742714
13
Verklein
Vergroot
Pagina terug
1/256
Pagina verder
13
English
(*1) Removing and inserting the battery
NOTE
Ensure that the battery cover is securely closed unless
you are removing or installing the battery.
If any water, concrete, or dust enters the body of the
power tool or the terminals of the battery, a failure may
occur.
(*2) Low-speed / High-speed changeover
CAUTION
Avoid mixing viscous materials in Mode 2 (High speed).
The motor will stop if it detects an excessive load.
Overloading may damage the tool.
To change speed, rotate the shift lever as indicated by the
arrow. The numeral “1” engraved on the machine body
denotes low speed, the numeral “2” denotes high speed.
If it is hard to turn the shift lever, turn the shaft slightly in
either direction and then turn the gear shift lever again.
NOTE
Align the arrow on the shift lever to one of the numbered
positions.
Use with the shift lever set between the numbered
positions may damage the tool.
Rotate the shift lever only when the motor is not
operating.
Changing the shift lever position while the motor is
running may damage the tool.
Mode
Mode 1
(Low speed)
Mode 2
(High speed)
Rotation
speed
0 – 500 min
-1
0 – 1200 min
-1
Usage
High viscosity
materials
(e.g., mortar or
leveling mortar)
Low viscosity
materials
(e.g., paint)
(*3) Mounting and dismounting of the holder
Attached to the main unit when packing.
(*4) Mounting of the screw
CAUTION
Take extreme care to avoid injury when mounting or
detaching the mixing screw.
(*5) How to use
NOTE
Ensure that the mixing container is placed in a rm and
secure position.
A container that is not properly secured may move
unexpectedly.
Place the mixing screw inside the container and check
for safety before turning on the switch.
Once mixing is complete, wait for the mixing screw to
come to a complete stop before removing it from the
container.
Start mixing at low speed. Assess mixing status before
adjusting the speed.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to turned o the switch and remove the battery
before maintenance and inspection.
1. Mixing screw cleaning
To extend the life of the screw and shaft, clean by
washing in water after use.
CAUTION
Do not leave the tool with the mixing screw immersed in
plaster.
Doing so may result in corrosion and aking of the screw
surface and plaster contamination.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
5. Cleaning on the outside
After using the power tool, wipe the tool body (in
particular, the ventilation holes, areas around the switch
trigger, and areas near the edges of the covers require
careful wiping) to remove any concrete using a cloth that
is soaked in a soap solution and well wrung.
Do not use gasoline, thinner, benzine, or kerosene as
they can dissolve plastics.
Immediately remove any concrete that has become
attached to the exible assembly.
6. Storage
Store the power tool in a place in which the temperature
is less than 40°C and out of reach of children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when
the battery is disassembled and modi ed (such as
disassembly and replacement of cells or other internal
parts).
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country speci c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
0000Book_UM36DA_EU.indb 130000Book_UM36DA_EU.indb 13 2020/07/03 10:33:112020/07/03 10:33:11
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hikoki UM 36DA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hikoki UM 36DA in de taal/talen: Alle talen als bijlage per email.

De handleiding is 9,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info