816435
9
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
English
9
MAINTENANCE
MAINTENANCE, REPLACEMENT OR REPAIR OF THE
EMISSION CONTROL DEVICES AND SYSTEMS MAY
BE PERFORMED BY ANY NON-ROAD ENGINE REPAIR
ESTABLISHMENT OR INDIVIDUAL.
Carburetor adjustment (Fig. 13)
The carburetor is a precision part that mixes air and fuel, and
it is designed to ensure high performance from the engine.
Before the tool is shipped from the factory, its carburetor is
adjusted during a test run. Only make adjustments if it is
necessary because of environmental conditions (the climate
or atmospheric pressure), the type of fuel, the type of two-
cycle oil, etc.
WARNING
Because the carburetor is manufactured with a high
degree of precision, do not disassemble it.
For this product, the only setting of the carburetor that
can be adjusted is the idle speed (T).
T = Idle speed adjustment screw.
Idle speed adjustment (T)
Check that the air lter is clean. If adjustment is required,
turn IDLE speed Adjustment Screw (T) close (clockwise)
to increase engine speed, open (counterclockwise) to
decrease engine speed. Standard Idle rpm is 2800-
3200 rpm.
CAUTION
The above adjusting procedure must be followed when
adjustment is MADE or DAMAGE to engine will occur
because of the incorrect condition.
NOTE
Some models sold areas with strict exhaust emission
regulation do not have high and low speed carburetor
adjustments. Such adjustments may allow the engine to
be operated outside of their emission compliance limits.
For these models, the only carburetor adjustment is idle
speed.
RECOMMENDATION
CARBURETOR ADJUSTMENT NEEDS THE SKILL
OF EXPERIENCED OR WELL TRAINED PEOPLE, OR
IS RECOMMENDED TO TAKE THE UNIT TO HiKOKI
Authorized Service Centers.
Air lter (Fig. 14)
The air lter (11) must be cleaned from dust and dirt in order
to avoid:
Carburetor malfunctions.
Starting problems.
Engine power reduction.
Unnecessary wear on the engine parts.
Abnormal fuel consumption.
Clean the air lter daily or more often if working in
exceptionally dusty areas.
Cleaning the air lter (Fig. 14)
Open the air lter cover (12) and remove the air lter (11).
Clean it.
Check that the lter is dry before reassembly.
An air lter that has been used for some time cannot be
cleaned completely. Therefore, it must regularly be replaced
with a new one. A damaged lter must always be replaced.
Fuel lter (Fig. 15)
Remove the fuel lter (13) from the fuel tank, and replace it
if it is dirty.
NOTE
A blocked fuel lter (13) can prevent the supply of fuel
and cause a rotation malfunction of the engine.
Spark plug (Fig. 16)
When removing the spark plug, twist and remove the plug
cap covering the spark plug as shown in the illustration.
(Fig. 17)
The spark plug condition is in uenced by:
An incorrect carburetor setting.
Wrong fuel mixture (too much oil in the gasoline)
A dirty air lter.
Hard running conditions (such as cold weather).
These factors cause deposits on the spark plug electrodes,
which may result in malfunction and starting di culties. If
the engine is low on power, di cult to start or runs poorly at
idling speed, always check the spark plug rst.
If the spark plug is dirty, clean it and check the electrode
gap. Re-adjust if necessary. The correct gap is 0.6 mm.
The spark plug should be replaced after about 100
operation hours or earlier if the electrodes are badly
eroded.
NOTE
In some areas, local law requires using a resistor spark
plug to suppress ignition signals. If this machine was
originally equipped with resistor spark plug, use same
type of spark plug for replacement.
For long-term storage
Drain all fuel from the fuel tank. Start and let engine run until
it stops. Repair any damage which has resulted from use.
Clean the unit with a clean rag, or the use of high pressure
air hose. Put a few drops of two-cycle engine oil into the
cylinder through the spark plug hole, and spin the engine
over several times to distribute oil.
Cover the unit and store it in a dry area.
Maintenance schedule
Below you will nd some general maintenance instructions.
For further information please contact HiKOKI Authorized
Service Centers.
Daily maintenance
Clean the exterior of the unit.
Check that the air intake at the guard net is not clogged.
Check the guard net for damage or cracks. Change the
guard net in case of impacts or cracks.
Check that nuts and screws are su ciently tightened.
Weekly maintenance
Check the starter, especially the cord.
Clean the exterior of the spark plug.
Remove the spark plug and check the electrode gap.
Adjust it to 0.6 mm, or change the spark plug.
Clean the air lter.
Monthly maintenance
Rinse the fuel tank with gasoline, and clean fuel lter.
Clean the exterior of the carburetor and the space
around it.
Quarterly maintenance
Clean the cooling ns on the cylinder.
Clean the fan and the space around it.
Clean the mu er of carbon.
CAUTION
Cleaning of cylinder ns, fan and mu er shall be done
by a HiKOKI Authorized Service Center.
SELECTING ACCESSORIES
The accessories of this machine are listed on page 193.
000BookRB27EAP.indb9000BookRB27EAP.indb9 2018/12/149:11:252018/12/149:11:25
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hikoki RB27EP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hikoki RB27EP in de taal/talen: Alle talen als bijlage per email.

De handleiding is 19.45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info