inquiring Code. Your password will be sent after your user registration information

is conrmed.

• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will

close. If necessary, repeat the process from (1).

Item Description

SECURITY

PASSWORD

CHANGE

(1) Use the ▲/▼ buttons on the SECURITY menu

to select SECURITY PASSWORD CHANGE

and press the ► button to display the ENTER

NEW PASSWORD box.

(2) Use the ▲/▼/◄/► buttons to enter the new password.

(3) Move the cursor to the right side of the

ENTER NEW PASSWORD box and press the

► button to display the NEW PASSWORD

AGAIN box, enter the same password again.

(4)

Move the cursor to the right side of the NEW

PASSWORD AGAIN box and press the ►

button and the NOTE NEW PASSWORD box

will be displayed for about 30 seconds, please

make note of the password during this time.

Pressing the ENTER button on the remote control or

►

button on the

projector will close the NOTE NEW PASSWORD box.

• Please do not forget your password.

SECURITY menu

5702

SECURITY menu

Item Description

MyScreen

PASSWORD

The MyScreen PASSWORD function can be used to prohibit access to the

MyScreen function and prevent the currently registered MyScreen image

from being overwritten.

1 Turning on the MyScreen PASSWORD

1-1 Use the ▲/▼ buttons on the SECURITY menu to

select MyScreen PASSWORD and press the ►

button to display the MyScreen PASSWORD on/

off menu.

1-2 Use the ▲/▼ buttons on the MyScreen

PASSWORD on/off menu to select ON.

The ENTER NEW PASSWORD box (small)

will be displayed.

1-3 Use the ▲/▼/◄/► buttons to enter the

password. Move the cursor to the right side

of the ENTER NEW PASSWORD box (small)

and press the ► button to display the NEW

PASSWORD AGAIN box, enter the same

PASSWORD again.

1-4 Move the cursor to the right side of the

NEW PASSWORD AGAIN box and press

the ► button to display the NOTE NEW

PASSWORD box for about 30 seconds,

please make note of the password during

this time.

Pressing the ENTER button on the remote control or ► button on the

projector will return to MyScreen PASSWORD on/off menu.

When a password is set for MyScreen:

•

The MyScreen registration function (and menu) will be unavailable.

•

The MyScreen Lock menu will be unavailable.

•

The START UP setting will be locked on MyScreen (and the menu will be

unavailable).

Turning the MyScreen PASSWORD off will allow normal operation of these

functions.

•

Please do not forget your MyScreen PASSWORD.

2 Turning off the MyScreen PASSWORD

2-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off

menu.

2-2

Select OFF to display the ENTER

PASSWORD box (large). Enter the registered

password and the screen will return to the

MyScreen PASSWORD on/off menu.

If an incorrect PASSWORD is input, the menu will

close. If necessary, repeat the process from 2-1.

3 If you have forgotten your password

3-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off

menu.

3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit

Inquiring Code will be displayed inside the box.

3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will

be sent after your user registration information is conrmed.

(continued on next page)

ENTER NEW PASSWORD

box (small)

ENTER PASSWORD box

(large)

SECURITY menu

Item Description

PIN LOCK

PIN LOCK is a function which prevents the projector from being used unless

a registered Code is input.

1 Turning on the PIN LOCK

1-1 Use the ▲/▼ buttons on the SECURITY menu to

select PIN LOCK and press the ► button or the

ENTER button to display the PIN LOCK on/off

menu.

1-2 Use the ▲/▼ buttons on the PIN LOCK on/

off menu to select ON and the Enter PIN

Code box will be displayed.

1-3 Input a 4 part PIN code using the ▲/▼/◄/►,

COMPUTER or INPUT button.

The PIN Code again box will appear. Reenter

the same PIN code. This will complete the PIN

code registration.

•

If there is no key input for about 55 seconds

while the Enter PIN Code box or the PIN Code again box is displayed,

the menu will close. If necessary, repeat the process from 1-1.

Afterwards, anytime the projector is restarted after AC power is turned off

the Enter PIN Code box will be displayed. Enter the registered PIN code.

The projector can be used after entering the registered PIN code. If an

incorrect PIN code is input, the Enter PIN code box will be displayed again.

