493446
1
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
CONTENTS
1. INTRODUCTION ................................................................................................................ 2
2.
MINIMUM SYSTEM REQUIREMENTS .............................................................................. 2
3. INSTALLATION ................................................................................................................. 3
3.1.
Installing drivers .......................................................................................................... 3
3.2. DJ Control MP3 e2 and your computer's sound card ................................................. 9
4. OVERVIEW ...................................................................................................................... 10
4.1.
The top face .............................................................................................................. 10
4.2.
USB connection ........................................................................................................ 11
5. USING DJ CONTROL MP3 E2 AT A PARTY ................................................................. 12
5.1.
Overview ................................................................................................................... 12
5.2. The DJ Control MP3 e2 control panel ....................................................................... 13
5.3.
Monitoring with headphones ..................................................................................... 14
5.4.
Speeding up or slowing down a track ....................................................................... 16
5.5.
Creating cue points ................................................................................................... 16
5.6. Creating loops ........................................................................................................... 17
5.7.
Switching from one track to another ......................................................................... 17
5.8.
Adding effects to a track ........................................................................................... 20
5.9.
Scratching ................................................................................................................. 20
6.
CONFIGURATION IN MIDI MODE .................................................................................. 22
7. FAQ ................................................................................................................................ 29
8. TECHNICAL SUPPORT .................................................................................................. 30
8.1.
Warranty information ................................................................................................. 30
8.2.
Additional warranty provisions .................................................................................. 31
ENVIRONMENTAL PROTECTION RECOMMENDATION ....................................................... 32
2/32User Manual
1. INTRODUCTION
DJ Control MP3 e2 is a high-performance DJ controller that opens up the doors to mixing and
scratching digital music on your computer. Intuitive and fun to use, DJ Control MP3 e2 lets you
put your own mark on your favorite music and share it with your friends to host great parties or
make creative mixes.
DJ Control MP3 e2 functions with digital audio files, including MP3s. We would like to draw your
attention to the fact that musical creations are protected by copyright and that you should comply
with all applicable laws. We strongly encourage you to support artists by acquiring their works
legally.
2. MINIMUM SYSTEM REQUIREMENTS
PC:
Desktop/laptop PC with Intel Pentium III/Athlon 1GHz or compatible processor or higher
Operating system: Microsoft Windows XP®, Vista®, 7™ (32 or 64-bit)
512MB RAM (Windows XP®); 1GB RAM (Windows Vista®, 7™) or higher
Available USB 2.0 port (recommended) or USB 1.1 port
Headphones or amplified speakers
CD-ROM or DVD-ROM drive
Graphics card supporting 1024 x 768 resolution
Sound card (preferably featuring 4-channel output (4.1) or greater to use the headphone
monitoring feature)
Internet connection (strongly recommended) + 100MB free disk space for some applications
Mac:
Desktop/laptop Mac with 1.5 GHz processor (G4, G5, Core Duo Series) or higher
Operating system: Mac OS 10.4 or 10.5
1GB RAM or higher
Available USB 2.0 port (recommended) or USB 1.1 port
Headphones or amplified speakers
CD-ROM or DVD-ROM drive
Graphics card supporting 1024 x 768 resolution
To use the headphone monitoring feature, you must have an external sound card featuring
4-channel output (4.1) or greater
Internet connection (strongly recommended) + 100MB free disk space for some applications
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual – 3/32
3. INSTALLATION
3.1. Installing drivers
- Insert the installation CD-ROM in your CD-ROM drive.
The installation menu for your DJ Control MP3 e2 appears
automatically.
- Click Install DJ Control MP3 e2.
If the installation menu is not launched
automatically:
PC:
- Double-click My Computer (Windows XP) or Computer
(Windows Vista / 7).
- Double-click the CD-ROM icon.
- Double-click the installer package.
Mac:
- Open your Finder.
- Double-click the CD-ROM icon.
- Double-click the installer package.
-
Click on the option to install the DJ Control MP3 e2 drivers
and follow the on-screen instructions.
We recommend that you connect DJ Control MP3 e2 to a USB 2.0 port directly on
your computer in order to enjoy the fastest transfer rates and optimal performance.
4/32User Manual
3.1.1. Installation in Windows Vista / 7
Once files have been copied to your computer, the drivers will be installed. Windows displays
three prompts in succession, regarding installation of the various components.
- Accept to install the software at each of these prompts to proceed with the installation.
A dialog box appears, prompting you to connect DJ Control MP3 e2 to your computer's USB port.
- Connect DJ Control MP3 e2 to your computer's USB port, then click Next.
Your computer automatically detects the DJ Control MP3 e2 and completes the installation of the
required drivers.
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual – 5/32
Please note that installation of the drivers may take some time, depending on your
computer’s performance. Let the installation procedure run its course and follow the on-screen
instructions.
You are notified when the installation is complete.
The DJ Control MP3 e2 icon appears in your Windows taskbar, next to the clock, indicating that
your DJ Control MP3 e2 is installed and ready for use:
To display the DJ icon in Windows 7, you must first click on the up arrow icon in the
notification area. When the list of hidden icons displays, drag-and-drop the DJ icon into the
notification area.
You should now install the VirtualDJ DJC Edition mixing software on your computer:
- In the installation menu, click Install VirtualDJ DJC Edition
and follow the on-screen instructions.
The software is installed on your computer. When installation is complete, the VirtualDJ icon
appears on your desktop.
- Double-click the VirtualDJ icon and enter the serial number, then click OK.
The serial number is found on the installation CD-ROM's envelope.
For more information on configuring your DJ Control MP3 E2, please refer to chapter
5.2. The DJ
Control MP3 e2 control panel
3.1.2. Installation in Windows XP
.
Once files have been copied to your computer, the drivers will be installed.
A dialog box appears, prompting you to connect DJ Control MP3 e2 to your computer's USB port.
6/32User Manual
- Connect DJ Control MP3 e2 to your computer's USB port, then click Next.
Your computer automatically detects the DJ Control MP3 e2 and completes the installation of the
required drivers.
NOTE: Do not interact with any Windows hardware detection windows that may appear during
the installation process; any such windows will disappear in a short while on their own.
Please note that installation of the drivers may take some time, depending on your
computer’s performance. Let the installation procedure run its course and follow the on-
screen instructions.
You are notified when the installation is complete.
