563769
11
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
11
English
NOTE
If engine does not start, repeat procedures from 2 to 4.
5. After starting engine, then allow the engine about 23 minutes
to warm up before subjecting it to any load.
Cutting (Fig. 19, 20, 21)
When cutting, operate engine at over 6500 rpm. Extended time
of use at low rpm may wear out the clutch prematurely.
Cut grass from right to left.
Blade thrust may occur when the spinning blade contacts a
solid object in the critical area.
A dangerous reaction may occur causing the entire unit and
operator to be thrust violently. This reaction is called blade
thrust. As a result, the operator may lose control of the unit
which may cause serious or fatal injury. Blade thrust is more
likely to occur in areas where it is di cult to see the material to
be cut.
Wear the harness as shown in the gure (if so equipped). The
blade turns counter-clockwise, therefore, be advised to operate
the unit from right to left for e cient cutting. Keep onlookers out
of working area at least 15 m.
NOTE
Press the quick release button or pull emergency release ap
(If so equipped) in the event of emergency.
WARNING
If cutting attachment should strike against stones or other
debris, stop the engine and make sure that the attachment and
related parts are undamaged. When grass or vines wrap around
attachment, stop engine and attachment and remove them.
Stopping (Fig. 22)
Decrease engine speed and run at an idle for a few minutes, then
turn o ignition switch.
WARNING
A cutting attachment can injure while it continues to spin after
the engine is stopped or power control is released. When the
unit is turned o , make sure the cutting attachment has stopped
before the unit is set down.
Semi-auto cutting head
6. Adjusting line length
Set the engine speed as low as possible and tap the head on
the ground. The nylon line will be drawn out about 3 cm with
each tap. (Fig. 23)
Also, you can extend the nylon line by hand but the engine must
be completely stopped. (Fig. 24)
Adjust the nylon line to the proper length of 1114 cm before
each operation.
MAINTENANCE
MAINTENANCE, REPLACEMENT OR REPAIR OF THE EMISSION
CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED
BY ANY NON-ROAD ENGINE REPAIR ESTABLISHMENT OR
INDIVIDUAL.
Carburetor adjustment (Fig. 25)
WARNING
The cutting attachment may be spinning during carburetor
adjustments.
Never start the engine without the complete fan case and tube
assembled! Otherwise the clutch can come loose and cause
personal injuries.
In the carburetor, fuel is mixed with air. When the engine is test
run at the factory, the carburetor is basically adjusted. A further
adjustment may be required, according to climate and altitude. The
carburetor has one adjustment possibility:
T = Idle speed adjustment screw.
Idle speed adjustment (T)
Check that the air lter is clean. When the idle speed is correct, the
cutting attachment will not rotate. If adjustment is required, close
(clockwise) the T-screw, with the engine running, until the cutting
attachment starts to rotate. Open (counter-clockwise) the screw
until the cutting attachment stops. You have reached the correct idle
speed when the engine runs smoothly in all positions well below the
rpm when the cutting attachment starts to rotate.
If the cutting attachment still rotates after idle speed adjustment,
contact your Hitachi dealer.
NOTE
Standard Idle rpm is 3000 rpm.
Some models sold areas with strict exhaust emission regulation
do not have high and low speed carburetor adjustments. Such
adjustments may allow the engine to be operated outside of
their emission compliance limits. For these models, the only
carburetor adjustment is idle speed.
WARNING
When the engine is idling the cutting attachment must under no
circumstances rotate.
Changing the engine oil
Dirty engine oil will considerably reduce the service life of the
engine. Check and change the engine oil regularly.
CAUTION
To avoid the risk of burn injuries, allow the engine to cool
thoroughly before changing the engine oil.
To prevent breakdown, ensure that no sand or dirt gets into the
tank while refueling.
When to change the oil: When rst using the unit, after
approximately 10 hours of operation or after 1 month, whichever
occurs earlier; subsequently, after every 50 hours of operation or
every 6 months, whichever occurs earlier.
Speci ed engine oil: Multigrade oil of classi cation SAE 10W-30
Engine oil capacity: 80 ml
1. Turn o the ignition switch.
2. Check that the fuel cap is securely tightened.
3. Remove the oil cap, tilt the unit so that the oil tank opening is on
the underside and drain the engine oil into a container. (Fig. 26)
4. When all the engine oil has been drained, place the unit
horizontally on a clean, at surface.
5. Fill the oil tank with engine oil up to the mouth of the oil tank
opening. (Fig. 15)
6. Tighten the oil cap securely by hand.
NOTE
Do not dispose of waste engine oil with garbage or into the
ground.
Dispose of the oil according to the speci ed method in your
area.
If you are unsure, contact the retailer where the oil was
purchased.
Fill the oil tank with the speci ed amount of engine oil.
Too much or too little engine oil may result in engine
breakdown.
Engine oil deteriorates naturally even if unused.
Change the engine oil regularly.
Air lter (Fig. 27)
The air lter must be cleaned from dust and dirt in order to avoid:
Carburetor malfunctions
Starting problems
Engine power reduction
Unnecessary wear on the engine parts
Abnormal fuel consumption
Clean the air lter daily or more often if working in exceptionally
dusty areas.
000Book_CG25EUS_WE.indb 11000Book_CG25EUS_WE.indb 11 2009/12/25 21:39:082009/12/25 21:39:08
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CG25EUS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CG25EUS in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 8,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info