If an incorrect PIN code is input 3 times, the projector will turn off. Afterwards

the projector will turn off every time an incorrect PIN code is input. The

projector will also turn off if there is no key input for about 5 minutes while

the Enter PIN code box is displayed.

This function will activate only when the projector is started after AC power

is turned off.

•

Please do not forget your PIN code.

2 Turning off the PIN LOCK

2-1 Follow the procedure in 1-1 to display the PIN LOCK on/off menu.

2-2 Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be

displayed.

Enter the registered PIN code to turn the PIN LOCK function off.

If an incorrect PIN code is input 3 times, the projector will turn off.

3 If you have forgotten your PIN code

3-1 While the Enter PIN code box is displayed, press and hold the RESET

button for three seconds or press and hold the INPUT button for 3

seconds while pressing the ► button on the projector.

The 10 digit Inquiring Code will be displayed.

•

If there is no key input for about 5 minutes

while the Inquiring Code is displayed, the

projector will turn off.

3-2 Contact your dealer with the 10 digit Inquiring Code. Your PIN code will

be sent after your user registration information is conrmed.

(continued on next page)

SECURITY menu

Item Description

MY TEXT

PASSWORD

The MY TEXT PASSWORD function can prevent the MY TEXT from being

overwritten. When the password is set for the MY TEXT;

• The MY TEXT DISPLAY menu will be unavailable, which can prohibit

changing the DISPLAY setting.

• The MY TEXT WRITING menu will be unavailable, which can prevent the

MY TEXT from being overwritten.

1 Turning on the MY TEXT PASSWORD

1-1 Use the ▲/▼ buttons on the SECURITY menu to

select the MY TEXT PASSWORD and press the

► button to display the MY TEXT PASSWORD

on/off menu.

1-2 Use the ▲/▼ buttons on the MY TEXT

PASSWORD on/off menu to select ON. The

ENTER NEW PASSWORD box (small) will

be displayed.

1-3 Use the ▲/▼/◄/► buttons to enter the

password. Move the cursor to the right side

of the ENTER NEW PASSWORD box (small)

and press the ► button to display the NEW

PASSWORD AGAIN box, and then enter the

same password again.

1-4 Move the cursor to the right side of the

NEW PASSWORD AGAIN box and press

► button to display the NOTE NEW

PASSWORD box for about 30 seconds, then

please make note of the password during

this time.

Pressing the ENTER button on the remote control or ► button on the

projector will return to the MY TEXT PASSWORD on/off menu.

2 Turning off the MY TEXT PASSWORD

2-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off

menu.

2-2 Select OFF to display the ENTER

PASSWORD box (large). Enter the

registered password and the screen will

return to the MY TEXT PASSWORD on/off

menu.

If an incorrect password is input, the menu will close.

If necessary, repeat the process from 2-1

3 If you have forgotten your password

3-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off

menu.

3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit

inquiring code will be displayed inside the box.

3-3 Contact your dealer with the 10 digit inquiring code. Your password will

be sent after your user registration information is conrmed.

(continued on next page)

ENTER NEW PASSWORD

box (small)

ENTER PASSWORD box

(large)

SECURITY menu

Item Description

MY TEXT

DISPLAY

(1) Use the ▲/▼ buttons on the SECURITY menu to

select the MY TEXT DISPLAY and press the ► or

ENTER button to display the MY TEXT DISPLAY

on/off menu.

(2) Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select

on or off.

OFF

When it is set ON, the MY TEXT will be displayed

on the START UP screen and the INPUT_

INFORMATION when the INFORMATION on the

SERVICE menu is chosen.

• This function is available only when the MY TEXT

PASSWORD function is set to the OFF.

MY TEXT

WRITING

(1) Use the ▲/▼ buttons on the

SECURITY menu to select the MY

TEXT WRITING and press the ►

button. The MY TEXT WRITING dialog

will be displayed.

(2) The current MY TEXT will be displayed

on the rst 3 lines. If not yet written, the

lines will be blank.

