661481
8
Verklein
Vergroot
Pagina terug
1/136
Pagina verder
8
English
2. Replacing the blade
For your continued safety, blade inspection and
replacement on this tool should ONLY be performed by
a HITACHI AUTHORIZED SERVICE CENTER.
3. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
4. Replacing supply cord
If the replacement of the supply cord is necessary, it has
to be done by Hitachi Authorized Service Center to avoid
a safety hazard.
5. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
6. Cleaning on the outside
When the hedge trimmer is stained, wipe with a soft dry
cloth or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, for they melt
plastics.
7. Transport of the tool
Attach the blade case to the blade before carrying this
tool.
If you carry it without the blade case, the blade may
come in contact with your body, causing injury.
8. Storage
Store the hedge trimmer in a place out of reach of
children.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your
dealer or the Hitachi Authorized Service Center.
Symptom Possible cause Remedy
Does not operate. The power plug is not plugged into the
power socket.
Plug the power cord into the power
socket.
Foreign matter is lodged in the blade. When there is foreign matter in the blade,
disconnect the plug from receptacle
and use a pair of tongs or similar tool to
remove it.
Take great care since the tool may start
operating when the foreign matter has
been removed.
Sap or rust may also prevent the blade
from operating. Use a wire brush or similar
tool to remove sap or rust.
The tool does not trim well. The blade has become dull. Use a brush or cloth to remove sap.
If cleaning the blade does not improve
its cutting ability, contact the HITACHI
AUTHORIZED SERVICE CENTER to
have the blade replaced.
The blade stopped because it was used
to cut a branch whose width exceeded the
blade’s cutting capacity.
NOTE
Work that will repeatedly cause the
blade to stop will eventually damage
the motor.
Some garden trees have wood that is very
hard and may be beyond the capacity of
the tool even if it is of a width that is within
normal capacity. Use a pair of pruning
shear to remove thick branches before
starting work.
An oblique cut may also exceed the
capacity of the tool since the length of
the cut increases. Be sure to trim thick
branches at right angles.
0000Book_CH45Y.indb 80000Book_CH45Y.indb 8 2017/03/15 9:52:332017/03/15 9:52:33
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CH65Y bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CH65Y in de taal/talen: Alle talen als bijlage per email.

De handleiding is 8,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info