662595

Hikvision DS-KV8202 Handleiding

5
Verklein
Vergroot
Pagina terug
1/87
Pagina verder
UD02940B
Video Intercom Door Station
(V Series)
User Manual
Video Intercom Door Station·User Manual
i
User Manual
© 2016 Hangzhou Hikvision Digital Technology Co., Ltd.
This user manual is intended for users of the models below:
Series
Model
Door Station (V Series)
DS-KV8102-IM
DS-KV8202-IM
DS-KV8402-IM
DS-KV8102-IP
DS-KV8102-VP
It includes instructions on how to use the Product. The software embodied in the
Product is governed by the user license agreement covering that product.
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou
Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This
manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by
any means, without the prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are
registered trademarks or the subject of applications for the same by Hikvision and/or its
affiliates. Other trademarks mentioned in this manual are the properties of their
respective owners. No right of license is given to use such trademarks without express
permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL.
HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION
CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE
WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
Video Intercom Door Station·User Manual
ii
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA
OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN
DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
Support
Should you have any questions, please do not hesitate to contact your local dealer.
0104001060823
Video Intercom Door Station·User Manual
iii
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm
between the radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the R&TTE Directive
1999/5/EC, the EMC Directive 2004/108/EC, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info
Video Intercom Door Station·User Manual
iv
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection point.
For more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.)
is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et
son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse
pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Video Intercom Door Station·User Manual
v
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Please use the power adapter, which is provided by normal company. The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the device yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
Cautions
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or
places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specification of the device for
the detailed operating temperature), cold, dusty or damp locations, and do not
expose it to high electromagnetic radiation.
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.
Video Intercom Door Station·User Manual
vi
The device cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as
heater or radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may
occur otherwise (which is not a malfunction however), and affecting the endurance of
sensor at the same time.
Please use the provided glove when open up the device cover, avoid direct contact
with the device cover, because the acidic sweat of the fingers may erode the surface
coating of the device cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the device
cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device and
lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries according to
the instructions provided by the battery manufacturer.
Video Intercom Door Station·User Manual
vii
Table of Contents
1 Overview ...................................................................................................... 1
1.1 Introduction ............................................................................................................. 1
1.2 Main Features .......................................................................................................... 1
2 Appearance .................................................................................................. 2
2.1 Appearance of DS-KV8X02-IM ................................................................................. 2
2.2 Appearance of DS-KV8102-XP.................................................................................. 3
3 Typical Application ....................................................................................... 5
3.1 Typical Application of DS-KV8X02-IM ...................................................................... 5
3.2 Typical Application of DS-KV8102-XP ....................................................................... 6
4 Terminals and Interfaces .............................................................................. 7
5 Installation and Wiring ................................................................................. 8
5.1 Installation of DS-KV8X02-IM................................................................................... 8
5.1.1 Gang Box for DS-KV8X02-IM ............................................................................. 8
5.1.2 Wall Mounting with Gang Box of DS-KV8X02-IM .............................................. 9
5.2 Installation of DS-KV8102-XP ................................................................................. 10
5.2.1 Installation Plate for DS-KV8102-XP ................................................................ 10
5.2.2 Wall Mounting with Gang Box of DS-KV8102-XP............................................. 11
5.3 Wiring Description ................................................................................................. 13
5.3.1 Door Lock Wiring ............................................................................................ 13
5.3.2 Door Magnetic Wiring ..................................................................................... 14
5.3.3 Exit Button Wiring ........................................................................................... 14
5.3.4 Alarm Device Input Wiring .............................................................................. 15
6 Before You Start ......................................................................................... 16
7 Remote Operation via Batch Configuration Tool ......................................... 17
7.1 Activating Device Remotely ....................................................................................17
7.2 Editing Network Parameters .................................................................................. 18
7.3 Adding Device ........................................................................................................ 19
7.3.1 Adding Online Device ...................................................................................... 19
7.3.2 Adding by IP Address ....................................................................................... 20
7.3.3 Adding by IP Segment ..................................................................................... 21
7.4 Configuring Devices Remotely ............................................................................... 22
7.4.1 System ............................................................................................................. 22
7.4.2 Video Intercom ................................................................................................ 27
7.4.3 Network .......................................................................................................... 31
7.4.4 Video Display .................................................................................................. 33
7.5 Video Intercom Device Set-up Tool ....................................................................... 34
7.5.1 Setting a Community Structure ....................................................................... 35
7.5.2 Setting Main/Sub Door Station ....................................................................... 35
Video Intercom Door Station·User Manual
viii
7.6 Batch Upgrading .................................................................................................... 38
7.6.1 Adding Devices for Upgrading ......................................................................... 38
7.6.2 Upgrading Devices ........................................................................................... 40
8 Remote Operation via iVMS-4200 .............................................................. 42
8.1 System Configuration ............................................................................................. 42
8.2 Device Management .............................................................................................. 43
8.2.1 Adding Video Intercom Devices ...................................................................... 43
8.2.2 Modifying Network Information ..................................................................... 46
8.2.3 Resetting Password ......................................................................................... 46
8.3 Configuring Devices Remotely via iVMS-4200 ....................................................... 48
8.4 Picture Storage ...................................................................................................... 48
8.4.1 Adding Storage Server ..................................................................................... 49
8.4.2 Formatting the HDDs ....................................................................................... 50
8.4.3 Configuring Storage Server Picture Storage .................................................... 50
8.5 Video Intercom Configuration ................................................................................52
8.5.1 Group Management ........................................................................................ 53
8.5.2 Video Intercom ............................................................................................... 58
8.5.3 Card Management .......................................................................................... 60
8.5.4 Notice Management ....................................................................................... 69
8.6 Device Arming Control ........................................................................................... 71
9 Local Operation .......................................................................................... 73
9.1 Calling Resident ..................................................................................................... 73
9.1.1 Calling Resident (DS-KV8X02-IM) .................................................................... 73
9.1.2 Calling Resident (DS-KV8102-XP) ...................................................................... 74
9.2 Issuing Card ........................................................................................................... 75
9.3 Unlocking Door .......................................................................................................76
Appendix ...................................................................................................... 77
Installation Notice ....................................................................................................... 77
Wiring Cables .............................................................................................................. 77
Video Intercom Door Station·User Manual
1
1 Overview
1.1 Introduction
The door station (V series) can realize functions such as video intercom, access control,
one-card system, zone alarm, and visitor messages to form a complete smart community
video intercom solution.
The door station (V series) is mainly applied in the villa, and can works as door station,
outer door station, and doorphone.
1.2 Main Features
Video intercom function
HD video surveillance (Max. resolution 1280×720@25fps, WDR, 120° wide angle)
Self-adaptive light supplement
Access control function
Activating card via local station function (This function will be invalid if the card has
been activated via iVMS-4200)
Auto-uploading captured pictures to FTP or iVMS-4200 Client while unlocking the
door
Door magnetic alarm and tamper alarm function
Noise suppression and echo cancellation
Remote upgrade, batch setting functions
Video Intercom Door Station·User Manual
2
2 Appearance
2.1 Appearance of DS-KV8X02-IM
For device DS-KV8X02-IM, the number of call buttons varies according to its model. Take
the figure of device DS-KV8402-IM as an example.
For device DS-KV8102-IM, there is only 1 call button.
For device DS-KV8202-IM, there are 2 call buttons.
For device DS-KV8402-IM, there are 4 call buttons.