Use the ▲/▼/◄/► buttons and the

ENTER or INPUT button to select and

enter characters. To erase 1 character

at one time, press the RESET button or

press the ◄ and INPUT button at the

same time. Also if you move the cursor

to DELETE or ALL CLEAR on screen

and press the ENTER or INPUT button,

1 character or all characters will be

erased. The MY TEXT can be input up

to 24 characters on each line.

(3)

To change an already inserted character,

press the ▲/▼ button to move the

cursor to one of the rst 3 lines, and use

the ◄/► buttons to move the cursor on

the character to be changed.

After pressing the ENTER or INPUT button, the character is selected.

Then, follow the same procedure as described at the item (2) above.

(4) To nish entering text, move the cursor to the OK on screen and press

the ►, ENTER or INPUT button. To revert to the previous MY TEXT

without saving changes, move the cursor to the CANCEL on screen and

press the ◄, ENTER or INPUT button.

•

The MY TEXT WRITING function is available only when the MY TEXT

PASSWORD function is set to OFF.

Maintenance

A lamp has nite product life. Using the lamp for long periods of time could cause

the pictures darker or the color tone poor. Note that each lamp has a different

lifetime, and some may burst or burn out soon after you start using them.

Preparation of a new lamp and early replacement are recommended. To prepare

a new lamp, make contact with your dealer and tell the lamp type number.

Replacing the lamp

Type number : DT01433

Turn the projector off, and unplug the power cord.

Allow the projector to cool for at least 45 minutes.

Prepare a new lamp. If the projector is mounted on

a ceiling, or if the lamp has broken, also ask the

dealer to replace the lamp.

Loosen the screw (marked by arrow) of the lamp

cover and then slide and lift the lamp cover to the

side to remove it.

Loosen the 2 screws (marked by arrow) of the lamp,

and slowly pick up the lamp by the handle.

Never loosen any other screws.

Insert the new lamp, and retighten rmly the 2

screws of the lamp that are loosened in the previous

process to lock it in place.

While putting the interlocking parts of the lamp cover

and the projector together, slide the lamp cover back in

place. Then rmly fasten the screw of the lamp cover.

Turn the projector on and reset the lamp time using

the LAMP TIME item in the OPTION menu.

In case of replacement by yourself, follow the

following procedure.

Replacing the lamp

(4)

Point at the LAMP TIME using the ▼/▲ button, then press the ► button. A dialog will appear.

(5)

Press the ► button to select “OK” on the dialog. It performs resetting the lamp time.

• Please reset the lamp time only when you have replaced the lamp,

for a suitable indication about the lamp.

NOTE

►Do not touch any inner space of the projector, while the lamp

is taken out.

CAUTION

(1) Press the MENU button to display a menu.

(2)

Point at the ADVANCED MENU in the menu using

the ▼/▲ button, then press the ► button.

(3)

Point at the OPTION in the left column of the menu

using the ▼/▲button, then press the ► button.

Handle

lamp cover

Maintenance

Lamp warning

Replacing the lamp (continued)

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

►

The projector uses a high-pressure mercury glass lamp. The lamp

can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or

worn over time. Note that each lamp has a different lifetime, and some may burst or

burn out soon after you start using them. In addition, if the bulb bursts, it is possible

for shards of glass to y into the lamp housing, and for gas containing mercury and

dust containing ne particles of glass to escape from the projector’s vent holes.

►About disposal of a lamp: This product contains a mercury lamp; do not put

it in a trash. Dispose of it in accordance with environmental laws.

• For lamp recycling, go to www.lamprecycle.org (in the US).

• For product disposal, consult your local government agency

or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

WARNING

• If the lamp should break (it will make a loud bang when it does),

unplug the power cord from the outlet, and make sure to request a

replacement lamp from your local dealer. Note that shards of glass

could damage the projector’s internals, or cause injury during handling,

so please do not try to clean the projector or replace the lamp yourself.

•

If the lamp should break (it will make a loud bang when it does), ventilate the

room well, and make sure not to inhale the gas or ne particles that come out

from the projector's vent holes, and not to get them into your eyes or mouth.