The DJ Control MP3 e2 icon appears in your Windows taskbar, next to the clock, indicating that
your DJ Control MP3 e2 is installed and ready for use:
You should now install the VirtualDJ DJC Edition mixing software on your computer:
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual – 7/32
- In the installation menu, click Install VirtualDJ DJC Edition
and follow the on-screen instructions.
The software is installed on your computer. When installation is complete, the VirtualDJ icon
appears on your desktop.
- Double-click the VirtualDJ icon and enter the serial number, then click OK.
The serial number is found on the installation CD-ROM's envelope.
For more information on configuring your DJ Control MP3 E2, please refer to chapter
5.2. The DJ
Control MP3 e2 control panel
3.1.3. Installation on Mac
.
A welcome screen is displayed, informing you as to what will be installed.
- Follow the on-screen instructions.
You may need to enter your password in order to proceed if administrator access is
required on your system.
Once files have been copied to your computer, the drivers will be installed.
8/32User Manual
A dialog box appears, prompting you to connect DJ Control MP3 e2 to your computer's USB port.
- Connect DJ Control MP3 e2 to your computer's USB port.
Your computer automatically detects the DJ Control MP3 e2 and completes the installation of the
required drivers.
Please note that installation of the drivers may take some time, depending on your
computer’s performance. Let the installation procedure run its course and follow the on-
screen instructions.
You are notified when the installation is complete.
The DJ Control MP3 e2 icon appears on your desktop, indicating that your DJ Control MP3 e2 is
installed and ready for use:
You should now install the VirtualDJ DJC Edition mixing software on your computer:
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual – 9/32
- In the installation menu, click Install VirtualDJ DJC Edition
and follow the on-screen instructions.
The software is installed on your computer.
- To launch the VirtualDJ software on your Mac, go to Applications and then select VirtualDJ.
- Enter the VirtualDJ serial number, then click OK.
The serial number is found on the installation CD-ROM's envelope.
For more information on configuring your DJ Control MP3 E2, please refer to chapter
5.2. The DJ
Control MP3 e2 control panel
3.2. DJ Control MP3 e2 and your computer's sound card
.
DJ Control MP3 e2 is inseparable from your computer's sound card, speakers and/or
headphones. It is your sound card that will process the music being played on your computer.
The DJ Control MP3 e2 software allows you to control the music being outputted from your
computer. As the DJ Control MP3 e2 connects to your computer via a USB port, you can connect
it or disconnect it at any time, even when your computer is powered on, although not when the
VirtualDJ software is in use.
10/32User Manual
4. OVERVIEW
4.1. The top face
Your DJ Control MP3 e2 features a variety of controls allowing you to interact with DJ software.
There are two sets of these controls, as the left and right sections of the DJ Control MP3 e2 each
correspond to a separate deck in DJ software applications. Descriptions of the default function of
each control are provided below.
1 2 3 4 5 6 7 8 9 10 11 12 13
21 20 19 18 17 16 15 14
1. Decrease (-) or increase (+) speed of track (i.e. pitch) for accurate mixing
2. Using the Master Tempo function, the tone of the track stays unchanged when you change
the pitch
3. Pitch adjustment control knob
4. Toggle between control of loops or effects (when the button is not lit up, loops are enabled;
when the button is lit up, effects are enabled)
5. Cut or boost Treble/Medium/Bass frequencies
6. Folder button: switch the root directory
7. Enable scratch mode
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual 11/32
8. Move up ( ▲) or down ( ▼) through files
9. Automatically mix your entire playlist
10. File button: enter a directory
11. 1-2-3-4 buttons: Apply loops on 1, 2, 4 and 8 measures respectively, when in loop mode;
apply the corresponding effect when in effects mode
12. Next track/hold to fast-forward within track
13. Synchronize the beat with the beat of the track on the opposite deck
14. Play/Pause track
15. Set cue point (mark position in the track)
16. Vinyl-style jog wheel
17. Volume fader for corresponding deck
18. Load selected track on corresponding deck
19. Cross fader for seamless mixing between the 2 decks
20. Enable headphone monitoring on corresponding deck
21. Previous track/hold to rewind within track
These are descriptions of the DJ Control MP3 e2’s default functions, which may vary
according to the application you are using.
4.2. USB connection
DJ Control MP3 e2 has a USB connector on its back face, allowing you to connect it to your
computer. As DJ Control MP3 e2 is USB bus-powered, no external power source is required.
Back face
USB connector for
connection to computer
12/32User Manual
5. USING DJ CONTROL MP3 E2 AT A PARTY
5.1. Overview
You are now about to learn everything a DJ needs to know to host his or her first parties. Let’s
start at the beginning, namely setting up the party: no DJ would allow himself to arrive
unprepared, which is why he would have organized his material and selected his records
beforehand.
You should do the same by sorting through your music. Have a good look through your collection
of CDs as well as your MP3 and WMA files and select the songs you are going to use. In order to
be able to mix tracks effectively, you must know the tracks perfectly.
Once this is done, make sure that you have all the hardware you will need. Got your computer,
DJ Control MP3 e2, a pair of speakers and some headphones, if you have a multi-channel
sound card handy? Perfect, then you’re ready to go!
You’re probably asking yourself: and now, how do I get started? By way of introduction, here are
the basic principles of DJing: a DJ works with two decks (or turntables). The first deck plays one
track, while the DJ uses the second deck to get the next track ready. He can then work on this
second track (speed it up so that it is at the same tempo as the track that is currently playing, etc.)
before playing it out loud. Towards the end of a track, the DJ starts playing the track on the other
deck and does a mix, which is to say a blending of the two tracks to create a perfect transition.
The two decks share a single music list. You can load your tracks from the explorer window.
- Move the mouse pointer onto the MUSIC icon in the middle part of the screen.
The explorer window opens with the music list in the lower right-hand part of the screen.
Please read through the following sections to learn more about the art of DJing. We also
recommend that you consult the help documentation of the software supplied with your DJ
Control MP3 e2 for additional information.
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual 13/32
5.2. The DJ Control MP3 e2 control panel
You can access the control panel to configure your DJ Control MP3 e2.
5.2.1. Accessing the control panel in Windows
- Access the DJ Control MP3 e2 control panel via the Windows taskbar (in the lower right-hand
corner of your screen) by clicking the icon.
5.2.2. Accessing the control panel on Mac
- Access the control panel by double-clicking the icon on your desktop.
5.2.3. Control panel features
Main tab:
MIDI Channel for controls: Lets you select the MIDI channel on which MIDI commands are
sent to control your DJing software, apart from Virtual DJ which includes native support for DJ
Control MP3 e2.
