700163
24
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
9
1
The LINE IN RCA jacks must be connected with the RCA output jacks of the headunit.
By connecting only the CH1/2 jacks, the INPUT switch must be set to the 2CH position.
3
The HPF controller (HIGHPASS) of CH1/2 and CH3/4 adjusts the cut-off point of the frequency range to below for each channelpair.
The cut-off frequency is continuously adjustable from 10 Hz to 1200 Hz (1.2 kHz).
6
The CH1/2 X-OVER MODE switch selects the required operation mode of this channelpair.
Position DUPE: This mode should be selected, if you want to run 2 subwoofers bridged in LPF/BPF mode. The DUPE mode
passes (duplicate) the signal from CH3/4 to the line input section of CH1/2. All controllers and settings except the LEVEL controller
are then without function. The LINE IN RCAs of CH1/2 are deactivated.
Position HPF: Highpass mode (the higher frequencies will be eliminate. Adjustable by the HPF controller.)
Position FULL: Fullrange mode (the whole frequencies will be amplified).
ENG|MERCURY IV
24
7
The CH3/4 BOOST controller defines the bass bosst from 0 to 12dB @ 50Hz on channelpair 3/4.
9
FUNCTIONS AND OPERATIONAL CONTROLS
2
The LINE OUT RCA jacks provide a summed mono audiosignal to supply an additional subwoofer amplifier.
4
The LPF controller (LOW PASS) on CH3/4 adjusts the cut-off point of the frequency range to above. The cut-off frequency is
continuously adjustable from 30 Hz to 150 Hz.
5
The LEVEL controller adjusts the input sensitivity of the amplifier to align the audio signal from the head unit for each channelpair.
The input sensitivity is adjustable from 6 Volts (MIN) to 0.2 Volts (MAX).
The BASS LEVEL CONTROLLER port is for the cable of the enclosed bass remote controller. With this bass remote controller,
you are able to adjust the bass level e.g. out of the driver’s seat. Please use only the enclosed bass remote controller and cable.
The controller works only in LPF/BPF and only on CH3/4. In DUPE mode operation it also works on CH1/2. For more details check
the information on page 21, section #8.
11
The CH3/4 X-OVER MODE switch selects the required operation mode of this channelpair.
Position LPF/BPF: Lowpass mode (the higher frequencies will be eliminated. Adjustable by the LPF controller.)
The HPF controller works in this operation mode as subsonicfilter and eliminates the lower frequencies (Bandpass-Mode).
NOTE: If this controller is turned to a higher value than the LPF controller, no sound is hearable.
Position HPF: Highpass mode (the higher frequencies will be eliminate. Adjustable by the HPF controller.)
Position FULL: Fullrange mode (the whole frequencies will be amplified).
7
The INPUT switch must be in 2CH position, if you connect only one RCA stereo audio cable on the CH1/2 LINE IN.
Select position 4CH, if you connect two RCA stereo audio cables on CH1/2 and CH3/4 line inputs. The fader function of your
headunit works only in the 4CH mode. If you have select the 2CH mode, the input signal of LINE INPUT CH1/2 will be passed
to CH3/4. Due to this, only one RCA stereo audio cable is required and no Y-Adaptors are required.
8
864321 10 115
POWER/PROTECT (Also located on the supplied Bass Level Controller)
If the POWER LED lights up, the amplifier is ready for operation.
If the PROTECT LED lights up, a malfunction is indicated. Observe in this case the chapter TROUBLE SHOOTING.
10
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hifonics Mercury II bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hifonics Mercury II in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 3,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info