Figure 2-1 Appearance of DS-KV8402-IM
Table 2-1 Description of DS-KV8X02-IM
Models
Description
DS-KV8102-IM
DS-KV8202-IM
DS-KV8402-IM
Low Illumination Supplement
Light
Built-in Camera
Card Induction Area
Call Button
Loudspeaker
Room No. (Customized)
Microphone
Tamper Button
Video Intercom Door Station·User Manual
3
You need not customize the Room No. for device DS-KV8102-IM.
Default settings of call button: when you press the call button, it calls the resident;
and when you hold down the call button, it calls the center.
You can change the calling mode of the call button via Batch Configuration Tool or
iVMS-4200 client software. See 7.4.2 Video Intercom for detail steps.
2.2 Appearance of DS-KV8102-XP
1
2
3
4
5
Figure 2-2 Appearance of DS-KV8102-XP
Table 2-2 Description of DS-KV8102-XP
Models
Description
DS-KV8102-IP
DS-KV8102-VP
Microphone
Low Illumination Supplement
Light
Built-in Camera
Card Induction Area
Call Button
Tamper Button
Loudspeaker
Video Intercom Door Station·User Manual
4
Default settings of call button: when you press the call button, it calls the resident;
and when you hold down the call button, it calls the center.
You can change the calling mode of the call button via Batch Configuration Tool or
iVMS-4200 client software. See 7.4.2 Video Intercom for detail steps.
Video Intercom Door Station·User Manual
5
3 Typical Application
3.1 Typical Application of DS-KV8X02-IM
Please refer to the following figure for typical application of DS-KV8102-IM/
DS-KV8202-IM/ DS-KV8402-IM door station.
Master Station
Switch
Client Software
Door Station
IPC
LAN
Card Reader
Network Cable
Optical Fiber
One Resident
RS-485
Wi-Fi
Resident 1
1F
2F
Resident 2
Resident 1Resident 2
Indoor
Extension 2
Indoor
Extension 2
House
App
Figure 3-1 Typical Application of DS-KV8X02-IM
Video Intercom Door Station·User Manual
6
3.2 Typical Application of DS-KV8102-XP
Please refer to the following figures for typical applications of DS-KV8102-IP/
DS-KV8102-VP door station.
Switch
Client Software
Network Cable
Optical Fiber
Door Station
Resident 1
IPC
Video/Audio
Distributor
LAN
Indoor
Extension 1
Indoor
Extension 2
Master Station
Card Reader
RS-485
App
Wi-Fi
House
Figure 3-2 Typical Application of DS-KV8102-XP
Video Intercom Door Station·User Manual
7
4 Terminals and Interfaces
Please refer to the following figure for terminals and interfaces of door station.
①-⑤
⑥-⑦
⑧-⑨
⑩-⑫
⑬
Figure 4-1 Terminals and Interfaces
Table 4-1 Descriptions of Terminals and Interfaces
Terminals and Interfaces
Name
No.
Color
Description
ALARM IN
1
YELLOW/BLUE
ALARM_1
2
YELLOW/ORANGE
ALARM_2
3
YELLOW/GREEN
ALARM_3
4
YELLOW/BROWN
ALARM_4
5
YELLOW/BLACK
ALARM_GND
Power Supply
6
RED
DC 12V Power Supply Input
GND
7
BLACK
Grounding
RS485
8
ORANGE
RS485+
9
YELLOW
RS485-
ALARM OUT
10
PINK
DR_NC
11
BLUE
DR_NO
12
BROWN
DR_COM
LAN
13
LAN
Network Interface
4 I/O Input terminals (ALARM_1~ALARM_4) can be set as door magnetic input or
door switch key input, and terminal ALARM_GND is for grounding connection.
1 I/O Output terminal can be enabled for controlling electric lock or disabled.
Video Intercom Door Station·User Manual
8
5 Installation and Wiring
5.1 Installation of DS-KV8X02-IM
To install the door station onto the wall, you are required to utilize a matched gang box.
5.1.1 Gang Box for DS-KV8X02-IM
Please refer to the following figures for the dimensions of gang box for DS-KV8102-IM/
DS-KV8202-IM/ DS-KV8402-IM door station.
89
168
49
54
97
50
45
100
73.92
Figure 5-1 Front View & Rear View (DS-KV8X02-IM)
The dimension of gang box for model DS-KV8102-IM/ DS-KV8202-IM/ DS-KV8402-IM
door station is: 89 (width) × 168 (length) ×38 (depth) mm.
Video Intercom Door Station·User Manual
9
The dimensions above are theoretical. The actual size can be slightly different from
the theoretical dimension.
5.1.2 Wall Mounting with Gang Box of DS-KV8X02-IM
Steps:
1. Take the gang box and screws from the packing box.
2. Chisel a hole in the wall for inserting the gang box. The size of the hole should be 90
(width) ×170 (length) × 38(depth) mm.
3. Insert the gang box into the hole and fix it with 4 PA4 screws, as shown in the figure
below.
PA4 Screws
Figure 5-2 Insert the Gang Box (DS-KV8X02-IM)
4. After fixing the gang box, install the door station into the gang box according to the
direction of the arrow, as shown in the figure below.
Figure 5-3 Insert the Door Station (DS-KV8X02-IM)
Video Intercom Door Station·User Manual
10
5. After inserting the door station into the gang box, pull the device downwards to hook
the door station with the gang box.
6. Secure the door station by inserting the fixing screw according to the direction of the
arrow of the figure below.
M4 Screw
Figure 5-4 Secure the Door Station (DS-KV8X02-IM)
5.2 Installation of DS-KV8102-XP
5.2.1 Installation Plate for DS-KV8102-XP
To install the DS-KV8102-XP model onto the wall, an installation plate and a gang box are
required.
20
69
18
41.48
9.3
72.7
Hollow Area
91.6
Figure 5-5 Dimensions of Installation Plate (DS-KV8102-XP)
Video Intercom Door Station·User Manual
11
The dimension of gang box for model DS-KV8102-IP/ DS-KV8102-VP door station is: 75
(width) × 75 (length) × 50 (depth) mm.
The dimensions above are theoretical. The actual size can be slightly different from
the theoretical dimension.
5.2.2 Wall Mounting with Gang Box of DS-KV8102-XP
Steps:
1. Take the gang box, installation plate and screws from the packing box.
2. Chisel a hole in the wall for inserting the gang box. The size of the hole should be 76
(width) × 76 (length) × 50 (depth) mm.
3. Insert the gang box into the hole, as shown in the figure below.
Figure 5-6 Insert the Gang Box (DS-KV8102-XP)
4. Attach the installation plate to the gang box and align the screw holes of the
installation plate with the screw holes of the gang box.
5. Insert 2 PA4 screws and a KA4 screw into the screw holes to fix the installation plate
onto the gang box. (The KA4 screw is optional.)
PA4 Screws
KA4 Screw
Figure 5-7 Attach the Installation Plate (DS-KV8102-XP)
Video Intercom Door Station·User Manual
12
6. After installing the installation plate, install the door station by inserting the rear
component into the hollow area of the installation plate.
While inserting the door station into the installation plate, incline the device by 5~10°,
as shown in the figure below.
Hollow Area
Rear Component
Figure 5-8 Install the Door Station (DS-KV8102-XP)
7. Secure the door station by inserting the fixing screw according to the direction of the
arrow of the figure below.