Jog wheels settings
Enabling/Disabling: Lets you select whether to enable or disable the jog wheels.
Sensitivity: Lets you adjust the sensitivity of the jog wheels according to how you are using
them (scratching, setting up a track, etc.).
About tab:
This tab contains all of the information regarding the driver version currently installed. Please
refer to this information if you need to contact Hercules technical support.
14/32– User Manual
5.3. Monitoring with headphones
To prepare his musical line-up, a DJ uses headphone monitoring: he listens to a track on his
headphones while the other one is being played over the speakers, allowing him to adjust the
tempo so that the tracks flow seamlessly together. He can also add audio effects, set cue points
(markers) to start up at a specific point in a track, create rhythmic loops, adjust Treble, Medium
and Bass frequencies, and so on. Your DJ Control MP3 e2 allows you to carry out this kind of
headphone monitoring, depending on the hardware and software you have at your disposal.
If you only have a stereo sound card, you cannot carry out headphone monitoring.
Please note that both Mac desktop and laptop computers, as well as most PC laptops, feature
1 stereo output ONLY; so if you have such a computer and want to use the headphone
monitoring feature, you must have an external multi-channel sound card.
If you have a sound card with an output of 4 or more channels (such as the Hercules Muse
Pocket LT sound card, or a similar sound card and), however, you can monitor music on
outputs 3 and 4 over your headphones.
In order to use the headphone monitoring mode on your multi-channel sound card:
a) Verify that the speaker configuration is set to either 4 or 5.1 channels. This should
ideally be done using your sound card's configuration program.
Your operating system also offers certain configuration possibilities:
PC
- Sound and audio devices (Windows XP)
: Start > Control Panel
- Sound (Windows Vista / 7)
Mac
b) Make the necessary connections to your sound card as follows:
: Application > Utilities > Audio MIDI Setup
- Connect your speakers to the FRONT connector (usually green).
- Connect your headphones to the BACK/REAR connector (usually black).
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual 15/32
Please note that connector labels on certain sound cards may vary. Consult your sound
card’s documentation for specific details.
c) When running VirtualDJ for the first time, you will need to configure the software for
use with your sound card.
- Click the Config button.
- In the Sound Setup tab, configure as follows:
Input
: None
Output(s)
The adjacent menu should then display the default configuration: Master : Front output /
Headphones : Rear output.
: Headphone
Sound card
Select the sound card you want VirtualDJ to use in the the adjacent menu.
: 4.1 card (PC) / 4 Out Card (Mac)
You will need low impedance headphones for monitoring (less than 32 Ohms), as the sound level
will be too low if you use high impedance headphones. To monitor a deck, press the monitoring
button for the corresponding deck. Make sure to disable any 3D positioning features on your
sound card, or else you may end up hearing echoes of the track you are monitoring in your main
mix!
When a track on deck A is being played in the room, you should use your headphones to monitor
the track on deck B, and when a track on deck B is being played in the room, you should press
the headphone monitoring button on deck A to prepare the next track, and so on. When a
monitoring button is lit up on your DJ Control MP3 e2, it indicates that the deck in question is
being monitored.
In VirtualDJ, the boxes in the upper middle part of the screen representing decks 1 and 2 reflect
your monitoring status: in the case below, deck A (the left-hand deck, or deck 1 in VirtualDJ) is
green, indicating that it is being monitored on your headphones, while deck B (the right-hand
deck, or deck 2 in Virtual DJ) is red, indicating that it is not being monitored.
16/32User Manual
5.4. Speeding up or slowing down a track
The main reason for speeding up or slowing down a track you are about to play is to match its
BPM (i.e. the number of beats per minute) and synchronize its beat with that of the track already
playing. In this way you can mix the two tracks together smoothly when switching from one deck
to another. There are two ways to regulate the speed of a track: by manually adjusting its pitch,
and automatically via beat-matching.
On vinyl decks, the pitch allows you to adjust the rotation speed of the turntable. This adjustment
therefore changes the speed of a track by modifying its overall tonality (for example, a track that
has been sped up significantly will sound much more high-pitched, or sharper).
You can therefore use one of the DJ Control MP3 e2’s Pitch knobs to modify the pitch of a track.
VirtualDJ also offers a very useful function to automatically match the BPM of tracks that are
playing and synchronize their beats for easy mixing: this function is called beat-matching. Press
the Sync button on either deck to toggle beat-matching on and off for the deck in question. When
the Sync button stays lit up in blue, beat-matching is enabled on that deck; when the LED is off,
beat-matching is disabled on that deck.
When a track is being played on a deck, the BPM is displayed just above the track’s timeline, to the right (the
percentage next to the BPM indicates how much faster (+x.x%) or slower (-x.x%) the current BPM is in relation
to the track’s normal BPM):
- Press the Sync button on a deck to automatically match the BPM and synchronize the beat of the track on
that deck with that of the track playing on the other deck.
The Sync button lights up. This tracks BPM is automatically matched to that of the track being played on the
other deck and their beats are synchronized.
- Make a transition from one track to the other (please see section
5.7. Switching from one track to another
If you decide to switch off beat-matching on this deck, press the Sync button again. The Sync button goes
dim, indicating that beat-matching is now switched off.
).
5.5. Creating cue points
Finished synchronizing the tempos of your tracks? Great but depending on the tracks you are
using, you may wish to start up playback at a specific point and not simply at the beginning.
This is possible by inserting cue points into your tracks. A cue point allows you to locate the start
of an interesting rhythmic section and launch playback of a track at that section. VirtualDJ allows
you to set 1 cue point per track using your DJ Control MP3 e2
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual 17/32
To set a cue point:
- When you get to the rhythmic section you are looking for, press Play/Pause.
- Press CUE to set this position as cue point 1.
A marker
is inserted in the track’s timeline.
To go to a cue point when playing a track for the audience:
- Press Play/Pause to launch playback of the track from the cue point you have set.
5.6. Creating loops
Using the same marker principle, you can also create loops, which are sections of a track
repeated to infinity.
Loops are controlled using the 1, 2, 3 and 4 buttons in the Loops/Fx section of your DJ Control MP3 e2 which
generate loops based on 1, 2, 4 and 8 measures, respectively. Therefore, button 1 generates a short loop,
while button 4 generates a longer loop.
- Make sure that the Shift button in your DJ Control MP3 e2's Loops/Fx section is not lit up (if it is lit up, press
the Shift button to turn it off).
- During playback of the track
, when you get to a rhythmic section where you want to create a loop, press
button 1, 2, 3 or 4 (depending on how long you want the loop to be).
