563832
17
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
English
16
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem,
consult your dealer or the Hitachi Authorized Service Center.
Charger
Tool
The Charge lamp does not
go on.
The Charge lamp does not
go off after 4 hours of
charging.
Does not operate.
The power plug is not connected to
an AC outlet.
The battery is not properly
connected to the charger.
The battery or charger electrodes
are soiled.
The battery is extremely hot.
The battery or charger is faulty.
The battery is depleted. (The
battery level warning lamp does
not go on.)
The battery has not been properly
installed.
The blade has been incorrectly
installed.
Foreign matter is lodged in the
blade.
The tool has been used for heavy
work.
The Lock Off button was not
pressed when the switch was
pulled back.
Connect the power plug to an AC
outlet.
Insert the battery so that it is
properly seated in the charger.
Use a cotton swab or other tool to
clean the electrodes.
Allow the battery to properly cool
before charging.
Disconnect the power plug and
consult your dealer or the Hitachi
Authorized Service Center.
When a storage battery with little
power left is not used for an
extended period of time, battery
power may drop so low that it
cannot turn on the battery level
warning lamp. Charge the battery.
Remove the storage battery from the
battery compartment in the tool and
check for foreign matter. Also check
the battery electrodes for soiling.
Make sure that the battery is pressed
in until it clicks into place.
If the blade does not move but the
motor is turning, the blade has
probably been incorrectly installed.
Make sure that the crank holder and
crank cam has been installed.
When there is foreign matter in the
blade, remove the battery and use
a pair of tongs or similar tool to
remove it.
Take great care since the tool may
start operating when the foreign
matter has been removed.
Sap or rust may also prevent the
blade from operating. Use a wire
brush or similar tool to remove sap
or rust.
This is the effect of a function that
protects the battery by turning off
the motor when the tool is exposed
to an excessive load. Release the
switch and remove what caused
the excessive load and pull back
the switch to resume work.
To prevent accidents from
incorrect operation, the Lock Off
switch must be pressed while the
switch is pulled back to start the
motor.
Symptom Possible cause Remedy
01Eng_CH10DL_WE 9/30/09, 16:0216
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CG10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CG10 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 1,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info