• Before replacing the lamp, turn the projector off and unplug the power

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

Handling the lamp while hot can cause burns, as well as damaging the lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp cover while the projector is suspended from

a ceiling. This is dangerous, since if the lamp’s bulb has broken, the

shards will fall out when the cover is opened. In addition, working in

high places is dangerous, so ask your local dealer to have the lamp

replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp

replacing, make sure that the screws are screwed in firmly. Loose

screws could result in damage or injury.

• Use only the lamp of the specified type. Use of a lamp that does not

meet the lamp specications for this model could cause a re, damage or

shorten the life of this product.

• If the lamp breaks soon after the first time it is used, it is possible

that there are electrical problems elsewhere besides the lamp. If this

happens, consult your local dealer or a service representative.

•

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

•

Using the lamp for long periods of time, could cause it dark, not to light up or to burst.

When the pictures appear dark, or when the color tone is poor, please replace the

lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.

Disconnect

the plug

from the

power

outlet

Maintenance

Cleaning and replacing the air  lter

(continued on next page)

Please check and clean the air  lter periodically. When the indicators or a message

prompts you to clean the air  lter, comply with it as soon as possible. The air  lter has two

kinds of  lters inside. Replace the  lters when they are damaged or too soiled. To prepare

the new  lters, make contact with your dealer and tell the following type number.

Type number : UX38851 (Filter set)

When you replace the lamp, please replace the air  lter. An air

 lter of speci ed type will come together with a replacement

lamp for this projector.

Turn the projector off, and unplug the power cord. Allow the

projector to suf ciently cool down.

Use a vacuum cleaner on and around the  lter cover.

Pick and pull up the  lter cover knobs to take it off.

Use a vacuum cleaner for the  lter vent of the projector.

Take the  ne  lter out while holding the  lter cover. It is

recommended to leave the coarse  lter in the  lter cover

as it is.

Use a vacuum cleaner on both sides of the  ne  lter

while holding it so it will not be sucked in. Use a vacuum

cleaner for the inside of the  lter cover to clean up the

coarse  lter. If the  lters are damaged or heavily soiled,

replace them with new ones.

Place the  ne  lter on the coarse one.

Install the  lter unit back into the projector.

Filter cover

Filter cover knobs

Intake vent

Fine  lter

Coarse  lter

Maintenance

Cleaning and replacing the air lter (continued)

Turn the projector on and reset the lter time using the FILTER TIME item in

the EASY MENU.

►Before taking care of the air lter, make sure the power cable

is not plugged in, then allow the projector to cool sufciently. Taking care of the

air lter in a high temperature state of the projector could cause an electric shock,

a burn or malfunction to the projector.

►Use only the air lter of the specied type. Do not use the projector without the

air lter or the lter cover. It could result in a re or malfunction to the projector.

►Clean the air lter periodically. If the air lter becomes clogged by dust or the

like, internal temperatures rise and could cause a re, a burn or malfunction to

the projector.

WARNING

• Please replace the air lter when it is damaged or heavily soiled.

• When you replace the projection lamp, please replace the air lter. An air lter

of specied type will come together with a replacement lamp for this projector.

• Please reset the lter time only when you have cleaned or replaced the air

lter, for a suitable indication about the air lter.

• The projector may display the message such as “CHECK THE AIR FLOW” or

turn off the projector, to prevent the internal heat level rising.

NOTE

(1) Press the MENU button to display a menu.

(2) Point at the FILTER TIME using the ▼/▲ button, then press the ► button.

A dialog will appear.

(3) Press the ► button to select “OK” on the dialog. It performs resetting the

lter time.

Maintenance

Other care

In order to ensure the safe use of your projector, please have it cleaned and

inspected by your dealer about once every year.

Turn the projector off, and unplug the power cord. Allow the projector to cool

sufciently.

After making sure that the projector is cool adequately, lightly wipe the lens

with a commercially available lens-cleaning wipe. Do not touch the lens

directly with your hand.

If the lens is awed, soiled or fogged, it could cause deterioration of display

quality. Please take care of the lens, being cautious of handling.

►Before caring, make sure the power cord is not plugged in,

and then allow the projector to cool sufciently. The care in a high temperature

state of the projector could cause a burn and/or malfunction to the projector.

