700147
16
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
16
INSTALLATION INSTRUCTIONS
ELECTRICAL INTERCONNECTION
Installation of RCA/Audio signal cables and power supply.
Please install if possible the audio cables from the headunit and the amplifier not together with the power
supply wires on the same side of the vehicle. The best is an areal separated installation in the left and right
cable channel of the vehicle. This avoids an overlap of interferences on the audio signal. This also applies
for the supplied bass-remote connection, which should not be installed together with the power supply
wires. It is recommended to use the same side like the audio cables.
REFERENCE NOTE
BATT+12V
Connect both BATT+12V-terminals with the +12V pole of the vehicle’s battery. Use a suitable cable with a sufficient cross section
and install an additional in-line fuse. For safety reasons the distance between the fuseblock and the battery must be shorter than
30 cm. Do not install the fuse into the fuseblock until the installation is accomplished.
GND
Connect this GROUND terminal with a suitable contact ground point on the vehicle’s chassis. The ground wire must be as short
as possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground point has a stable
and safe electric connection to the negative “–”pole of the battery. Check this ground wire from the battery to the ground point if
possible and enforce it, if required.
REM
Connect the turn-on signal (e.g. automatic antenna) or the turn-on remote signal of your headunit with the REM-terminal of the
amplifier. Use therefor a suitable cable with a sufficient cross section (0,5 mm
2
). Thereby the amplifier will turn on or off automatically
with your headunit.
LOGO BADGE
With this switch you can choose between white or blue illumination of the upper logo badge.
Always follow the guidelines of your national road traffic regulations.
3
1
2
3
4
BEFORE THE CONNECTION
For the professional installation of a sound system appropriate wiring kits are available in car audio retailer stores. Attend the sufficient
profile section (attend the specifications below), the suitable fuse rating and the conductivity of the cables when you purchase your wiring
kit. Clean and remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection. Make sure that
all screws are fixed tight after the installation, because loosely connections may cause malfunctions, unsufficient power supply or
interferences.
41
IMPORTANT NOTE: Due to the very high power consumption, the X4-MAXXIMUS model has two power terminals, which
must be both connected. Furthermore we suggest the installation of an additional battery. Please use a power wiring
with a crosssection of at least 2 x 35mm
2
in 4 ohm-operation.
IMPORTANT NOTE: The X4-MAXXIMUS model has due to construction-conditioned reasons no internal fuse-protection.
The amplifier must be fused with an external In-Line-Fuse aan the following fuse values:
200 A in 4 Ohm-operation
300 A in 2 Ohm-operation
400 A in 1 Ohm-operation
2
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hifonics X4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hifonics X4 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 3,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info