KM3 Screw
Figure 5-9 Secure the Door Station (DS-KV8102-XP)
Video Intercom Door Station·User Manual
13
5.3 Wiring Description
5.3.1 Door Lock Wiring
Figure 5-10 Door Lock Wiring
Terminal DR_NC/DR_COM is set as default for connecting magnetic lock/electric bolt;
terminal DR_NO/DR_COM is set as default for connecting electric strike.
To connect electric lock, it is required to set the output of terminal
DR_NC/DR_COM/DR_NO to be electric lock with Batch Configuration Tool or
iVMS-4200 client software.
Video Intercom Door Station·User Manual
14
5.3.2 Door Magnetic Wiring
Figure 5-11 Door Magnetic Wiring
To connect door magnetic, it is required to set the input of one alarm in terminal
(ALARM_1, ALARM_2, ALARM_3, or ALARM_4) to be door magnetic with Batch
Configuration Tool or iVMS-4200 client software.
5.3.3 Exit Button Wiring
Figure 5-12 Exit Button Wiring
Video Intercom Door Station·User Manual
15
To connect exit button, it is required to set the input of one alarm in terminal (ALARM_1,
ALARM_2, ALARM_3, or ALARM_4) to be exit button with Batch Configuration Tool or
iVMS-4200 client software.
5.3.4 Alarm Device Input Wiring
Figure 5-13 Alarm Device Input Wiring
To connect other alarm devices, it is required to set the input of one alarm in terminal
(ALARM_1, ALARM_2, ALARM_3, or ALARM_4) to be custom with Batch Configuration
Tool or iVMS-4200 client software.
Video Intercom Door Station·User Manual
16
6 Before You Start
For the first time use of the device, you are required to activate the device. You can
activate the device and set the device password via internet with Batch Configuration
Tool, or with iVMS-4200 client software, or with Video Intercom Set-up Tool.
To activate the device with Batch Configuration Tool or iVMS-4200, refer to 7
Remote Operation via Batch Configuration Tool and 8 Remote Operation via
iVMS-4200.
Please refer to 7.1 for creating the device password.
Video Intercom Door Station·User Manual
17
7 Remote Operation via Batch
Configuration Tool
7.1 Activating Device Remotely
Purpose:
You are required to activate the device first by setting a strong password for it before
you can use the device.
Activation via Batch Configuration Tool, and Activation via iVMS-4200 are supported.
Here take activation via Batch Configuration Tool as example to introduce the device
activation. Please refer to the user manual for the activation via iVMS-4200.
Steps:
1. Run the Batch Configuration Tool.
Figure 7-1 Selecting Inactive Device
2. Select an inactivated device and click the Activate button.
Figure 7-2 Activation
3. Create a password, and confirm the password.
Video Intercom Door Station·User Manual
18
STRONG PASSWORD RECOMMENDED– We highly recommend you create a
strong password of your own choosing (Using a minimum of 8
characters, including at least three of the following categories:
upper case letters, lower case letters, numbers, and special
characters.) in order to increase the security of your product. And we
recommend you reset your password regularly, especially in the high security
system, resetting the password monthly or weekly can better protect your
product.
4. Click the OK button to activate the device.
When the device is not activated, the basic operation and remote operation of device
cannot be performed.
You can hold the Ctrl or Shift key to select multiple devices in the online devices, and
click the Activate button to activate devices in batch.
7.2 Editing Network Parameters
Purpose:
To operate and configure the device via LAN (Local Area Network), you need connect the
device in the same subnet with you PC. You can edit network parameters via batch
configuration tool, and iVMS-4200 software. Here take editing network parameters via
batch configuration tool as example.
Steps:
1. Select an online activated device and click the Edit NET Parameters button.
Figure 7-3 Clicking Edit NET Parameters Button
2. Change the device IP address and gateway address to the same subnet with your
computer.
3. Enter the password and click the OK button to activate the network parameters
modification.
Video Intercom Door Station·User Manual
19
Figure 7-4 Editing Network Parameters
The default port No. is 8000.
After editing the network parameters of device, you should add the devices to the
device list again.
7.3 Adding Device
Before you start:
Make sure the device to be added has been activated.
Purpose:
For batch configuration tool software, you should add device to the software so as to
configure the device remotely.
The software provides 3 ways for adding the devices. You can add the active online
devices within your subnet, add devices by IP address, and add devices by IP segment.
7.3.1 Adding Online Device
Before you start:
Make sure the device to be added is in the same subnet with your computer. Otherwise,
please edit network parameters first.
Steps:
1. Select an active online device or hold the Ctrl or Shift key to select multiple devices in
the online devices list.
Figure 7-5 Online Devices Interface
Video Intercom Door Station·User Manual
20
2. Click the button to pop up the login dialog box.
Figure 7-6 Login Dialog Box
3. Enter the user name and password.
4. Click the OK button to save the settings.
Only devices successfully logged in will be added to the device list for configuration.
If you add devices in batch, please make sure selected devices have the same user
name and password.
7.3.2 Adding by IP Address
Purpose:
You can add the device by entering IP address.
Steps:
1. Click the button to pop up the adding devices dialog box.
Figure 7-7 Adding Button
2. Select IP Address in the adding mode drop-down list.
3. Enter the IP address, and set the port No., user name and password of the device.
Video Intercom Door Station·User Manual
21
Figure 7-8 Adding by IP Address
4. Click the OK button to add the device to the device list.
You cannot add the device(s) to the device list if the user name and password are not
identical.
When you add devices by IP Address, IP Segment or Port No., the devices should be
online devices.
7.3.3 Adding by IP Segment
Purpose:
You can add many devices at once whose IP addresses are among the IP segment.
Steps:
1. Click the button to pop up the adding devices dialog box.
Figure 7-9 Adding Button
2. Select IP Segment in the adding mode drop-down list.
3. Set the Start IP Address and End IP Address.
4. Enter port No., user name, and password.
Video Intercom Door Station·User Manual
22
Figure 7-10 Adding by IP Segment
5. Click the OK button to search and add the devices whose IP addresses are within the
range of the defined IP segment to the device list.
7.4 Configuring Devices Remotely
In the device list area, select a device and click or to enter
the remote configuration interface.
Figure 7-11 Remote Configuration
7.4.1 System
Click the System button on the remote configuration interface to display the device
information: Device Information, General, Time, System Maintenance, User, and RS485,
and so on.
Device Information
Click the Device Information button to enter device basic information interface. You can
view basic information (the device type, and serial No.), and version information of the
device.
Figure 7-12 Device Information
Video Intercom Door Station·User Manual
23
General
Click the General button to enter device general parameters settings interface. You can
view and edit the device name and device ID.
Figure 7-13 General
Time
Steps:
1. Click the Time button to enter the device time settings interface.
Figure 7-14 Time Settings
2. Select Time Zone or Enable NTP.
Time Zone
1) Select a time zone from the drop-down list menu.
2) Click the Synchronization button.
NTP
1) Check the checkbox of Enable NTP to enable NTP.
2) Enter the server address, NTP port, and synchronization interval.
DST
1) Check the checkbox of Enable DST to enable DST.
2) Enter the start time and end time of DST, and set the DST bias.
3. Click the Save button to save and realize the time settings.
Video Intercom Door Station·User Manual
24
The default port No. is 123.
System Maintenance
Purpose:
You can operate the system management and remote upgrading on the system
maintenance interface.
Steps:
1. Click the System Maintenance button to enter the system maintenance interface.
Figure 7-15 System Maintenance
2. Click Reboot and the system reboot dialog box pops up. Click Yes to reboot the
system.