The rhythmic section is repeated to infinity.
- Press button 1, 2, 3 or 4 again to resume normal playback of the track.
5.7. Switching from one track to another
The art of mixing consists of preparing the next track while a given track is being played. When
the track being played reaches its end, the DJ switches from one track to the other progressively
using the cross fader, which regulates the volume of the two decks. This technique enables you
to avoid empty space between two tracks.
Your DJ Control MP3 e2 allows you to work with digital audio files stored on your computer. This
section will give you some practical examples of how you can switch from one musical track to
another using the VirtualDJ software if you are using headphone monitoring.
Example: An MP3 file is being played on deck A (the left-hand deck). You can change the EQ of
the track using the Treble, Medium and Bass knobs, so these knobs on deck A have been
adjusted for the perfect sound mix with the track that is playing. The cross fader is pushed
completely to the left, so only what is being played on deck A will be heard by the audience.
18/32User Manual
While the track on deck A is playing for the audience, press the headphone monitoring button on
deck B (the right-hand deck) so that you can hear the track you will be preparing on deck B on
your headphones while the audience continues to listen to the track being played on deck A over
the speakers in the room (assuming you have a multi-channel sound card that has been
configured for use with headphones in VirtualDJ, as described in chapter
5.3 Monitoring with
headphones
-
). The headphone monitoring button on deck B lights up, indicating that deck B is
being monitored on your headphones.
Step 1:
-
While the track on deck A is playing, mute the EQ controls (Treble, Medium and Bass
knobs) on deck B.
Step 2:
-
As the track on deck A is nearing its end, start up playback on deck B and start moving
the cross fader towards the center.
Step 3:
-
While the tracks on both decks are playing, restore the EQ controls (Treble, Medium
and Bass knobs) on deck B.
Step 4:
-
Mute the EQ controls (Treble, Medium and Bass knobs) on deck A.
Step 5:
-
Move the cross fader all the way to the right, to deck B.
Step 6:
The following diagrams give you an idea of how the Treble, Medium and Bass knobs and cross
fader are adjusted for the procedure described above.
Restore the EQ controls (Treble, Medium and Bass knobs) on deck A, so that you
can prepare the next track to be played on deck A on your headphones; and so on.
Step 1: Mute the EQ controls
(Treble, Medium and Bass
knobs) on deck B.
Step 2: Move the cross fader
to the center.
Step 3:
controls (Treble, Medium and
Bass knobs) on deck B.
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual 19/32
Step 4: Mute the EQ controls
(Treble, Medium and Bass
knobs) on deck A.
Step 5: Move the cross fader
all the way to deck B.
Step 6:
controls (Treble, Medium and
Bass knobs) on deck A.
Should you notice a slight discrepancy in the tempos of the two tracks, use the Pitch bend - / +
buttons. These buttons slow down or speed up playback; playback returns to the normal speed
when the button is released.
Simply repeat this procedure when you are getting ready to play your next track on deck A again.
In no time at all, you’ll be mixing like a pro!
The VirtualDJ software also features an automatic mixing function, which ensures the
adjustment of BPM between tracks and the switch from one deck to the other. This allows you
to take a well-deserved break during your mix without having to cut off the music and spoil the
mood in the room!.
- Move the mouse pointer onto the PLAYLIST icon in the lower right-hand part of the screen.
The playlist appears.
- Click
in the playlist window.
The automatic mixing function is enabled, and tracks will link up one after the other. To return to manual
mixing, click
again.
20/32User Manual
5.8. Adding effects to a track
If you want to call attention to a new track during your mix or prepare your audience for a
microphone address, you can add effects to tracks you are playing.
- Make sure that the Shift button in your DJ Control MP3 e2's Loops/Fx section is lit up (if it is not lit up, press
the Shift button to turn it on).
- Press button 1, 2, 3 or 4 to add the corresponding effects in VirtualDJ.
Note: in VirtualDJ, other effects can be set for buttons 1, 2, 3 and 4 by clicking .
5.9. Scratching
DJ Control MP3 e2 allows you to scratch your MP3s and CDs in the same way that a DJ
scratches vinyl records. To do this you will use the DJ Control MP3 e2’s jog wheels, together with
the cross fader to boost/interrupt the sound.
For the best results when using your DJ Control MP3 e2, try to position your hands as shown
below:
There are many scratch effects, the most well-known of which are described below:
Baby Scratch
No need to use the volume control for this basic scratch. It consists of doing a forward scratch,
immediately followed by a backward scratch.
Tear Scratch
The Tear Scratch doesn’t use the volume control either. As with the Baby Scratch, you do a
forward scratch followed by a backward scratch, but this backward scratch is broken down into
two different speeds: you must first scratch quickly, and then slowly. Thus, the different steps are
as follows: forward scratch, quick backward scratch, slow backward scratch.
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual 21/32
Forward Scratch
You must do a forward scratch and then quickly lower the volume to its minimum setting before
doing a backward scratch to return to the initial position and restore the volume. Only the forward
scratch will be audible.
Backward Scratch
The reverse of the Forward Scratch: you must do a backward scratch and then quickly lower the
volume to its minimum setting just before doing the forward scratch, and then restore the volume.
Pass-Pass
The Pass-Pass is not a scratch technique, strictly speaking, since it uses the scratch as well as
other elements (pitch, cross fader, etc.) to create new effects. To carry out this technique you
must play the same piece on both decks, and then it’s up to you to make use of the DJ Control
MP3 e2’s functions to create new rhythmic combinations by alternating your manipulations on
each deck. A perfect mastery of the cross fader and of the basic scratch techniques is required,
as well as a good sense of rhythm and excellent familiarity with the piece.
22/32User Manual
6. CONFIGURATION IN MIDI MODE
Your DJ Control MP3 e2 can function as a MIDI controller: the buttons, knobs, faders and jog
wheels can send MIDI signals that will then be interpreted by MIDI-capable software. In software
that accepts MIDI commands, you must select your DJ Control MP3 e2 as the MIDI controller.
3 signal types can be sent: simple instructions (pressed or released status) for the buttons, range
of values (from 0 to 127, depending on the position) for the 6 Treble/Medium/Bass knobs and the
3 faders, and variable speed modifiers (the value varying according to the rotation speed) for the
2 pitch knobs and the 2 jog wheels.
