816290
5
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
5
English
<Capacity with Angle attachment (Optional accessory for D13VF and D13VG)>
Model D13VF D13VG
Speed of angle unit LOW
(650
min–1
)HIGH
(1350
min–1
)LOW
(400
min–1
)HIGH
(900
min–1
)
Capacity
Steel Twist Bit 13 mm 13 mm 13 mm 13 mm
Hole Saw 64 mm 32 mm 70 mm 51 mm
Wood
Flat Spade Bit 40 mm 32 mm 40 mm 40 mm
Auger Bit 38 mm 29 mm 38 mm 32 mm
Hole Saw 114 mm 64 mm 114 mm 102 mm
NOTE
Due to HiKOKI’s continuing program of research and development, the speci cations herein are subject to change
without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Fixing and removing side handle
1 113
Fixing and removing side handle and
handle joint 2 113
Mounting and dismounting the bit 3 113
Dismounting the bit (When the drill
chuck cannot be loosened) 4 114
Selecting rotational direction 5 114
Switch operation 6 114
Locking-on the switch 7 114
Releasing the switch 8 114
Dismounting drill chuck from tool 9 114
Mounting angle attachment (Optional
accessory) 10 115
Selecting speed of angle attachment 11 115
Dismounting drill chuck from angle
attachment 12 115
Fixing side handle for angle attachment
13 115
Mounting position of hook (A)*3
(Optional accessory) 14 115
Selecting accessories 116
*3 Attaching the hook. (Optional accessory)
To attach the hook, it is necessary to disassemble the
handle portion which covered the tool’s electrical system.
For your continued safety and electrical shock protection,
installing the hook on this drill should ONLY be performed
by a HiKOKI AUTHORIZED SERVICE CENTER.
Selecting the appropriate drill bit
When boring metal or plastic
Use ordinary metalworking drill bits.
Sizes range from a minimum of 1.2 mm to chuck
maximum capacity.
When boring wood
Use ordinary woodworking drill bits.
However, when drilling 6.5 mm or smaller holes, use a
metalworking drill bit.
MAINTENANCE AND INSPECTION
1. Inspecting the drill bits
Since use of an abraded drill bits will cause motor
malfunctioning and degraded e ciency, replace the drill
bits with a new one or resharpening without delay when
abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes
For your continued safety and electrical shock protection,
carbon brush inspection and replacement on this tool
should ONLY be performed by a HiKOKI Authorized
Service Center.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
GUARANTEE
We guarantee HiKOKI power tools in accordance with
statutory/country speci c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the power tool, undismantled, with the GUARANTEE
CERTIFICATE
found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
00BookD10VF.indb500BookD10VF.indb5 2022/12/2711:24:132022/12/2711:24:13
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hikoki D13VG bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hikoki D13VG in de taal/talen: Alle talen als bijlage per email.

De handleiding is 12.13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info