563866
9
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
9
English
until the cutting attachment stops. You have reached the correct idle
speed when the engine runs smoothly in all positions well below the
rpm when the cutting attachment starts to rotate.
If the cutting attachment still rotates after idle speed adjustment,
contact Hitachi Authorized Service Centers.
NOTE
Standard Idle rpm is 3000 min
-1
.
WARNING
When the engine is idling the cutting attachment must under no
circumstances rotate.
Air lter (Fig. 18)
The air lter must be cleaned from dust and dirt in order to avoid:
Carburetor malfunctions
Starting problems
Engine power reduction
Unnecessary wear on the engine parts
Abnormal fuel consumption
Clean the air lter daily or more often if working in exceptionally
dusty areas.
Cleaning the air lter
Remove the air lter cover and the lter (19). Rinse it in warm soap
suds. Check that the lter is dry before reassembly. An air lter
that has been used for some time cannot be cleaned completely.
Therefore, it must regularly be replaced with a new one. A damaged
lter must always be replaced.
Fuel lter (Fig. 19)
Drain all fuel from fuel tank and pull fuel lter line from tank. Pull lter
element out of holder assembly and rinse element in warm water with
detergent.
Rinse thoroughly until all traces of detergent are eliminated. Squeeze,
do not wring, away excess water and allow element to air dry.
NOTE
If element is hard due to excessive dirt build-up, replace it.
Spark plug (Fig. 20)
The spark plug condition is in uenced by:
An incorrect carburetor setting
Wrong fuel mixture (too much oil in the gasoline)
A dirty air lter
Hard running conditions (such as cold weather)
These factors cause deposits on the spark plug electrodes, which
may result in malfunction and starting di culties. If the engine is
low on power, di cult to start or runs poorly at idling speed, always
check the spark plug rst. If the spark plug is dirty, clean it and check
the electrode gap. Re-adjust if necessary. The correct gap is 0.6
mm. The spark plug should be replaced after about 100 operation
hours or earlier if the electrodes are badly eroded.
NOTE
In some areas, local law requires using a resistor spark plug
to suppress ignition signals. If this machine was originally
equipped with resistor spark plug, use same type of spark plug
for replacement.
Cutting blade (Fig. 21, 22)
The blades are installed to the blade guide with three to ve bolts
depending on blade length. Those bolts are tightened with a
clearance so that the blades can move smoothly.
When clearance is too small
The blades do not move properly and the sliding surfaces may seize.
When clearance is too large
The blades are poor in sharpness.
To adjust the blade clearance
1. Loosen the blade xing nuts.
2. Fully tighten the blade xing bolts and then loosen them approx.
1/2 turn.
3. With the bolts set at that position, tighten the blade xing nuts.
Be sure to replace blade guide xing bolts when they are loosened,
worn or damaged. Also be sure to replace damaged cutter blade.
NOTE
Properly lubricate the blade sliding surfaces with machine oil.
Gear case (Fig. 23)
Apply good quality lithium based grease through the grease ttings.
On some models, one of the grease ttings has been moved from
upper location to the bottom.
NOTE
Lubrication should be applied about 5 g at 20 hour intervals and
more frequently with heavy use.
Maintenance schedule
Below you will nd some general maintenance instructions. For
further information please contact Hitachi Authorized Service
Centers.
Daily maintenance
Check to ascertain that the fuel is not leaking.
Clean the exterior of the unit.
Check the blade guard for damage or cracks.
Change the guard in case of impacts or cracks.
Check that the blade is sharp, and without cracks.
Check that the blade nut is su ciently tightened.
Make sure that the blade transport guard is undamaged and that
it can be securely tted.
Check that nuts and screws are su ciently tightened.
Weekly maintenance
Check the starter, especially the cord and return spring.
Clean the exterior of the spark plug.
Remove the spark plug and check the electrode gap. Adjust it to
0.6 mm or change the spark plug.
Check that the air intake at the starter is not clogged.
Check that the angle gear is lled with grease.
Clean the air lter.
Monthly maintenance
Rinse the fuel tank with gasoline, and clean fuel lter.
Clean the exterior of the carburetor and the space around it.
Quarterly maintenance
Clean the cooling ns on the cylinder.
Clean the fan and the space around it.
Clean the mu er of carbon.
CAUTION
Cleaning of cylinder ns, fan and mu er shall be done by a
Hitachi Authorized Service Center.
000Book_CH27EPAP(S)_WE.indb 9000Book_CH27EPAP(S)_WE.indb 9 2012/09/27 14:26:472012/09/27 14:26:47
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CH27EPAP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CH27EPAP in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info