3. Click Restore Default Settings to restore the default parameters.
4. Click Restore All to restore all parameters of device and reset the device to inactive
status.
5. Click Import Configuration File and the import file window pops up. Select the path
of remote configuration files. Click Open to import the remote configuration file. The
configuration file is imported and the device will reboot automatically.
Video Intercom Door Station·User Manual
25
Figure 7-16 Import File
6. Click Export Configuration File and the export file window pops up. Select the saving
path of remote configuration files and click Save to export the configuration file.
Figure 7-17 Export File
7. Click to select the upgrade file and click Upgrade to remote upgrade the device.
The process of remote upgrade will be displayed in the process bar.
Figure 7-18 Remote Upgrade
Video Intercom Door Station·User Manual
26
Click Restore Default Settings button, all default settings, excluding network
parameters, will be restored.
Click Restore All button, all default settings, including network parameters, will be
restored. The device will be reset to inactivated status.
User
Purpose:
You can edit the password for logging in the device.
Steps:
1. Click the User button to enter the user information editing interface.
Figure 7-19 Select User Name
2. Select the user to edit and click the Modify button to enter the user parameter
interface.
Figure 7-20 Modify User Information
3. Enter the new password, and confirm it.
4. Click the Save button to realize the editing of password.
The new password and confirm password should be identical.
Video Intercom Door Station·User Manual
27
After editing the password of device, click button from the device list, the added
device will not be there. You should add the device again with new password to
operate the remote configuration.
RS485
Click the RS485 button to enter the RS485 setting interface. You can view and edit the
RS485 parameters of the device.
Figure 7-21 RS-485
For door station (V series), there are 4 choices for the working mode: transparent
channel, card reader, disable, and custom.
7.4.2 Video Intercom
Click the Video Intercom button on the remote configuration interface to enter the
video intercom parameters settings: Device Number Configuration, Time Parameters,
Password, Zone Configuration, IP Camera Information, and Volume Input and Output
Configuration, and so on.
Device ID Configuration
Steps:
1. Click the ID Configuration button to enter device ID configuration interface.
Figure 7-22 ID Configuration (Villa Door Station and Doorphone)
Video Intercom Door Station·User Manual
28
2. Select the device type from the drop-down list, and set the corresponding
information.
3. Click the Save button to enable the device number configuration.
For main door station (D series or V series), the serial No. is 0.
For sub door station (D series or V series), the serial No. is higher than 0. Serial No.
ranges from 1 to 99.
For each villa or building, at least one main door station (D series or V series) should
be configured, and sub door stations (D series or V series) can be customized.
For one main door station (D series or V series), at most 8 sub door stations can be
customized.
Select doorphone as device type, and the serial No. is not necessary to configure.
Please utilize the doorphone along with the main door station (V Series or D Series).
V series door station cannot be used as outer door station.
Time Parameters
1. Click the Time Parameters button to enter time parameters settings interface.
2. Configure the maximum ring duration, maximum live view time, and call forwarding
time.
3. Click the Save button.
Figure 7-23 Time Parameters
For door station, maximum speaking time and maximum message time should be
configured. Maximum speaking time varies from 90s to 120s, and maximum message
time varies from 30s to 60s.
Access Control and Elevator
Step:
1. Click the Access Control and Elevator button to enter password changing interface.
Video Intercom Door Station·User Manual
29
Figure 7-24 Access Control and Elevator Configuration
2. Set corresponding parameters on the access control and elevator settings interface.
Access Control
1) Select the door No.
2) Set the door-unlocked duration.
3) (Optional) Enable the function of Delay Door Alarm.
4) Click the Save button to enable the settings.
Enabling Card Encrypt, the door station can recognize the encrypted information
of the card when you swiping the card on the door station.
Elevator Control
1) Select the elevator No., interface, RS485 protocol.
2) Select Yes/No of the elevator linkage.
3) Enter the server IP address and server port No..
3. Click the Save button to enable the settings.
This function only applies to door stations, except for the doorphone.
Video Intercom Door Station·User Manual
30
IO Input and Output
Step:
1. Click the I/O Input and Output button to enter the I/O input and output interface.
Figure 7-25 IO Input/Output Configuration
2. Select I/O input No., input mode, output No., and output mode.
3. Click the Save button to enable the settings.
For door station (V series), there are 4 I/O Input Terminals, corresponding to SENSOR
interfaces (S1, S2, S3, S4) of door station.
For door station (D series and V series), there are 4 I/O Output Terminals.
Terminal 1~2 correspond to DOOR interfaces (NO1/COM1/NC1; NO2/COM2/NC2) of
door station. You can enable/disable IO Out by selecting from the dropdown list.
Terminal 3~4 correspond to interfaces of ALARM OUT (AO1+, AO1-; AO2+, AO2-).
Volume Input and Output
Step:
1. Click Volume Input/Output button to enter the volume input and output interface.
Figure 7-26 Volume Configuration
2. Slide the slider to adjust the volume input and volume output.
3. Click the Save button to enable the settings.
Video Intercom Door Station·User Manual
31
Call Button
1. Click the Call Buttons button to enter the calling buttons settings interface.
Figure 7-27 Call Buttons Interface
2. Select the button number.
3. Enter the floor No. and the room No..
4. Click the Save button to enable the settings.
For DS-KV8102-IM, DS-KV8102-IP, and DS-KV8102-VP, there is no need setting the
Room No..
If enabling Quick Press for Calling Center, you should call resident by holding down
the call button, and call center by quickly pressing the call button.
7.4.3 Network
Local Network Configuration
Steps:
1. Click the Local Network Configuration button to enter local network configuration
interface.
Figure 7-28 Local Network Parameters
2. Enter the local IP address, subnet mask, gateway address, and port No..
3. Click the Save button to enable the settings.
The default port No. is 8000.
Video Intercom Door Station·User Manual
32
After editing the local network parameters of device, you should add the devices to
the device list again.
Linked Devices Network Configuration
Purpose:
In the linked devices network configuration interface, you can configure the network
parameters of master stations, SIP servers and management centers of the same LAN.
The devices can be linked to the door station and realize the linkage between these
devices.
Steps:
1. Click the Linked Network Configuration button to enter linked network configuration
interface.
Figure 7-29 Linked Network Configuration
2. Enter the master station IP address, (main) door station IP address, SIP server IP
address, management center IP address, and doorphone IP address.
3. Select the main door station type from the drop-down list.
4. Click the Save button to enable the settings.
After adding master station IP Address, the linkage between indoor station and
master station can be realized.
After adding the door station IP Address, the video intercom between indoor stations
of same building can be realized.
After adding SIP Server Address IP, the video intercom of same community: video
intercom between indoor stations of different building, calling indoor station from
outer door station and video intercom between management center and indoors.
After adding management center IP Address, the events can be uploaded to the
management center.
For indoor extension, only parameter about the main indoor station should be
configured.
FTP
Steps:
1. Click the FTP button to enter the FTP parameters interface.
Video Intercom Door Station·User Manual
33
Figure 7-30 FTP Configuration
2. Check the checkbox of Enable Main FTP.
3. Select IP address from the drop-down list of server mode.
4. Enter the FTP server address, and port No..
5. Check the checkbox to enable the anonymity (optional).
6. Enter the name and password.
7. Select the directory structure and set the separator, naming item, and naming
element.
8. Click the Save button to enable the FTP parameters settings.
The default port No. is 21.
To enable anonymity or not is according to whether the FTP server enables
anonymity.
