Handleiding Hikoki RH18DA (pagina 11 van 240) (Alle talen)

816236

Verklein

Vergroot

Pagina terug

1/240

Pagina verder

English

NOTE

○ There may be a diﬀ erence between the displayed

temperature and the actual temperature.

○ Press and hold the + and - temperature control buttons

at the same time to switch between Fahrenheit (°F) and

Celsius (°C).

Set the temperature in consideration of the article to be

heated.

Also, pay attention to the surrounding material that will be

heated at the same time.

First of all, apply the hot air from a distance while checking

that there are no changes in the article being heated, and

then move it closer until it reaches an appropriate distance.

Heating inﬂ ammable substances

(paper, wood, plastic, etc.)

Set the switch to the [set I] position and apply the heat

with the nozzle at least 10 cm away from the article being

heated.

Gently move the tip of the nozzle up, down, left and right

to apply the heat.

Applying heat constantly to one location may result in

malformation or the outbreak of smoke.

Heating non-ﬂ ammable substances

(metal, stone, concrete, etc.)

Set the switch to the [set I] position, and if there are no

problems, move it to the [set II] position.

Apply the heat with the nozzle at least 5 cm away from

the article being heated.

Holding the nozzle too close may result in the tool

overheating, leading to malfunctions.

*2 Remaining battery indicator

Use as a guide only.

State of lamp Battery Remaining Power

Over 70%

55%–70%

35%–55%

20%–35%

Less than 20%

NOTE

When using a battery with a remaining battery indicator,

please refer to the indicator lamp on the battery for the

battery remaining power.

*3 How to use the hook

CAUTION

Do not hang the tool from your wrist or waist whenmoving

around with the nozzle still hot.

*4 Attaching/removing the nozzle

CAUTION

The nozzle is extremely hot immediately after use, so do

not touch it.

Insert the nozzle ﬁ rmly into the front cover until it can go no

further.

You can remove the nozzle without touching it by rotating the

front cover counterclockwise.

NOTE

○ Be careful not to remove the nozzle during work.

○ When removing it, be careful not to damage the

surroundings or the nozzle.

*5 Work facing up

CAUTION

When using the tool facing up, place it on a stable

surface.

When working with both hands, such as when bending

a pipe, you can lay down the heat gun and use it with the

nozzle side facing up.

WORK EXAMPLE

CAUTION

Parts of the nozzles supplied are sharp, so use gloves

when removing them from the case and when attaching

or detaching them.

Select the nozzle in consideration of the shape of the

article being heated and the area being heated.

NOTE

Do not block the intake or nozzle during use.

1. Peeling oﬀ paint (Fig. 11)

Use nozzle (plane) or nozzle (round) to soften the paint

with the hot air, and then remove it with the scraper.

Note that heating the paint too much may result in it

scorching and becoming harder, making it diﬃ cult to

scrape oﬀ .

2. Softening adhesive (Fig. 12)

Use nozzle (plane) or nozzle (round) to soften the

surface and make it easy to peel, and then pull up one of

the edges, blow heat underneath it and gently peel it oﬀ

so that none of the adhesive remains.

3. Heat wrapping (Fig. 13)

Use nozzle (plane) to heat-wrap shrink ﬁ lm and tubes.

The material will change color or crack if hot air is blown

onto it from a close distance, so maintain an appropriate

distance while monitoring progress.

4. Forming resin pipes (Fig. 14)

Use nozzle (curved surface) to evenly heat the

circumference of the resin pipe.

To prevent the inside of the pipe from narrowing when

bending it, etc., pour sand inside, block both ends and

then gently bend it.

5. Defrosting water pipes (Fig. 15)

Use nozzle (curved surface) to heat the frozen area from

the edge to the center. Do not mistake gas pipes for water

pipes and heat them.

Take care to avoid damaging frozen resin areas on water

pipes.

WARNING SIGNALS

This product features functions that are designed to protect

the tool itself as well as the battery. If any of the safeguard

functions are triggered during work, the LED light and the

temperature display will blink for a few seconds as described

in Table 3. When any of the safeguard functions are

triggered, immediately switch oﬀ and follow the instructions

described under corrective action.

Table 3

Safeguard

Function LED light

Display Display Corrective

Action

Overload

Protection On 0.5 sec. /

oﬀ 0.5 sec.

Remove the

cause of the

overload.

Temperature

Protection

Allow the tool

and battery

to thoroughly

cool.

00BookRH18DAEU.indb1100BookRH18DAEU.indb11 2022/12/2010:06:512022/12/2010:06:51

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Hikoki RH18DA Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info