506042
9
Verklein
Vergroot
Pagina terug
1/46
Pagina verder
8
English
(3) Firmly tighten the 6 mm knob bolt so secure the
turntable. On the side opposite of the angle calibration
markings on the turntable, there are the incline
calibration markings on the turntable, there are the
incline calibration markings. For example, when the
3/10 incline marking is aligned with the triangle mark
at the base, the b/a of the part of the material to be
cut will be 3/10 as shown in Fig. 5.
CAUTION
Never remove the 6 mm knob bolt; use of the tool
without it would be hazardous.
To prevent an accident or personal injury always firmly
tighten the 6 mm knob bolt.
NOTE
Positive stops are provided at the right and left of the
0° center setting, at 22.5°, 45° right and left settings.
Check that the miter angle scale and the tip of the
̅” mark are properly aligned.
Operation of the power tool with the angle calibration
marking and “̅” mark out of alignment, or with the
6 mm knob bolt not properly tightened, will result in
poor cutting precision.
9. Bevel cutting procedure (Fig. 2)
(1) Loosen the tension lever and bevel the saw blade to
the left.
(2) Adjust the bevel angle to the desired setting while
watching the bevel angle scale and indicator, then
secure the tension lever.
(3) Perform cutting as described in 7.
WARNING
When the workpiece is secured on the left side of the
blade, the short cut-off portion will come to rest on
the right side of the saw blade. Always turn the power
off and let the saw blade stop completely before
raising the handle from the workpiece.
If the handle is raised while the saw blade is still
rotating, the cut-off piece may become jammed
against the saw blade causing fragments to scatter
about dangerously.
10. Compound cutting procedure
Compound cutting can be performed by following the
instructions in 8 and 9 above. At a bevel of 45° and a
miter angle of 45°.
WARNING
Always secure the workpiece with the right hand side
for compound cutting.
Never rotate the turntable to the right for compound
cutting, because the saw blade might then contact the
clamp or vise that secures the workpiece, and cause
personal injury or damage.
11. Cutting long materials (Holder is optional accessory)
When cutting long materials, use an auxiliary platform
which is the same height as the holder and base of
the special auxiliary equipment. Insert the holder in
the hole on the left side of the base and secure. (Fig.
6)
Adjust the holder upon inserting so that it is the same
height as the base. (Fig. 7)
After adjusting the height of the holder use the
securing 6mm knob bolt to secure the holder.
CAUTION
When transporting or carrying the tool, do not grasp
the holder.
There is the danger of the holder slipping out of the
base. Grasp the handle instead of the holder.
MOUNTING AND DISMOUNTING SAW BLADE
WARNING
To prevent an accident or personal injury, always turn
off the trigger switch and disconnect the power plug
from the receptacle before removing or installing a
blade.
1. Mounting the saw blade (Fig. 8 and Fig. 9)
(1) Press in spindle lock and loosen bolt with 10mm box
wrench. Since the bolt is left-hand threaded, loosen
by turning it to the right.
NOTE
If the spindle lock cannot be easily pressed in to lock
the saw blade spindle, turn the bolt with 10mm box
wrench while applying pressure on the spindle lock.
The saw blade spindle is locked when the spindle lock
is pressed inward.
(2) Remove the bolt and washer (C) and collar (A) or collar
(B).
(3) Before mounting saw blade, carefully clean and
reinstall the collar (A) or collar (B). The collar (A) has
an outside diameter of 30mm as shown in Fig.9.
The collar (B) has an outside diameter of 25.4 mm as
shown in Fig. 9.
(4) Lift the safety cover and mount the saw blade.
WARNING
When mounting the saw blade, confirm that the
rotation indicator mark on the saw blade and the
rotation direction of the saw cover are properly
matched.
(5) Thoroughly clean washer (C), collar (A) or collar (B)
and the bolt, and install them onto the saw blade
spindle.
(6) Press in the spindle lock and tighten the bolt by turning
it to the left by 10mm box wrench as in Fig. 3 and Fig.
8.
CAUTION
Confirm that the spindle lock has returned to the
retract position after installing or removing the saw
blade.
Tighten the bolt so it does not come loose during
operation.
Confirm that the bolt has been properly tightened
before the power tool is started.
Confirm that the safety cover has closed position.
2. Dismounting the saw blade
Dismount the saw blade by reversing the mounting
procedures described in paragraph 1 above.
The saw blade can easily be removed after lifting the
safety cover.
CAUTION
Never attempt to install saw blade larger than 216mm
in diameter. Always install saw blades that are 216mm
in diameter or less.
MAINTENANCE AND INSPECTION
WARNING
To avoid an accident or personal injury, always
confirm the trigger switch is turned OFF and that the
power plug has been disconnected from the
receptacle before performing any maintenance or
inspection of this tool.
C8FC/1-E,65E 6.24.2002, 9:43 AM8
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi C8FC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi C8FC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info