After configuring the FTP parameters, the captured pictures of door station will be
uploaded to the FTP server automatically.
This function only applies to the door station, except for the doorphone.
7.4.4 Video Display
Steps:
1. Click the Video Display button to enter the video parameters interface.
Video Intercom Door Station·User Manual
34
Figure 7-31 Video Display
2. Select the camera No..
3. Select the video standard (PAL and NTSC can be selected).
4. Set the brightness, contrast, and saturation of the video.
5. Click the Save button to enable the settings.
Click the Restore Default Settings button to restore all parameters excluding network
parameters to the factory settings.
The live view of indoor station will be disabled.
7.5 Video Intercom Device Set-up Tool
Purpose:
You can assign the device to the community, activate and set the device, and configure
the network parameters and linked network parameters for the device by using the
video intercom device set-up tool.
In the device list area, click to enter the video intercom device set-up tool.
Video Intercom Door Station·User Manual
35
Figure 7-32 Video Device Set-up Tool
7.5.1 Setting a Community Structure
Set a community structure in the video intercom device set-up tool first, based on the
real community situation, and then assign devices to the community accordingly.
Figure 7-33 Setting a Community Structure
7.5.2 Setting Main/Sub Door Station
Setting Main Door Station
Purpose:
You can activate the online main door station, and configure the building No. for the
online main door station.
Steps:
1. Select the community, and press the Main Door Station tab to switch to the main
door station configuration interface.
Video Intercom Door Station·User Manual
36
Figure 7-34 Setting Main Door Station
2. Select the door station type from the drop-down list menu: Door Station for Unit, or
Door Station for Villa.
3. Enter the main door station start IP address, set the main door station floor No., and
then click the Calculate button to generate the main door station end IP address and
main door station No. (like 1-1-1) automatically.
4. Set the linked network parameters for the main door station: SIP IP address, master
station IP address, center IP address, center port No., subnet mask, and gateway
address.
5. Select an online door station, enter the login password, and click the Set button.
The default main door station floor No. is 1.
For the login password, if the main door station has been activated, enter the
activation password here. If the main door station is not activated, create a login
password here, and the main door station will be activated simultaneously.
When the device is successfully configured, it prompts the note: Configuring main
door station parameters succeeded.
Video Intercom Door Station·User Manual
37
Setting Sub Door Station
Steps:
1. Select the community, and press the Sub Door Station tab to switch to the sub door
station configuration interface.
Figure 7-35 Setting Sub Door Station
2. Select the door station type from the drop-down list menu: Door Station for Unit, or
Door Station for Villa.
3. Set the sub door station parameters (sub door station amount, floor No., start IP
address, end IP address), and then click the Calculate button to generate the sub
door station end IP address and sub door station No. (like 1-1-1-1) automatically.
4. Set the linked network parameters for the sub door station: main door station IP
address, SIP IP address, master station IP address, center IP address, center port No.,
subnet mask, and gateway address.
5. Select an online door station, enter the login password, and click the Set button.
The default sub door station floor No. is 1.
Video Intercom Door Station·User Manual
38
Up to 8 sub door stations can be added to a main door station.
For the login password, if the sub door station has been activated, enter the
activation password here. If the sub door station is not activated, create a login
password here, and the sub door station will be activated simultaneously.
When the device is successfully configured, it prompts the note: Configuring main
door station parameters succeeded
7.6 Batch Upgrading
In the device list area, click to enter the batch upgrading interface.
Figure 7-36 Batch Upgrading
7.6.1 Adding Devices for Upgrading
You should add the device to the batch upgrading tool first before upgrading the device.
There are 2 ways to add the device: adding online device, and adding by IP address/IP
segment.
Adding Online Device
Steps:
1. In the batch upgrading interface, click the to open the online device
window.
Video Intercom Door Station·User Manual
39
Figure 7-37 Login
2. Select a device, enter the user name and password, and click the Login Device button.
3. Click the Add Device button, and the device is added to the batch upgrading tool.
Figure 7-38 Online Devices
Video Intercom Door Station·User Manual
40
Adding by IP Address/IP Segment
Steps:
1. Click the Manual button to open the device adding window.
2. Enter the corresponding information (IP address, user name, password, start IP
address, end IP address).
3. Click the Add button.
Figure 7-39 Adding by IP Address/IP Segment
7.6.2 Upgrading Devices
There are 2 upgrading modes available: upgrading by file, and online upgrading.
Upgrading by File
Upgrading by File: You upgrade the device or devices via the local upgrade files.
Steps:
1. Select a device or multiple devices, and select “Upgrade by File” as the upgrading
mode.
2. Click to pop up the window for opening the upgrading file.
Video Intercom Door Station·User Manual
41
Figure 7-40 Upgrade by File
3. Open the upgrading file, and click the Upgrade button.
Online Upgrading
Online Upgrading: The batch upgrading tool will search the latest upgrading file for the
device automatically. You upgrade the device or devices via the local upgrade files.
Steps:
1. Select a device or multiple devices, and select “Online Upgrading” as the upgrading
mode.
2. Click the Download button. Click the Upgrade button after the online upgrading file
has been wholly downloaded.
Video Intercom Door Station·User Manual
42
8 Remote Operation via iVMS-4200
The Video Intercom module provides remote control and configuration on video
intercom products via the iVMS-4200 client software.
Before remote configure and control the video intercom, you are required to add the
device to the software first. Refer to 8.2 Device Management.
For remote configuration of video intercom device via the iVMS-4200 client software,
refer to 8.3 Configuring Devices Remotely via iVMS-4200.
For the picture storage on storage server, refer to 8.4 Picture Storage.
For remote control of video intercom devices, please refer to 8.5 Video Intercom
Configuration.
8.1 System Configuration
Purpose:
You can configure the video intercom parameters accordingly.
Steps:
1. Open the System Configuration page.
Path: Control Panel -> Maintenance and Management -> System Configuration ->
Video Intercom.
2. Click the Video Intercom tab to enter the Video Intercom Settings interface.
3. Input the required information.
Ringtone: Click the icon and select the audio file from the local path for the
ringtone of indoor station. Optionally, you can click the icon for a testing of the
audio file.
Max. Ring Duration: Input the maximum duration of the ringtone, ranging from 15
seconds to 60 seconds.
Max. Speaking Duration with Indoor Station: Input the maximum duration of
speaking with the indoor station, ranging from 120 seconds to 600 seconds.
Max. Speaking Duration with Door Station: Input the maximum duration of speaking
with the door station, ranging from 90 seconds to 120 seconds.
Card Reader Type: Select the card reader to issue cards.
4. Click Save to save the settings.
Video Intercom Door Station·User Manual
43
Figure 8-1 System Configuration Interface
8.2 Device Management
Purpose:
Device management includes device activation, adding device, editing device, and
deleting device, and so on.
After running the iVMS-4200, video intercom devices should be added to the client
software for remote configuration and management.
8.2.1 Adding Video Intercom Devices
You can add at most 512 indoor stations and master stations in total to the
iVMS-4200, and add at most 16 door stations to the iVMS-4200.
For video intercom devices, you are required to create the password to activate them
before they can be added to the software and work properly. For device activation via
creating password, please refer User Manual of iVMS-4200 (Video Intercom) V2.4.2 in
the disk for detail steps.
You can add online video intercom devices, and add them manually. Here take adding
online video intercom devices as example. For adding video intercom devices
manually, please refer User Manual of iVMS-4200 (Video Intercom) V2.4.2 in the disk
for detail steps.