Many music software applications that incorporate MIDI control feature a “learning mode”: simply
click a button, turn a knob or jog wheel or move a slider on your DJ Control MP3 e2 to link that
control to a control in the software. Some popular applications to include a MIDI learning mode
include: Native Instruments Traktor, Ableton Live, Mixvibes, and Image Line Deckadance.
MIDI input
Control
Midi Control
Type
Midi
Command
(decimal)
Command Type
Midi Values
(decimal)
K1_DA
Note On/Note
Off
1
Button-Toggling
Output
“127” : Pressed 0”
: Released
K2_DA
Note On/Note
Off
2
Button-Toggling
Output
“127” : Pressed 0”
: Released
K3_DA
Note On/Note
Off
3
Button-Toggling
Output
“127” : Pressed 0”
: Released
K4_DA
Note On/Note
Off
4
Button-Toggling
Output
“127” : Pressed 0”
: Released
SHIFTED_K1_DA
Note On/Note
Off
5
Button-Toggling
Output
“127” : Pressed 0”
: Released
SHIFTED_K2_DA
Note On/Note
Off
6
Button-Toggling
Output
“127” : Pressed 0”
: Released
SHIFTED_K3_DA
Note On/Note
Off
7
Button-Toggling
Output
“127” : Pressed 0”
: Released
SHIFTED_K4_DA
Note On/Note
Off
8
Button-Toggling
Output
“127” : Pressed 0”
: Released
Shift_DA
Note On/Note
Off
9
Button-Toggling
Output
“127” : Pressed 0”
: Released
PBM_DA
Note On/Note
Off
10
Button-Toggling
Output
“127” : Pressed 0”
: Released
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual 23/32
PBP_DA
Note On/Note
Off
11
Button-Toggling
Output
“127” : Pressed 0”
: Released
Prev_DA
Note On/Note
Off
12
Button-Toggling
Output
“127” : Pressed 0”
: Released
Next_DA
Note On/Note
Off
13
Button-Toggling
Output
“127” : Pressed 0”
: Released
Cue_DA
Note On/Note
Off
14
Button-Toggling
Output
“127” : Pressed 0”
: Released
Play_DA
Note On/Note
Off
15
Button-Toggling
Output
“127” : Pressed 0”
: Released
Listen_DA
Note On/Note
Off
16
Button-Toggling
Output
“127” : Pressed 0”
: Released
Load_DA
Note On/Note
Off
17
Button-Toggling
Output
“127” : Pressed 0”
: Released
Sync_DA
Note On/Note
Off
18
Button-Toggling
Output
“127” : Pressed 0”
: Released
MTempo_DA
Note On/Note
Off
19
Button-Toggling
Output
“127” : Pressed 0”
: Released
Shift_State_DA
Note On/Note
Off
20
Button-Toggling
Output
“127” : Pressed 0”
: Released
K1_DB
Note On/Note
Off
21
Button-Toggling
Output
“127” : Pressed 0”
: Released
K2_DB
Note On/Note
Off
22
Button-Toggling
Output
“127” : Pressed 0”
: Released
K3_DB
Note On/Note
Off
23
Button-Toggling
Output
“127” : Pressed 0”
: Released
K4_DB
Note On/Note
Off
24
Button-Toggling
Output
“127” : Pressed 0”
: Released
SHIFTED_K1_DB
Note On/Note
Off
25
Button-Toggling
Output
“127” : Pressed 0”
: Released
SHIFTED_K2_DB
Note On/Note
Off
26
Button-Toggling
Output
“127” : Pressed 0”
: Released
SHIFTED_K3_DB
Note On/Note
Off
27
Button-Toggling
Output
“127” : Pressed 0”
: Released
SHIFTED_K4_DB
Note On/Note
Off
28
Button-Toggling
Output
“127” : Pressed 0”
: Released
Shift_DB
Note On/Note
Off
29
Button-Toggling
Output
“127” : Pressed 0”
: Released
24/32User Manual
PBM_DB
Note On/Note
Off
30
Button-Toggling
Output
“127” : Pressed 0”
: Released
PBP_DB
Note On/Note
Off
31
Button-Toggling
Output
“127” : Pressed 0”
: Released
Prev_DB
Note On/Note
Off
32
Button-Toggling
Output
“127” : Pressed 0”
: Released
Next_DB
Note On/Note
Off
33
Button-Toggling
Output
“127” : Pressed 0”
: Released
Cue_DB
Note On/Note
Off
34
Button-Toggling
Output
“127” : Pressed 0”
: Released
Play_DB
Note On/Note
Off
35
Button-Toggling
Output
“127” : Pressed 0”
: Released
Listen_DB
Note On/Note
Off
36
Button-Toggling
Output
“127” : Pressed 0”
: Released
Load_DB
Note On/Note
Off
37
Button-Toggling
Output
“127” : Pressed 0”
: Released
Sync_DB
Note On/Note
Off
38
Button-Toggling
Output
“127” : Pressed 0”
: Released
MTempo_DB
Note On/Note
Off
39
Button-Toggling
Output
“127” : Pressed 0”
: Released
Shift_State_DB
Note On/Note
Off
40
Button-Toggling
Output
“127” : Pressed 0”
: Released
Menu_U
Note On/Note
Off
41
Button-Toggling
Output
“127” : Pressed 0”
: Released
Menu_D
Note On/Note
Off
42
Button-Toggling
Output
“127” : Pressed 0”
: Released
Files
Note On/Note
Off
43
Button-Toggling
Output
“127” : Pressed 0”
: Released
Folders
Note On/Note
Off
44
Button-Toggling
Output
“127” : Pressed 0”
: Released
Scratch
Note On/Note
Off
45
Button-Toggling
Output
“127” : Pressed 0”
: Released
Automix
Note On/Note
Off
46
Button-Toggling
Output
“127” : Pressed 0”
: Released
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual 25/32
JOG_DA
Control Change
48
Incremental
Coarse (128
values)
127 > 64 : CCW
Slow > Fast
1 > 63 : CW
Slow > Fast
JOG_DB
Control Change
49
Incremental
Coarse (128
values)
127 > 64 : CCW
Slow > Fast
1 > 63 : CW
Slow > Fast
PITCH_DA
Control Change
50
Incremental
Coarse (128
values)
127 > 64 : CCW
Slow > Fast
1 > 63 : CW
Slow > Fast
PITCH_DB
Control Change
51
Incremental
Coarse (128
values)
127 > 64 : CCW
Slow > Fast
1 > 63 : CW
Slow > Fast
VOL_DA
Control Change
52
Analog Coarse
(128 values)
0 > 127 : Full Down
> Full Up
TREBLE_DA
Control Change
53
Analog Coarse
(128 values)
0 > 127 : Full CW :
Full CCW
