700124
19
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
19
FUNCTIONAL INSTRUCTIONS
SPEAKER CABLES
SHIELD
TO THE LINE IN ON THE
AMPLIFIER
CORE CONDUCTOR
HI LEVEL INPUTS & AUTO TURN ON
If your head unit has no pre-amplier low level RCA outputs or doesn’t provide a separate remote turn on wire (like described on
page 19/#2), follow these instructions:
AUTO TURN ON
Bring the AUTO TURN ON switch to position ON to activate the auto turn on function. This function only works, if the push button
INPUT LEVEL MODE is in HI position, the switch INPUT MODE in 2CH position and highlevel inputs (speaker outputs from the
headunit) are connected at the LINE IN CH1 & CH2. Please check the regarding notes below.
The amplier detects now by the so called ”DC Offset” (a voltage increase to 6 volts on the high level speaker outputs) if the
head unit is turned on and the amplier turns automatically on. As soon as the head unit is turned off, the amplier shuts down
automatically after approx.one minute.
NOTE: The AUTO TURN ON usually works with 90% of all headunits, because they are equipped with the ”High Power” outputs.
Only with a few older headunits the AUTO TURN ON function is not applicable.
The port of the remote connector of the amplier (page 19#2, REM) can now be used also to turn on additional other ampliers.
Connect the REM ports of the ampliers and ensure, that the other amplier’s AUTO TURN ON function is deactivated.
High level speaker cables as signal input:
Please use the optional HF-HLA adaptor from HiFonics (see
page 25). This adaptor is optmized for the use with this amplier
inputs and owns additionally a protect function for the speaker
outputs of your headunit.
Alternative: Solder the ends of the loudspeaker cables of the
head unit with common RCA connectors (separately available)
and connect them with LINE IN of the amplier.
The HI LEVEL INPUTS can be use independently from the AUTO
TURN ON function.
13
9
10
11
12
The LINE IN RCA jacks must be connected with the RCA output jacks of the headunit.
Please check also the notes in section #8 on the left..
The X-OVER switch selects the required operation mode of the amplier on Channel 1/2.
HP: Highpass mode (The higher frequencies will be eliminated. Adjustable by the HP controller).
FULL: Fullrange mode (All frequencies will be amplied).
The CH1/2 HP controller (high pass) adjust the cut-off point of the frequency range for Channel 1/2 to below. The cut-off frequen-
cy is continuously adjustable from 50Hz to 150 Hz..
The CH1/2 LEVEL controller adjust the input sensitivity of the amplier to align the audio signal of the head unit on Channel 1/2.
The input sensitivity is adjustable from 6 Volts (MIN) and 0.2 Volts (MAX).
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hifonics ARX3003 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hifonics ARX3003 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 6,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info