Handleiding Hikoki RH600T (pagina 8 van 48) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans)

816296

Verklein

Vergroot

Pagina terug

1/48

Pagina verder

English

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the

power requirements speciﬁ ed on the product nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

3. Extension cord

When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

BASIC FUNCTIONS

1. Switch Operations and Temperature Adjustments

(Fig. 1, 2)

Press the switch upward or downward to enable

continual operations even when your ﬁ nger is removed.

Press the protrusion lightly to return the switch to the

central position and turn oﬀ the power.

The wind temperature and wind volume can be adjusted

in two stages depending on which way the switch is set.

Switch [I] position:

110 V: 250°C (wind volume 0.25 m3)

120 V to 127 V: 350°C (wind volume 0.25 m3)

220 V to 240 V: 350°C (wind volume 0.25 m3)

Switch [II] position:

110 V to 127 V: 500°C (wind volume 0.5 m3)

220 V to 240 V: 600°C (wind volume 0.5 m3)

Press the quick cooling button and press the switch to

blow warm air at approximately 50 degrees Celsius for

each of the switch’s wind volumes.

This is used to quickly cool material that is heat-

warping and to cool the nozzle when it reaches high

temperatures after using the tool.

2. Using the Hook (Fig. 3)

CAUTION

○ When pointing the tool upward to work, make sure that

it is placed on a stable block that does not tilt.

○ Do not hang the tool from your wrist or waist when

moving around with the nozzle still hot.

Support the tool ﬁ rmly when pointing the heat-wind release

nozzle upward.

Also, it is possible to suspend the tool from a wrist, etc.,

with a cord to prevent it from being dropped when working

in high locations, etc.

3. Attaching the Nozzle (Fig. 4)

CAUTION

The nozzle is extremely hot immediately after use, so

do not touch it.

NOTE

Make sure you do not drop the nozzle.

Replace the nozzle for a type that is suited to the job in hand.

Insert the nozzle supplied ﬁ rmly into the hot wind release

nozzle until it can go no further.

4. Temperature Settings

WARNING

○ Do not use the tool in the vicinity of volatile substances

(thinner, gasoline, etc.)

○ Do not bring the hot wind release nozzle in close

contact with your hands or face during use.

The nozzle is extremely hot immediately after use, so

do not touch it.

Set the temperature in consideration of the article to be

heated.

Also, pay attention to the surrounding material that will be

heated at the same time.

First of all, apply the hot wind from a distance while checking

that there are no changes in the article being heated, and

then move it closer until it reaches an appropriate distance.

Heating inﬂ ammable substances

(paper, wood, plastic, etc.)

Set the switch to the [I] position and apply the heat with

the nozzle at least 10cm away from the article being

heated.

Gently move the tip of the nozzle up, down, left and right

to apply the heat.

Applying heat constantly to one location may result in

malformation or the outbreak of smoke.

Heating non-ﬂ ammable substances

(metal, stone, concrete, etc.)

Set the switch to the [I] position, and if there are no

problems, move it to the [II] position.

Apply the heat with the nozzle at least 5cm away from

the article being heated.

Holding the nozzle too close may result in the tool

overheating, leading to malfunctions.

WORK EXAMPLE

CAUTION

Parts of the nozzles supplied are sharp, so use gloves

when removing them from the case and when attaching

or detaching them.

Select the nozzle in consideration of the shape of the

article being heated and the area being heated.

1. Peeling oﬀ paint (Fig. 5)

Use nozzle (ﬂ at) or nozzle (round) to soften the paint

with the hot wind, and then remove it with the scraper

supplied.

Note that heating the paint too much may result in it

scorching and becoming harder, making it diﬃ cult to

scrape oﬀ .

2. Softening adhesive (Fig. 6)

Use nozzle (ﬂ at) or nozzle (round) to soften the surface

and make it easy to peel, and then pull up one of the

edges, blow heat underneath it and gently peel it oﬀ so

that none of the adhesive remains.

3. Heat wrapping (Fig. 7)

Use nozzle (ﬂ at) to heat-wrap shrink ﬁ lm and tubes. The

material will change color or crack if hot air is blown onto

it from a close distance, so maintain an appropriate

distance while monitoring progress.

4. Forming resin pipes (Fig. 8)

Use nozzle (curved surface) to evenly heat the

circumference of the resin pipe.

To prevent the inside of the pipe from narrowing when

bending it, etc., pour sand inside, block both ends and

then gently bend it.

5. Removing putty from window frames (Fig. 9)

Use nozzle (glass protector) to soften the putty with heat,

and then remove the putty with the scraper supplied.

Note that glass may crack if heat is continually applied

to it.

6. Defrosting water pipes (Fig. 10)

Use nozzle (curved surface) to heat the frozen area from

the edge to the center. Do not mistake water pipes for

glass pipes.

Take care to avoid damaging frozen resin areas on

water pipes.

00BookRH600TWE.indb800BookRH600TWE.indb8 2019/07/1210:33:352019/07/1210:33:35

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Hikoki RH600T Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info