MEDIUM_DA
Control Change
54
Analog Coarse
(128 values)
0 > 127 : Full CW :
Full CCW
BASS_DA
Control Change
55
Analog Coarse
(128 values)
0 > 127 : Full CW :
Full CCW
XFADER
Control Change
56
Analog Coarse
(128 values)
0 > 127 : Full Left >
Full Right
VOL_DB
Control Change
57
Analog Coarse
(128 values)
0 > 127 : Full Down
> Full Up
TREBLE_DB
Control Change
58
Analog Coarse
(128 values)
0 > 127 : Full CW :
Full CCW
MEDIUM_DB
Control Change
59
Analog Coarse
(128 values)
0 > 127 : Full CW :
Full CCW
BASS_DB
Control Change
60
Analog Coarse
(128 values)
0 > 127 : Full CW :
Full CCW
26/32User Manual
Control
MIDI output
Midi Control
Type
Midi
Command
(decimal)
Command Type
Midi Values
(decimal)
K1_DA
Note On/Note
Off
1
LED Toggling
Input
0 : OFF 127: ON
K2_DA
Note On/Note
Off
2
LED Toggling
Input
0 : OFF 127: ON
K3_DA
Note On/Note
Off
3
LED Toggling
Input
0 : OFF 127: ON
K4_DA
Note On/Note
Off
4
LED Toggling
Input
0 : OFF 127: ON
SHIFTED_K1_DA
Note On/Note
Off
5
LED Toggling
Input
0 : OFF 127: ON
SHIFTED_K2_DA
Note On/Note
Off
6
LED Toggling
Input
0 : OFF 127: ON
SHIFTED_K3_DA
Note On/Note
Off
7
LED Toggling
Input
0 : OFF 127: ON
SHIFTED_K4_DA
Note On/Note
Off
8
LED Toggling
Input
0 : OFF 127: ON
PBM_DA
Note On/Note
Off
10
LED Toggling
Input
0 : OFF 127: ON
PBP_DA
Note On/Note
Off
11
LED Toggling
Input
0 : OFF 127: ON
Cue_DA
Note On/Note
Off
14
LED Toggling
Input
0 : OFF 127: ON
Play_DA
Note On/Note
Off
15
LED Toggling
Input
0 : OFF 127: ON
Listen_DA
Note On/Note
Off
16
LED Toggling
Input
0 : OFF 127: ON
Sync_DA
Note On/Note
Off
18
LED Toggling
Input
0 : OFF 127: ON
MTempo_DA
Note On/Note
Off
19
LED Toggling
Input
0 : OFF 127: ON
K1_DB
Note On/Note
Off
21
LED Toggling
Input
0 : OFF 127: ON
K2_DB
Note On/Note
Off
22
LED Toggling
Input
0 : OFF 127: ON
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual 27/32
K3_DB
Note On/Note
Off
23
LED Toggling
Input
0 : OFF 127: ON
K4_DB
Note On/Note
Off
24
LED Toggling
Input
0 : OFF 127: ON
SHIFTED_K1_DB
Note On/Note
Off
25
LED Toggling
Input
0 : OFF 127: ON
SHIFTED_K2_DB
Note On/Note
Off
26
LED Toggling
Input
0 : OFF 127: ON
SHIFTED_K3_DB
Note On/Note
Off
27
LED Toggling
Input
0 : OFF 127: ON
SHIFTED_K4_DB
Note On/Note
Off
28
LED Toggling
Input
0 : OFF 127: ON
PBM_DB
Note On/Note
Off
30
LED Toggling
Input
0 : OFF 127: ON
PBP_DB
Note On/Note
Off
31
LED Toggling
Input
0 : OFF 127: ON
Cue_DB
Note On/Note
Off
34
LED Toggling
Input
0 : OFF 127: ON
Play_DB
Note On/Note
Off
35
LED Toggling
Input
0 : OFF 127: ON
Listen_DB
Note On/Note
Off
36
LED Toggling
Input
0 : OFF 127: ON
Sync_DB
Note On/Note
Off
38
LED Toggling
Input
0 : OFF 127: ON
MTempo_DB
Note On/Note
Off
39
LED Toggling
Input
0 : OFF 127: ON
Files
Note On/Note
Off
43
LED Toggling
Input
0 : OFF 127: ON
Folders
Note On/Note
Off
44
LED Toggling
Input
0 : OFF 127: ON
Scratch
Note On/Note
Off
45
LED Toggling
Input
0 : OFF 127: ON
Automix
Note On/Note
Off
46
LED Toggling
Input
0 : OFF 127: ON
Blink_K1_DA
Note On/Note
Off
49
LED Toggling
Input
0 : OFF 127: ON
Blink_K2_DA
Note On/Note
Off
50
LED Toggling
Input
0 : OFF 127: ON
28/32User Manual
Blink_K3_DA
Note On/Note
Off
51
LED Toggling
Input
0 : OFF 127: ON
Blink_K4_DA
Note On/Note
Off
52
LED Toggling
Input
0 : OFF 127: ON
Blink_SHIFTED_K1_DA
Note On/Note
Off
53
LED Toggling
Input
0 : OFF 127: ON
Blink_SHIFTED_K2_DA
Note On/Note
Off
54
LED Toggling
Input
0 : OFF 127: ON
Blink_SHIFTED_K3_DA
Note On/Note
Off
55
LED Toggling
Input
0 : OFF 127: ON
Blink_SHIFTED_K4_DA
Note On/Note
Off
56
LED Toggling
Input
0 : OFF 127: ON
Blink_PBM_DA
Note On/Note
Off
58
LED Toggling
Input
0 : OFF 127: ON
Blink_PBP_DA
Note On/Note
Off
59
LED Toggling
Input
0 : OFF 127: ON
Blink_Cue_DA
Note On/Note
Off
62
LED Toggling
Input
0 : OFF 127: ON
Blink_Play_DA
Note On/Note
Off
63
LED Toggling
Input
0 : OFF 127: ON
Blink_Listen_DA
Note On/Note
Off
64
LED Toggling
Input
0 : OFF 127: ON
Blink_Sync_DA
Note On/Note
Off
66
LED Toggling
Input
0 : OFF 127: ON
Blink_MTempo_DA
Note On/Note
Off
67
LED Toggling
Input
0 : OFF 127: ON
Blink_K1_DB
Note On/Note
Off
69
LED Toggling
Input
0 : OFF 127: ON
Blink_K2_DB
Note On/Note
Off
70
LED Toggling
Input
0 : OFF 127: ON
Blink_K3_DB
Note On/Note
Off
71
LED Toggling
Input
0 : OFF 127: ON
Blink_K4_DB
Note On/Note
Off
72
LED Toggling
Input
0 : OFF 127: ON
Blink_SHIFTED_K1_DB
Note On/Note
Off
73
LED Toggling
Input
0 : OFF 127: ON
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual 29/32
Blink_SHIFTED_K2_DB
Note On/Note
Off
74
LED Toggling
Input
0 : OFF 127: ON
Blink_SHIFTED_K3_DB
Note On/Note
Off
75
LED Toggling
Input
0 : OFF 127: ON
Blink_SHIFTED_K4_DB
Note On/Note
Off
76
LED Toggling
Input
0 : OFF 127: ON
Blink_PBM_DB
Note On/Note
Off
78
LED Toggling
Input
0 : OFF 127: ON
Blink_PBP_DB
Note On/Note
Off
79
LED Toggling
Input
0 : OFF 127: ON
Blink_Cue_DB
Note On/Note
Off
82
LED Toggling
Input
0 : OFF 127: ON
Blink_Play_DB
Note On/Note
Off
83
LED Toggling
Input
0 : OFF 127: ON
Blink_Listen_DB
Note On/Note
Off
84
LED Toggling
Input
0 : OFF 127: ON
Blink_Sync_DB