►Never try to care for the inside of the projector personally. Doing is so

dangerous.

►Avoid wetting the projector or inserting liquids in the projector. It could result in

a re, an electric shock, and/or malfunction to the projector.

• Do not put anything containing water, cleaners or chemicals near the projector.

• Do not use aerosols or sprays.

WARNING

►Please take right care of the projector according to the

following. Incorrect care could cause not only an injury but adverse inuence

such as discoloration, peeling paint, etc.

►Do not use cleaners or chemicals other than those specied in this manual.

►Do not polish or wipe with hard objects.

NOTICE ►Do not directly touch the lens surface with hands.

CAUTION

Inside of the projector

Caring for the lens

Turn the projector off, and unplug the power cord. Allow the projector to cool

sufciently.

After making sure that the projector is cool adequately, lightly wipe with gauze

or a soft cloth.

If the projector is extremely dirty, dip soft cloth in water or a neutral cleaner

diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a

soft, dry cloth.

Incorrect care could have adverse inuence such as discoloration, peeling paint,

etc.

Caring for the cabinet and remote control

Troubleshooting

If an abnormal operation should occur, stop using the projector immediately.

Otherwise if a problem occurs with the projector, the following checks and measures are

recommended before requesting repair.

If this does not resolve the problem, please contact your dealer or service company. They

will tell you what warranty condition is applied.

►

Never use the projector if abnormal operations such as smoke,

strange odor, excessive sound, damaged casing or elements or cables, penetration

of liquids or foreign matter, etc. should occur. In such cases, immediately disconnect

the power plug from the power outlet. After making sure that the smoke or odor has

stopped, contact to your dealer or service company.

WARNING

Related messages

When some message appears, check and cope with it according to the following table.

Although these messages will be automatically disappeared around several minutes, it will

be reappeared every time the power is turned on.

Message Description

There is no input signal.

Please conrm the signal input connection, and the status

of the signal source.

The horizontal or vertical frequency of the input signal is

not within the specied range.

Please conrm the specs for your projector or the signal

source specs.

An improper signal is input.

Please conrm the specs for your projector or the signal

source specs.

(continued on next page)

Troubleshooting

Message Description

The internal temperature is rising. The projector is

operating in low power.

Please turn the power off, and allow the projector to cool

down at least 20 minutes. After having conrmed the

following items, please turn the power ON again.

• Is there blockage of the air passage aperture?

• Is the air lter dirty? If so, please clean or replace the air

lter (



67 ~ 68).

• Does the peripheral temperature exceed 35°C?

• If the projector is used at an altitude of about 1600 m (5250

feet) or higher, set ALTITUDE of the SERVICE item in the

OPTION menu to HIGH (



57).

If the projector is used with a wrong setting, it may cause

damage to the projector itself or the parts inside.

A note of precaution when cleaning the air lter.

Please immediately turn the power off, and clean or change

the air lter referring to the Cleaning and replacing the

air lter section of this manual. After you have cleaned or

changed the air lter, please be sure to reset the lter timer

(



55, 67).

The button operation is not available.

Troubleshooting

Related messages (continued)

Troubleshooting

Regarding the indicator lamps

When operation of the LAMP, TEMP and POWER indicators differs from usual,

check and cope with it according to the following table.

POWER

indicator

LAMP

indicator

TEMP

indicator

Description

Lighting

In Orange

Turned

off

Turned

off

The projector is in a standby state.

Please refer to the section “Power on/off”.

Blinking

In Green

Turned

off

Turned

off

The projector is warming up.

Please wait.

Lighting

In Green

Turned

off

Turned

off

The projector is in an on state.

Ordinary operations may be performed.

Blinking

In Orange

Turned

off

Turned

off

The projector is cooling down.

Please wait.

Blinking

In Red

(discre-

tionary)

(discre-

tionary)

The projector is cooling down. A certain error

has been detected.

Please wait until POWER indicator nishes blinking,

and then perform the proper measure using the item

descriptions below.

Blinking

In Red

Lighting

In Red

Lighting

In Red

Turned

off

The lamp does not light, and there is a possibility

that interior portion has become heated.