Steps:
Video Intercom Door Station·User Manual
44
1. Click the icon on the control panel, or click Tools->Device Management to
open the Device Management page.
2. Click the Server tab.
To add indoor station or master station:
1) Click Add New Device Type to enter add new device type interface.
Select Indoor Station/Master Station and click OK.
Figure 8-2 Adding New Device Type
2) In the Server tab, Video Intercom Device will display, select Video Intercom
Device and add indoor station and master station.
To add door station:
In the Server tab, select Encoding Device/Outdoor Device and add door
station.
3. The active online devices in the same local subnet with the client software will be
displayed on the Online Device area. You can click the Refresh Every 60s button to
refresh the information of the online devices.
Figure 8-3 Online Device
To add online devices to the software, you are required to change the device IP
address to the same subnet with your computer first.
4. Select the devices to be added from the list.
Video Intercom Door Station·User Manual
45
5. Click Add to Client to open the device adding dialog box.
6. Input the required information.
Nickname: Edit a name for the device as you want.
Address: Input the device’s IP address. The IP address of the device is obtained
automatically in this adding mode.
Port: Input the device’s port No.. The default value is 8000.
User Name: Input the device’s user name. By default, the user name is admin.
Password: Input the device password. By default, the password is 12345.
7. Optionally, you can check the checkbox Export to Group to create a group by the
device name. All the channels of the device will be imported to the corresponding
group by default.
iVMS-4200 also provides a method to add the offline devices. Check the checkbox
Add Offline Device, input the required information and the device channel number
and alarm input number, and then click Add. When the offline device comes online,
the software will connect it automatically.
8. Click Add to add the device.
Figure 8-4 Adding Device by IP/Domain
Add Multiple Online Devices
If you want to add multiple online devices to the client software, click and hold Ctrl key
to select multiple devices, and click Add to Client to open the device adding dialog box.
Video Intercom Door Station·User Manual
46
In the pop-up message box, enter the user name and password for the devices to be
added.
Add All the Online Devices
If you want to add all the online devices to the client software, click Add All and click OK
in the pop-up message box. Then enter the user name and password for the devices to
be added.
8.2.2 Modifying Network Information
Select the device from the online list, click Modify Netinfo, and then you can modify the
network information of the selected device.
Figure 8-5 Modifying Network Parameter
You should enter the admin password of the device in the Password field of the pop-up
window to modify the parameters.
8.2.3 Resetting Password
According to the different video intercom devices, the software provides two different
methods for restoring the default password or resetting the password.
Select the device from the online device list, click Reset Password.
Option 1:
If the window with import file button, key importing mode drop-down list, password
and confirm password field pops up, follow the steps below to reset the password:
Video Intercom Door Station·User Manual
47
This option is available to door stations.
Figure 8-6 Resetting Password (Option 1)
1. Click Export to save the device file on your computer.
2. Send the file to our technical engineers.
3. Our technical engineer will send you a file to you. After receiving a file from the
technical engineer, select Import File from Key Importing Mode drop-down list and
click to import the file.
4. Input new password in text fields of Password and Confirm Password.
5. Click OK to reset the password.
STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong
password of your own choosing (Using a minimum of 8 characters,
including at least three of the following categories: upper case letters,
lower case letters, numbers, and special characters.) in order to
increase the security of your product. And we recommend you reset
your password regularly, especially in the high security system,
resetting the password monthly or weekly can better protect your product.
Option 2:
If the window with import file and export file buttons, password and confirm password
field pops up, follow the steps below to reset the password:
Note: This option is available to indoor stations and master stations.
Video Intercom Door Station·User Manual
48
Figure 8-7 Resetting Password (Option 2)
1. Click Export to save the device file on your computer.
2. Send the file to our technical engineers.
3. Click Import and select the file received from the technical engineer.
4. Input new password in text fields of Password and Confirm Password.
5. Click OK to reset the password.
STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong
password of your own choosing (Using a minimum of 8 characters,
including at least three of the following categories: upper case letters,
lower case letters, numbers, and special characters.) in order to
increase the security of your product. And we recommend you reset
your password regularly, especially in the high security system,
resetting the password monthly or weekly can better protect your product.
8.3 Configuring Devices Remotely via iVMS-4200
Configuring devices remotely via iVMS-4200 is the same with that via Batch
Configuration Tool, please refer 7.4 Configuring Devices Remotely for detail steps.
8.4 Picture Storage
When the video intercom device is under armed status, it will capture the picture
automatically after unlocking the door. The captured picture can be uploaded and stored
in the storage server.
Video Intercom Door Station·User Manual
49
When starting the live view of door station via iVMS-4200, you can capture the live view
picture. The captured picture can be uploaded and stored in the storage server.
This function is only available to door stations.
You are required to add storage server to the iVMS-4200, and format the HDDs first
before uploading and storing captured pictures.
8.4.1 Adding Storage Server
Before you start:
The storage server application software needs to be installed and it is packed in the
iVMS-4200 software package. When installing the iVMS-4200, check the checkbox of
Storage Server to enable the installation of storage server.
1. Click the icon on the desktop to run the storage server.
2. Open the Device Management page and click the Server tab.
3. Click Add New Device Type, select Storage Server and click OK.
Figure 8-8 Adding Storage Server Type
4. Click Storage Server on the list to enter the Storage Server Adding interface.
For adding the storage server, please refer to User Manual of iVMS-4200 (Video
Intercom) V2.4.2 in the disk.
Video Intercom Door Station·User Manual
50
8.4.2 Formatting the HDDs
The HDDs of the storage server need to be formatted for the captured picture storage.
Steps:
1. Select the added storage server from the list and click Remote Config.
2. Click Storage->General to enter the HDD Formatting interface.
3. Select the HDD from the list and click Format. You can check the formatting process
from the process bar and the status of the formatted HDD changes from Unformatted
to Normal Status.
Figure 8-9 Formatting HDDs
Formatting the HDDs is to pre-allocate the disk space for storage and the original data of
the formatted HDDs will be deleted.
8.4.3 Configuring Storage Server Picture Storage
Before you start:
The storage server needs to be added to the client software and the HDDs need to be
formatted for the captured pictures storage.
Video Intercom Door Station·User Manual
51
Steps:
1. Open the Record Schedule page.
2. Select the camera from the Camera Group list.
3. Select the storage server from the Storage Server drop-down list.
You can click Storage Server Management to add, edit or delete the storage server.
4. Check the checkbox of Picture Storage to store the alarm pictures of the camera
when event occurs.
Figure 8-10 Setting Storage Server
5. Click Set Quota to enter the HDD management interface of the storage server. You
can set the corresponding quota ratio for captured picture information.
Video Intercom Door Station·User Manual
52
Figure 8-11 Setting Quota
Example: If you set the picture quota as 60%, then the 60% of the storage space
can be used for storing the captured pictures.
6. Click Save to save the settings.
8.5 Video Intercom Configuration
Click the icon on the control panel of iVMS-4200 or click View -> Video
Intercom to open the Video Intercom page. On the Video Intercom page, you can
control video intercom devices remotely. There are 4 modules on the Video Intercom
page:
Video Intercom: Start visual communication with door stations, and manage
incoming calls from indoor stations and door stations and master stations. Refer
8.5.2 Video Intercom for detail steps.
Group Management: Construct virtual communities according to the real
community situations, and assign door stations and indoor stations to the
community accordingly. Refer 8.5.1 Group Management for detail steps.