Note On/Note
Off
86
LED Toggling
Input
0 : OFF 127: ON
Blink_MTempo_DB
Note On/Note
Off
87
LED Toggling
Input
0 : OFF 127: ON
Blink_Files
Note On/Note
Off
91
LED Toggling
Input
0 : OFF 127: ON
Blink_Folders
Note On/Note
Off
92
LED Toggling
Input
0 : OFF 127: ON
Blink_Scratch
Note On/Note
Off
93
LED Toggling
Input
0 : OFF 127: ON
Blink_Automix
Note On/Note
Off
94
LED Toggling
Input
0 : OFF 127: ON
Update_All_Controls
Control Change
127
Control Input
0 : OFF 127: ON
7. FAQ
1. Can I use DJ Control MP3 e2 with DJ software other than the bundle included in the
package?
Yes: since your DJ Control MP3 e2 functions as a MIDI controller and can send MIDI
commands, it can be used with any software that accepts MIDI commands. Please see
section
6. Configuration in MIDI mode.
30/32User Manual
2. Can I use DJ Control MP3 e2 without a computer?
No, DJ Control MP3 e2 cannot function at all without being connected to a computer.
3. Can I mix directly from audio CDs in the DJ mixing software?
Yes, you can mix audio CDs directly from your CD/DVD-ROM drive in VirtualDJ. Simply load
the CD-Audio track in your playlist on a DJ Control MP3 e2 deck, as if it were an audio file, and
you can mix it immediately.
4. Will DJ Control MP3 e2 function when connected to a USB hub?
Yes, as long as the USB hub’s power supply is connected.
5. Can I save the DJ mixes I create with DJ Control MP3 e2 in an audio file?
Yes, you can save your mix by clicking the REC button in VirtualDJ.
6. Why doesn’t DJ Control MP3 e2 have a standard 1U rack format?
DJ Control MP3 e2 has been designed for the consumer market, and most home users do not
have access to a 1U rack.
8. TECHNICAL SUPPORT
If you encounter a problem with your product, please go to http://ts.hercules.com and select your language. From there you will be able
to access various utilities (Frequently Asked Questions (FAQ), the latest versions of drivers and software) that may help to resolve your
problem. If the problem persists, you can contact the Hercules products technical support service (“Technical Support”):
In order to take advantage of technical support by email, you must first register online. The information you provide will help the agents
to resolve your problem more quickly.
By email:
Click Registration on the left-hand side of the Technical Support page and follow the on-screen instructions.
If you have already registered, fill in the Username and Password fields and then click Login.
United Kingdom
By telephone (if you do not have Internet access):
08450800942
Charged at local rate
Monday to Saturday from 8 a.m. to 7 p.m.
United States
1-866-889-5036
Free
Monday to Friday from 9 a.m. to 8 p.m.
Saturday from 8 a.m. to 2 p.m.
(Eastern Standard Time)
Monday to Friday from 6 a.m. to 5 p.m.
Saturday from 5 a.m. to 11 a.m.
(Pacific Standard Time)
Canada
1-866-889-2181
Free
Monday to Friday from 9 a.m. to 8 p.m.
Saturday from 8 a.m. to 2 p.m.
(Eastern Standard Time)
Monday to Friday from 6 a.m. to 5 p.m.
Saturday from 5 a.m. to 11 a.m.
(Pacific Standard Time)
Denmark
80887690
Free
Monday to Saturday from 9 a.m. to 8 p.m.
(English)
Sweden
0200884567
Free
Monday to Saturday from 9 a.m. to 8 p.m.
(English)
Finland
0800 913060
Free
Monday to Saturday from 10 a.m. to 9 p.m.
(English)
Hours of operation and telephone numbers are subject to change. Please visit http://ts.hercules.com for the most up-to-date
Technical Support contact information.
ITALIANO
DEUTSCH
ESPAÑOL
NEDERLANDS
ENGLISH
FRANÇAIS
User Manual 31/32
8.1. Warranty information
Worldwide, Guillemot Corporation S.A. (“Guillemot”) warrants to the consumer that this Hercules product will be free from material
defects and manufacturing flaws for a period of two (2) years from the original date of purchase. Should the product appear to be
defective during the warranty period, immediately contact Technical Support, who will indicate the procedure to follow. If the defect is
confirmed, the product must be returned to its place of purchase (or any other location indicated by Technical Support).
Within the context of this warranty, the consumer’s defective product will, at Technical Support’s option, be either repaired or replaced.
Where authorized by applicable law, the full liability of Guillemot and its subsidiaries (including for indirect damages) is limited to the
repair or replacement of the Hercules product. The consumer’s legal rights with respect to legislation applicable to the sale of
consumer goods are not affected by this warranty.
This warranty shall not apply: (1) if the product has been modified, opened, altered, or has suffered damage as a result of inappropriate
or abusive use, negligence, an accident, normal wear, or any other cause not related to a material defect or manufacturing flaw; (2) in
the event of failure to comply with the instructions provided by Technical Support; (3) to software not published by Guillemot, said
software being subject to a specific warranty provided by its publisher.