Please turn the power off, and allow the projector to

cool down at least 20 minutes. After the projector has

sufciently cooled down, please make conrmation of

the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

• Is the air lter dirty?

• Does the peripheral temperature exceed 35°C?

If the same indication is displayed after the remedy,

please change the lamp referring to the section

Replacing the lamp.

Blinking

In Red

Lighting

In Red

Blinking

In Red

Turned

off

The lamp cover has not been properly xed.

Please turn the power off, and allow the projector to

cool down at least 45 minutes. After the projector has

sufciently cooled down, please make conrmation of

the attachment state of the lamp cover. After performing

any needed maintenance, turn the power on again.

If the same indication is displayed after the remedy,

please contact your dealer or service company.

(continued on next page)

Troubleshooting

Regarding the indicator lamps (continued)

POWER

indicator

LAMP

indicator

TEMP

indicator

Description

Blinking

In Red

Lighting

In Red

Turned

off

Blinking

In Red

The cooling fan is not operating.

Please turn the power off, and allow the projector to

cool down at least 20 minutes. After the projector has

sufciently cooled down, please make conrmation

that no foreign matter has become caught in the fan,

etc., and then turn the power on again.

If the same indication is displayed after the remedy,

please contact your dealer or service company.

Blinking

In Red

Lighting

In Red

Turned

off

Lighting

In Red

There is a possibility that the interior portion

has become heated.

Please turn the power off, and allow the projector to

cool down at least 20 minutes. After the projector has

sufciently cooled down, please make conrmation of

the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

• Is the air lter dirty?

• Does the peripheral temperature exceed 35°C?

• If the projector is used at an altitude of about 1600 m

(5250 feet) or higher, set ALTITUDE of the SERVICE

item in the OPTION menu to HIGH (



57). If the

projector is used with a wrong setting, it may cause

damage to the projector itself or the parts inside.

Lighting

In Green

Simultaneous

blinking in Red

It is time to clean the air lter.

Please immediately turn the power off, and clean or

change the air lter referring to the section Cleaning

and replacing the air lter. After cleaning or changing

the air lter, please be sure to reset the lter timer.

After the remedy, reset the power to ON.

Lighting

In Green

Alternative

blinking in Red

There is a possibility that the interior portion

has become overcooled.

Please use the unit within the usage temperature

parameters (5°C to 35°C).

After the treatment, reset the power to ON.

(continued on next page)

Troubleshooting

Regarding the indicator lamps (continued)

• When the interior portion has become overheated, for safety

purposes, the projector is automatically shut down, and the indicator lamps

may also be turned off. In such a case, disconnect the power cord, and wait at

least 45 minutes. After the projector has sufciently cooled down, please make

conrmation of the attachment state of the lamp and lamp cover, and then turn

the power on again.

If the projector is used at an altitude of about 1600 m (5250 feet)

or higher, set ALTITUDE of the SERVICE item in the OPTION menu to HIGH (



57).

Otherwise, set it to NORMAL.

NOTE

Troubleshooting

Resetting all settings

When it is hard to correct some wrong settings, the FACTORY RESET function of

SERVICE item in OPTION menu (

59) can reset all settings (except LANGUAGE,

FILTER TIME, LAMP TIME, FILTER MESSAGE and SECURITY settings and etc.)

to the factory default. Be sure to set ALTITUDE after resetting all the settings (67).

Phenomena that may be easy to be mistaken for machine defects

About the phenomenon confused with a machine defect, check and cope with it

according to the following table.

Phenomenon Cases not involving a machine defect

Reference

page

Power does

not come on.

The electrical power cord is not plugged in.

Correctly connect the power cord.

The main power source has been interrupted during

operation such as by a power outage (blackout), etc.

Please disconnect the power plug from the power outlet,

and allow the projector to cool down at least 10 minutes,

then turn the power on again.

Either there is no lamp and/or lamp cover, or either

of these has not been properly xed.

Please turn the power off and disconnect the power

plug from the power outlet, and allow the projector to

cool down at least 45 minutes. After the projector has

sufciently cooled down, please make conrmation of

the attachment state of the lamp and lamp cover, and

then turn the power on again.

