816239
13
Verklein
Vergroot
Pagina terug
1/248
Pagina verder
13
English
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your
dealer or the HiKOKI Authorized Service Center.
1. Power tool
Symptom Possible cause Remedy
Tool does not operate. No remaining battery power Charge the battery.
The battery has not been properly
installed. Remove the storage battery from the battery
compartment in the tool and check for foreign
matter. Also check the battery electrodes for
soiling. Make sure that the battery is pressed in
until it clicks into place.
Foreign matter is lodged in the
blade. When there is foreign matter in the blade, remove
the battery and use a pair of tongs or similar tool
to remove it.
Take great care since the tool may start
operating when the foreign matter has been
removed.
Sap or rust may also prevent the blade from
operating. Use a wire brush or similar tool to
remove sap or rust.
The tool has been used for heavy
work. This is the e ect of a function that protects the
battery by turning o the motor when the tool
is exposed to an excessive load. Release the
switch and remove what caused the excessive
load and pull back the switch to resume work.
Tool does not trim well. The blade has become dull. Use a wire brush or other tool to remove sap
and rust and use a le or whetstone to sharpen
the blade. If these e orts fail to make the blade
sharper, the blade has reached the end of its
service life. Replace the blade with a new one.
The blade stopped because it
was used to cut a branch whose
width exceeded the blade’s cutting
capacity.
NOTE
Work that will repeatedly cause
the blade to stop will eventually
damage the motor.
Some garden trees have wood that is very hard
and may be beyond the capacity of the tool even
if it is of a width that is within normal capacity.
Use a pair of pruning shear to remove thick
branches before starting work.
An oblique cut may also exceed the capacity of
the tool since the length of the cut increases. Be
sure to trim thick branches at right angles.
Tool suddenly stopped Tool was overburdened Get rid of the problem causing the overburden.
The battery is overheated. Let the battery cool down.
Battery cannot be installed Attempting to install a battery other
than that speci ed for the tool. Please install a multi volt type battery.
0000BookCH3656DA.indb130000BookCH3656DA.indb13 2023/05/0911:26:332023/05/0911:26:33
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hikoki CH3672DA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hikoki CH3672DA in de taal/talen: Alle talen als bijlage per email.

De handleiding is 8.08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info