You should manage groups first before starting the visual communication with
indoor stations or door stations.
Video Intercom Door Station·User Manual
53
Card Management: Add unauthorized cards to the iVMS-4200, and issue card to
the door station via the iVMS-4200. Refer 8.5.3 Card Management for detail steps.
Once you issue cards via the iVMS-4200, the card issuing function of the
corresponding door station will be disabled automatically.
Notice Management: Send information to indoor stations, search information,
search call logs, and search unlocking logs. Refer 8.5.4 Notice Management for
detail steps.
Figure 8-12 Intercom Interface
8.5.1 Group Management
Purpose:
You can add groups to community, outer door station, or other, and assign devices to
each group.
Enter Control Panel -> Video Intercom -> Group Management to add, edit, and delete
groups. Three group types can be selected: community, outer door station and other.
Adding Group
1. Click the Group Management tab to enter the group management interface.
Video Intercom Door Station·User Manual
54
Figure 8-13 Adding Group
2. Click to pop up group adding window, and input the corresponding information
accordingly.
Select Community as group type, and then Input the Community No.,
building No., and Unit No. to set the community structure, as shown in the
figure below.
Figure 8-14 Adding Community
Select Outer Door Station as group type, and then input the outer door
station No. (Range: 1 to 9) to set the outer door station, as shown in the
figure below.
Video Intercom Door Station·User Manual
55
Figure 8-15 Adding Outer Door Station
Select Other as group type, and then input the group name.
Figure 8-16 Adding Other
For example: You can name the group as administrator, entrance guard and cleaning
staff, etc.
When selecting Other as the group type, you can set different groups for staff other
than residents, such as administrator, security guard and cleaning staff, etc., and you
can assign cards to these staff and configure different permissions to them.
3. Click OK to complete group adding.
Video Intercom Door Station·User Manual
56
Assigning IP Devices to Group
After adding groups to Community, Outer Door Station, or Other, you should assign
devices to the group.
For example: You should assign indoor stations and door stations to the group 1-1-1 in
Community.
1. Click Add to enter the Add Resident Interface and the video intercom devices added
to the client software will be listed, as shown in the figure below.
Figure 8-17 Adding Resident
2. Check the checkbox of device.
Indoor Station: set a Room No. for the indoor station.
Door Station: set a No. for the door station.
3. Click OK to save the settings.
Assigning Analog Devices to Group
When assigning analog devices to group, only analog indoor stations are supported.
1. Click Add Analog to pop up analog device adding window. You can add analog devices
singly or in batch.
Video Intercom Door Station·User Manual
57
Adding Devices in Batch: Enter the start floor and end floor, and set the room
numbers.
Figure 8-18 Adding Devices in Batch
Room Numbers here refers to the room numbers in each floor.
Adding Devices Singlly: Enter the room No..
Figure 8-19 Adding Device Singly
The room No. format is like 101.
2. Click OK to save the settings.
Video Intercom Door Station·User Manual
58
Modifying Device Information
1. Select an added device.
2. Click Modify to enter the device modifying interface.
Figure 8-20 Modifying Device Information
3. Click OK to complete the device modifying operation.
Deleting Device
1. Select an added device.
2. Click Remove to pop up a dialog box.
Figure 8-21 Information
3. Click OK to complete the group deleting operation.
8.5.2 Video Intercom
Receiving Call from Door Station
Purpose:
When the door station has been added to the client software, you can call iVMS-4200
via door station.
Before you start:
Make sure the door station has been added to the iVMS-4200 client software.
Video Intercom Door Station·User Manual
59
Make sure the SIP server IP address of the door station is not configured (or
abnormal).
Steps:
Press Calling Center key on the door station.
Figure 8-22 Calling from Door Station
When the SIP server IP of the door station is configured, press Calling Center key on
the door station to call the master station instead of iVMS-4200.
Click Unlock to unlock the building or villa door via iVMS-4200, no matter whether
answering the call from door station or not.
Click Answer to answer the call from door station.
Click Hang Up to end the call from door station.
Call Log
On the Video Intercom tab page, there are four types of call logs you can search: All,
Dialed, Received, and Missed.
On the dial log area, you can view detail information of the dialog, and click Call to start
the audiovisual call with the indoor station.
Click to clear all logs in the list (optional).
Video Intercom Door Station·User Manual
60
8.5.3 Card Management
Purpose:
You can add unauthorized cards to the community and then you can assign the cards to
the corresponding indoor station and door stations.
For example, if there are 3 residents living in Room 401, you can assign 3 cards to No.
401 Indoor Station.
For each indoor station, you can assign multiple cards, and you can assign these cards to
the door station in the same building.
Note: Indoor extension does not support Card Management.
Before you start:
Make sure the indoor station and door station have been added to the iVMS-4200 client
software.
Steps:
Click Video Intercom -> Card Management to enter the card management page.
Figure 8-23 Card Management Interface
Adding Card
Steps:
1. Click Unauthorized Card -> Add Card to pop up card adding window.
Video Intercom Door Station·User Manual
61
Figure 8-24 Adding Cards in Batch
2. Select card adding mode and card type.
Two types of card are available. Resident Card is used by residents living in the
community, and Other Card is used by visitors (guest, serviceman, etc.) in the
community.
If you add card in batch, please set the start card No. and the end card No..
If you add card singly, please enter the card No..
If you add card via card reader, please swipe the card in the card reader, and the
corresponding card No. will be shown automatically in the Card No. textbox.
3. Click OK to accomplish carding adding operation.
Click Delete All to delete all cards added in iVMS-4200.
Select one or multiple cards, and click Delete Card to delete selected cards added in
iVMS-4200.
Card Encrypt is only available to cards added via card reader. Enabling Card Encrypt
can improve the card security to prevent it from being copied. But the same time, the
default key of all the available sectors of the card is modified.
Issuing Card
Click Issue Card to pop up card issuing window.
Video Intercom Door Station·User Manual
62
Figure 8-25 Issuing Card
Issuing Resident Cards
Steps:
1. Select Community from the organization list (like 1-1-1) and the indoor stations of the
community will be listed in the resident list.
Figure 8-26 Clicking Card Selection
Video Intercom Door Station·User Manual
63
2. Click Card Selection to pop up card selection window where unauthorized resident
cards are listed.
Figure 8-27 Selecting Cards
3. Check the checkboxes of the cards or enter the card No. in the filter textbox you need
to assign to the indoor station, and check the checkbox of door stations, doorphones
and outer door stations.
Only resident cards can be assigned to indoor stations.
4. Click Issue Card to complete the card issuing operation.
Video Intercom Door Station·User Manual
64
Figure 8-28 Displaying Card Issued
After issuing resident cards to the indoor station, the card No. will also be listed in the
resident list.
Issuing Other Cards
Steps:
1. Select Other from the group list (like Cleaning Staff).
Figure 8-29 Issuing Other Card
Video Intercom Door Station·User Manual
65
2. Click Card Selection to pop up card selection window where unauthorized other cards
are listed.
Figure 8-30 Selecting Cards
3. Check the checkboxes of the cards or enter the card No. in the filter textbox you need
to assign to the person, and check the checkbox of door stations, doorphones and
outer door stations.
4. Click Issue Card to complete the card issuing operation.
Video Intercom Door Station·User Manual
66
Figure 8-31 Displaying Card Issued
After issuing other cards to the person, the card No. will also be listed in the resident
list page.
Canceling Cards
When canceling cards, cards that have been issued will be reset to authorized ones. Via
iVMS-4200, there are two ways to cancel the cards which have been issued.