Neither sounds

nor pictures are

outputted.

The signal cables are not correctly connected.

Correctly connect the connection cables.

12, 13

Signal source does not correctly work.

Correctly set up the signal source device by referring to

the manual of the source device.

–

The input changeover settings are mismatched.

Select the input signal, and correct the settings.

21, 22

The BLANK function for pictures and the MUTE

function for sounds are working.

AV MUTE may be active.

Refer to the item “Sound does not come out” and “No

pictures are displayed” on the next page to turn off the

MUTE and BLANK functions.

20, 28

(continued on next page)

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

Phenomenon Cases not involving a machine defect

Reference

page

Sound does

not come out.

The signal cables are not correctly connected.

Correctly connect the audio cables.

12, 13

The MUTE function is working.

Restore the sound pressing MUTE or VOLUME +/-

button on the remote control.

The volume is adjusted to an extremely low level.

Adjust the volume to a higher level using the menu

function or the remote control.

20, 46

The AUDIO SOURCE/SPEAKER setting is not correct.

Correctly set the AUDIO SOURCE/SPEAKER in AUDIO menu.

No pictures are

displayed.

The signal cables are not correctly connected.

Correctly connect the connection cables.

12, 13

The brightness is adjusted to an extremely low level.

Adjust BRIGHTNESS to a higher level using the menu function.

The computer cannot detect the projector as a Plug-

and-Play monitor.

Make sure that the computer can detect a Plug-and-Play

monitor using another Plug-and-Play monitor.

The BLANK screen is displayed.

Press BLANK button on the remote control.

(continued on next page)

Phenomenon Cases not involving a machine defect

Reference

page

Video screen

display

freezes.

The FREEZE function is working.

Press FREEZE button to restore the screen to normal.

Colors have a

faded- out

appearance, or

Color tone is

poor.

Color settings are not correctly adjusted.

Perform picture adjustments by changing the COLOR

TEMP, COLOR, TINT and/or COLOR SPACE settings,

using the menu functions.

34, 39

COLOR SPACE setting is not suitable.

Change the COLOR SPACE setting to AUTO, RGB,

SMPTE240, REC709 or REC601.

Pictures

appear dark.

The brightness and/or contrast are adjusted to an

extremely low level.

Adjust BRIGHTNESS and/or CONTRAST settings to a

higher level using the menu function.

The projector is operating in Eco mode.

Set ECO MODE to NORMAL, and set AUTO ECO

MODE to OFF, in the SETUP menu.

43, 44

The lamp is approaching the end of its product

lifetime.

Replace the lamp.

65, 66

Pictures

appear blurry.

Either the focus and/or horizontal phase settings are

not properly adjusted.

Adjust the focus using the focus ring, and/or H PHASE

using the menu function.

24, 38

The lens is dirty or misty.

Clean the lens referring to the section Caring for the

lens.

(continued on next page)

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

Phenomenon Cases not involving a machine defect

Reference

page

Some kind

of image

degradation

such as

ickering or

stripes appear

on screen.

When the projector is operating in Eco mode,

ickering may appear on screen.

Set ECO MODE to NORMAL, and set AUTO ECO

MODE to OFF, in the SETUP menu.

43, 44

The OVER SCAN ratio is too big.

Adjust OVER SCAN in the IMAGE menu smaller.

Excessive VIDEO NR.

Change the setting of VIDEO NR in the INPUT menu.

The FRAME LOCK function cannot work on the

current input signal.

Set FRAME LOCK in the INPUT menu to OFF.

RS-232C does

not work.

The SAVING function is working.

Select NORMAL for STANDBY MODE item in the SETUP

menu.

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

• Although bright spots or dark spots may appear on the screen, this

is a unique characteristic of liquid crystal displays, and it does not constitute or

imply a machine defect.

NOTE

Specications

Specications

Please see the Specications in the User’s Manual (concise) which is a book.

End User License Agreement for the Projector Software

• Software in the projector consists of the plural number of independent software

modules and there exist our copyright or/and third party copyrights for each of

such software modules.

• Be sure to read “End User License Agreement for the Projector Software” which

is separated document.

Hitachi CP-EX250 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info