Handleiding Hikoki N 14DSL (pagina 21 van 200) (Alle talen)

742724

Verklein

Vergroot

Pagina terug

1/200

Pagina verder

Anti Blank Firing Mechanism

The stapler is equipped with an anti blank ﬁ ring

mechanism to prevent blank ﬁ ring when the staples run

out.

The stapler will cease to operate when eight or fewer

staples remain.

Approximately eight staples will remain after ﬁ ring a

strip of staples, but replenishing the magazine with the

same staples will enable stapling to be continued.

1. Stapling procedures

WARNING

○ Never point the discharge outlet at people.

○ Make sure that work is carried out with the discharge

outlet well away from faces, hands, feet and other parts

of the body.

○ Do not ﬁ re staples directly onto existing staples.

○ Remove the battery when the stapler is not being used

and during work breaks.

○ When work has been completed, remove the battery,

and then remove the remaining staples.

○ When pulling the trigger, make sure that other ﬁ ngers

are not touching the push lever.

Failure to observe this may result in injury.

NOTE

○ There are cases in which operations will become

sluggish if used at low ambient temperatures.

○ There are cases in which the staples will bend or cracks

will appear in the stapled material depending on the

hardness, thickness and combinations of the material.

Test the stapling operability before commencing full

use.

(1) Locking the trigger and removing the battery

Remove the battery from the stapler to prevent

unexpected operations. (Fig. 2)

(2) Loading staples

Load staples of a size appropriate for the job in hand

into the magazine. (Fig. 6)

(3) Attaching the battery

Place the battery onto the stapler and press on it until it

clicks into place.

(4) Releasing the lever lock

Slide the lock lever until the lock has been released.

(Fig. 4)

(5) Firing staples

Adjust the depth of the staples with the adjuster.

(Fig. 9)

(6) Finishing work

When work has been ﬁ nished, lock the trigger and

remove the battery, and then remove all of the staples

from the magazine.

2. How to adjust the stapling depth (Fig. 9)

WARNING

When adjusting staple depth, aim the discharge outlet

downwards and check that it is not pointing at faces,

hands, feet or other parts of the body ﬁ rst of all, and

then lock the trigger.

Fire a test staple, and if it is too deep adjust the depth

by rotating the adjuster to drive it shallower.

If the staple is not driven in deep enough, rotate the

adjuster to drive it deeper.

The adjuster rotation modiﬁ es the depth by up to 2 mm.

3. Using the hook

The hook is used to hang up the power tool to your

waist belt while working.

CAUTION

○ When using the hook, hang up the power tool ﬁ rmly not

to drop accidentally.

If the power tool is dropped, it may lead to an accident.

○ Make sure the trigger has been locked and the battery

removed when using the hook.

○ Install securely the hook. Unless the hook is securely

installed, it may cause an injury while using.

(1) Removing the hook.

Remove the screws ﬁ xing the hook with Philips screw

driver. (Fig. 10)

(2)

Replacing the hook and tightening the screws.

Install securely the hook in the groove of power tool and

tighten the screws to ﬁ x the hook ﬁ rmly. (Fig. 11)

MAINTENANCE AND INSPECTION

WARNING

Make sure the trigger has been locked and the

battery removed before carrying out inspections and

maintenance. Also make sure that the recharger has

been unplugged.

1. Removing Staple Jams (Fig. 12)

(1) Remove the battery from the power tool.

(2) Press the stop lever, slide open the magazine and

remove all staples.

(3) Remove adhesive of staples, fragments and splinters

that have collected in the blade guide with a ﬂ athead

screwdriver or similar implement.

(4) Check to ascertain that the push lever works smoothly.

NOTE

After removing staple jams, reload the staples and ﬁ re

a test staple.

2. Magazine Inspections

The inside of the magazine needs to be cleaned from

time to time. Slide the magazine open and remove

adhesive of staples, fragments and splinters that have

collected.

NOTE

Dirt inside the magazine may result in the operations of

the staple feeder becoming sluggish, which may cause

blank ﬁ ring.

3. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws

be loose, retighten them immediately. Failure to do so

may result in serious hazard.

4. Cleaning of the outside

When the power tool is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not use

chloric solvents, gasoline or paint thinner, as they melt

plastics.

5. Storage

Store the power tool in a place in which the temperature

is less than 40°C, and out of reach of children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries

dead and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

English

0000Book_N14DSL.indb 210000Book_N14DSL.indb 21 2020/04/17 14:16:222020/04/17 14:16:22

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Hikoki N 14DSL Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info