Option 1:
Steps:
1. Select Community from the organization list (like 1-1-1) and the indoor stations of the
community will be listed in the resident list.
Video Intercom Door Station·User Manual
67
Figure 8-32 Card Selection Interface
2. Click Card Selection to pop up card selection window where normal cards and
unauthorized resident cards are listed.
Figure 8-33 Selecting Cards
3. Check the checkboxes of the cards that has been issued (normal cards).
4. Click Issue Card to complete the card canceling operation.
Option 2:
Video Intercom Door Station·User Manual
68
On the card issuing interface, check the checkboxes of Room No. (for resident card) or
Name (for other card), click Cancel Card to cancel all card issued to the device.
Through Option 1, you can cancel card from single or certain door stations.
Through Option 2, you will cancel all issued cards at a time.
Normal Card
Click Normal Card to display normal card list. After issuing cards, the issued cards will be
listed in the normal card list, as shown in the figure below.
Figure 8-34 Normal Cards Interface
Batch Importing Unauthorized Cards
Steps:
1. Click Batch Import to enter the batch import interface, as shown in the figure below.
Video Intercom Door Station·User Manual
69
Figure 8-35 Importing File
2. Click Export Template to export the template of the batch import file.
3. Fill in the template of the batch import file and save it.
4. Click to select the batch import file and click Open.
5. Click OK to start importing the batch import file.
Batch Exporting Unauthorized Cards
Steps:
1. After adding unauthorized cards, and click Batch Export.
2. Select the saving file path and click Save.
3. After batch exporting the unauthorized cards, the excel will be generated in the saving
directory.
8.5.4 Notice Management
Querying Call Logs
Steps:
1. Click Query Call Logs to enter the call log querying page.
2. Select the calling status, device type, and set the start time and end time, and click
Query to search the call log.
Video Intercom Door Station·User Manual
70
Figure 8-36 Call Log Interface
3. Click Export to export the call logs as an excel file.
Querying Unlocking Log
Steps:
1. Click Query Unlocking Logs to enter the unlocking log querying page.
2. Select the unlocking type, device type, and set the start time and end time, and click
Query.
Video Intercom Door Station·User Manual
71
Figure 8-37 Unlocking Log Interface
3. Click Export to export the unlocking logs as an excel file.
8.6 Device Arming Control
Steps:
1. Select Tool->Device Arming Control to pop up device arming control window.
Figure 8-38 Tool Bar
Video Intercom Door Station·User Manual
72
2. Set the arming status of the device as armed, and the alarm information will be auto
uploaded to the client software when alarm occurs.
Figure 8-39 Device Arming Control
Figure 8-40 Alarm Events
After adding the device to the client software, it will be armed automatically.
Video Intercom Door Station·User Manual
73
9 Local Operation
9.1 Calling Resident
9.1.1 Calling Resident (DS-KV8X02-IM)
You can call the resident by pressing the call button. For device DS-KV8X02- IM, the
number of call buttons varies according to its model.
Take the figure of device DS-KV8402-IM as an example.
For device DS-KV8102-IM, there is only 1 call button.
For device DS-KV8202-IM, there are 2 call buttons.
For device DS-KV8402-IM, there are 4 call buttons.
Default settings of call button: when you press the call button, it calls the resident;
and when you hold down the call button, it calls the center.
You can change the calling mode of the call button via Batch Configuration Tool or
iVMS-4200 client software. See 7.4.2 Video Intercom for detail steps.
Figure 9-1 Call Button of DS-KV8402-IM
Steps:
1. Press the corresponding call button of the resident.
2. The resident can receive/decline the video call, unlock the door, call the elevator, etc.
Video Intercom Door Station·User Manual
74
When the video intercom between you and the resident is realized, you can speak to
the resident, and the live view of door station will be displayed on the connected
indoor station.
When live view of door station is displayed on other devices or door station is calling
resident, the door station will detect the brightness of video. When the brightness is
lower than the expected threshold, the supplement light will be enabled.
When the supplement light is enabled, the backlight of key will be auto-enabled,
otherwise, the door station will detect the brightness of live view and enable the
backlight of key when the brightness of live view is lower than expected threshold.
9.1.2 Calling Resident (DS-KV8102-XP)
You can call the resident by pressing the call button. For device DS-KV8102-IP/VP, there
is only 1 call button.
Default settings of call button: when you press the call button, it calls the resident;
and when you hold down the call button, it calls the center.
You can change the calling mode of the call button via Batch Configuration Tool or
iVMS-4200 client software. See 7.4.2 Video Intercom for detail steps.
Figure 9-2 Call Button of DS-KV8102-XP
Steps:
1. Press the corresponding call button of the resident.
Video Intercom Door Station·User Manual
75
2. The resident can receive/decline the video call, unlock the door, call the elevator, etc.
When the video intercom between you and the resident is realized, you can speak to
the resident, and the live view of door station will be displayed on the connected
indoor station.
When live view of door station is displayed on other devices or door station is calling
resident, the door station will detect the brightness of video. When the brightness is
lower than the expected threshold, the supplement light will be enabled.
When the supplement light is enabled, the backlight of key will be auto-enabled,
otherwise, the door station will detect the brightness of live view and enable the
backlight of key when the brightness of live view is lower than expected threshold.
9.2 Issuing Card
Purpose:
You can assign the card to the door station or doorphone by issuing cards. You can issue
cards by swiping the main card with the door station, or issue the card with iVMS-4200
client software. For more information about issuing card by iVMS-4200, please refer to
the user manual in the disk.
Steps:
1. Swipe the main card on the card induction area to enter the card issuing mode.
2. Hear a voice prompt of the device: Issuing card started.
3. Swipe the unauthorized sub card in turn on the card induction area.
4. Hear a voice prompt of the device (Issuing card finished.) after issuing each card
successfully.
Only Mifare card supported, and Mifare card with non-standard shape is
recommended.
No more than 256 cards can be issued to and managed by V series door station. A
voice prompt (Card amount exceeds limit.) can be heard when the issued card amount
exceeds the upper limit.
Swipe the main card again or perform no operation for more than 10s, the device will
exit the card issuing mode automatically.
After issuing cards with client software, the local card issuing function will be
disabled.
For each main door station, at most 8 sub door stations can be added.
Video Intercom Door Station·User Manual
76
9.3 Unlocking Door
Purpose:
After issuing cards, you can unlock the door by swiping the issued card.
Step:
1. Swipe the card on the card induction area.
2. Hear a voice prompt of the device: Door is open.
You cannot unlock the door by swiping the main card.
Video Intercom Door Station·User Manual
77
Appendix
Installation Notice
While installing the door station, please make sure that the distance between any two
devices is far as possible to avoid the howling and echo. The distance between two
devices is recommended to be longer than 10 meters.
Devices here refer to indoor station, door station, doorphone and master station.
Wiring Cables
Cable
Specification
Power Cord of Door Station
RVV 2*1.0
Network Cable of Door Station
UTP-five Categories
Door Lock Wiring (With Door Magnetic)
RVV 4*1.0
Door Lock Wiring (Without Door Magnetic)
RVV 2*1.0
Exit Button Wiring
RVV 2*0.5
Video Intercom Door Station·User Manual
78
… 5 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hikvision DS-KV8202 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hikvision DS-KV8202 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Hikvision DS-KV8202

Hikvision DS-KV8202 Snelstart handleiding - English - 32 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info