8.2. Additional warranty provisions
In the United States of America and in Canada, this warranty is limited to the product’s internal mechanism and external housing. Any
applicable implied warranties, including warranties of merchantability and fitness for a particular purpose, are hereby limited to two (2)
years from the date of purchase and are subject to the conditions set forth in this limited warranty. In no event shall Guillemot
Corporation S.A. or its affiliates be liable for consequential or incidental damage resulting from the breach of any express or implied
warranties. Some States/Provinces do not allow limitation on how long an implied warranty lasts or exclusion or limitation of
incidental/consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you
may also have other legal rights which vary from State to State or Province to Province.
Trademarks
Hercules® is a registered trademark of Guillemot Corporation S.A. Intel® and Pentium® are registered trademarks of Intel Corporation.
Microsoft® Windows® 98 SE, Me, 2000, XP, Vista and 7 are either registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries. VirtualDJ™ is a trademark of Atomix Productions. All other trademarks and brand names are hereby acknowledged
and are property of their respective owners. Illustrations not binding. Contents, designs and specifications are subject to change without notice
and may vary from one country to another.
Declaration of conformity
EC COMPLIANCE NOTICE: Guillemot Corporation S.A. hereby declares that the device complies with the main requirements and other relevant
clauses of Directive CEM 2004/108/CE. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
CANADIAN COMPLIANCE NOTICE: this Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
USA COMPLIANCE NOTICE
(1) This device may not cause harmful interference, and
: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC rules. Operation is subject to the following two conditions:
(2) This device must accept any interference received, including interference that may cause undesired operation.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
In the event of malfunction during use due to electrostatic emission, you should exit the software, disconnect the device from the
computer, then resume normal use by reconnecting the device to the computer, and restarting the software.
Copyright
© 2010 Guillemot Corporation S.A. All rights reserved.
This publication may not be reproduced in whole or in part, summarized, transmitted, transcribed, stored in a retrieval system, or translated into
any language or computer language, in any form or by any means, electronic, mechanical, magnetic, photocopying, recording, manual or
otherwise, without the prior written permission of Guillemot Corporation S.A.
Disclaimer
Guillemot Corporation S.A. reserves the right to make changes to specifications at any time and without notice. The information provided by this
document is believed to be accurate and reliable. However, no responsibility is assumed by Guillemot Corporation S.A. either for its use or for the
infringement of patents or other rights of third parties resulting from its use. This product may exist in a light or special version for PC integration or
other purposes. Certain functions detailed in this manual may not be available in these versions. Wherever possible, a README.TXT will be
included on the installation CD-ROM detailing the differences between the supplied product and the product described in the present
documentation.
32/32User Manual
End-user software license Agreement for Hercules software
IMPORTANT
The Guillemot Corporation S.A. Software (hereafter named the “Software”) is copyrighted by Guillemot Corporation S.A. All rights are reserved.
The term “Software” refers to all documentation and related material, including drivers, executable programs, libraries and data files. The
purchaser is granted a license to use the Software only. The licensee also agrees to be bound by the terms and conditions of the present
Agreement concerning copyright and all other proprietary rights for any third party Software, documentation and related material included in the
Software package.
: please read the Agreement carefully prior to opening and installing the Software. By opening the Software package, you agree to
be bound by the terms of this Agreement. The Software enclosed in this package is licensed, not sold, and is only available under the terms of the
present license Agreement. If you do not agree with the terms hereafter, you must promptly return the Software within 15 days, together with the
entire contents of the box, to the place of purchase.
Guillemot Corporation S.A. reserves the right to terminate this license in the event of failure to comply with any of the terms or
conditions laid out in the present Agreement. On termination, all copies of the Software shall immediately be returned to Guillemot
Corporation S.A.; the purchaser remaining liable for any and all resulting damages.
License:
1. The license is granted to the original purchaser only. Guillemot Corporation S.A. retains all title to and ownership of the Software and reserves
all rights not expressly granted. The licensee is not permitted to sub-license or lease any of the rights that are hereby granted. Transfer of the
license is permitted, provided that the transferor does not retain any part or copy of the Software and the transferee accepts to be bound by the
terms and conditions of the present Agreement.
2. The licensee may only use the Software on a single computer at any time. The machine-readable portion of the Software may be transferred to
another computer provided it is previously erased from the first machine and there is no possibility that the Software can be used on more than
one machine at any one time.
3. The licensee acknowledges the copyright protection belonging to Guillemot Corporation S.A. The copyright notice must not be removed from
the Software, nor from any copy thereof, nor from any documentation, written or electronic, accompanying the Software.
4. The licensee is granted the right to make one back-up copy of the machine-readable portion of the Software on the condition that all copyright
and proprietary notices are also reproduced.
5. Except where the present Agreement expressly permits, the licensee is strictly prohibited from engaging in, nor may he permit third parties to
engage in, the following: providing or disclosing the Software to third parties; providing use of the Software in a network, multiple PCs, multi-
user or time-sharing arrangement where the users are not individual licensees; making alterations or copies of any kind of the Software; making
any attempt to disassemble, de-compile or reverse engineer the Software in any way or form, or engaging in any activity aimed at obtaining
underlying information not visible to the user during normal use of the Software; making copies or translations of the User Manual.
End-user software license Agreement for VirtualDJ Software
Please carefully read the License contract displayed when installing the VirtualDJ software. Afterwards, you can view the text
file installed on your computer at any time.
ENVIRONMENTAL PROTECTION RECOMMENDATION
At the end of its working life, this product should not be disposed of with standard household waste, but
rather dropped off at a collection point for the disposal of Waste Electrical and Electronic Equipment
(WEEE) for recycling.
This is confirmed by the symbol found on the product, user manual or packaging.
Depending on their characteristics, the materials may be recycled. Through recycling and other forms of
processing Waste Electrical and Electronic Equipment, you can make a significant contribution towards
helping to protect the environment.
Please contact your local authorities for information on the collection point nearest you.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Hercules-DJ-Control-MP3-E2

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hercules DJ Control MP3 E2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hercules DJ Control MP3 E2 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Hercules DJ Control MP3 E2

Hercules DJ Control MP3 E2 Gebruiksaanwijzing - Nederlands - 32 pagina's

Hercules DJ Control MP3 E2 Gebruiksaanwijzing - Deutsch - 32 pagina's

Hercules DJ Control MP3 E2 Gebruiksaanwijzing - Français - 32 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info