816321
18
Verklein
Vergroot
Pagina terug
1/332
Pagina verder
18
English
Information concerning airborne noise and vibration
The measured values were determined according to
EN60745 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 96 dB (A)
Measured A-weighted sound pressure level: 85 dB (A)
Uncertainty K: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN60745.
Cutting metal:
Vibration emission value ah = 2.5 m/s2
Uncertainty K = 1.5 m/s2
The declared vibration total value has been measured in
accordance with a standard test method and may be used
for comparing one tool with another.
It may also be used in a preliminary assessment of exposure.
WARNING
The vibration emission during actual use of the power
tool can di er from the declared total value depending in
the ways in which the tool is used.
Identify safety measures to protect the operator that
are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is
switched o and when it is running idle in addition to the
trigger time).
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your
dealer or the HiKOKI Authorized Service Center.
1. Power tool
Symptom Possible cause Remedy
The unit does not run/is
stopped The battery capacity is depleted Charge the storage battery.
The unit has stopped
suddenly
The unit is overloaded Get rid of the cause of the large load.
The storage battery is overheated Allow the storage battery to cool su ciently.
The band saw blade has
come loose
There is oil or grime adhering to the band
saw blade or workpiece Wipe o oil or grime that is adhering to the
band saw blade or workpiece.
The band saw blade is not installed correctly Install the band saw blade correctly.
(See “Replacing the band saw blade”)
The band saw blade is
becoming bound in the
workpiece
A band saw blade operating speed
appropriate for the workpiece is not being
used
Select the correct band saw blade operating
speed.
(See “Adjusting operating speed”)
Cutting precision is poor
The band saw blade is worn away Replace the band saw blade with a new
one.
A band saw blade operating speed
appropriate for the workpiece is not being
used
Select the correct band saw blade operating
speed.
(See “Adjusting operating speed”)
The band saw blade is not installed correctly Install the band saw blade correctly.
(See “Replacing the band saw blade”)
The gaps between the band saw blade ball
bearing supports have become wide
Correctly adjust the gaps.
(See “Inspection of band saw blade ball
bearing supports and adjustment of gaps”)
A band saw blade that is not authorized by
the manufacturer is being used Use a band saw blade that is authorized by
the manufacturer.
Su cient warm-up cuts have not been
performed
With the band saw blade operating speed
setting dial set to “1”, perform 1 or 2 warm-
up cuts with a light cutting load such as a
cylindrical rod (carbon steel, etc.) with an
outer diameter of 20 mm or less.
00BookCB3612DA.indb1800BookCB3612DA.indb18 2022/07/0116:49:022022/07/0116:49:02
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hikoki CB3612DA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hikoki CB3612DA in de taal/talen: Alle talen als bijlage per email.

De handleiding is 19.21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info