Handleiding Hendi 222973 (pagina 9 van 30) (Nederlands, Duits, Engels, Frans, Italiaans, Deens, Zweeds, Noors)

741077

Verklein

Vergroot

Pagina terug

1/30

Pagina verder

It can be disconnected by making the plug accessible or by in-

corporating a switch in the fixed wiring that meets electrical ins-

tallation standards.

The appliance must be permanently connected with wiring for

fixed installation.

(2- or 3-core cable with a minimum cross-section of 1 mm2 and

maximum of 1.5 mm2).

To complete the electrical connection, follow the wiring diagram

depending on the model that you wish to connect (see fig. 3A,

3B, 4A, 4B).

No earthing connection is required, given that this is a doubly-

insulated appliance (Class II).

Remove the connection cover as shown in fig. 2.

Perforate the flex holder (O) to allow the power supply wires to

pass through.

The power supply cable must be placed so that no liquid or va-

pour can enter the appliance along it. If this were not possible, the

cable entry should be sealed additionally,

e.g. with silicone. Otherwise, the indicated IP rating would not

be maintained.

This appliance has a one, two or three-speed motor (depending

on the model)

If you wish to install a commutator that lets you choose between

high speed (S3), medium speed (S2) (only in the Duct in Line

200/910 model) and slow speed (S1), see fig. 3A - 3B.

The timer is factory set only for high speed (S2).

If you wish, you can set the timer for low speed (S1) leaving the

high speed (S2) without a timer

• Connect the cable corresponding to the speed that you wish

to time to the Motor Line terminal on the electronic Timer panel.

• Connect the cable corresponding to the other speed to the gene-

ral power strip (TB) for operation without the timer.

Available versions:

• STANDARD. Does not require setting

• TIMER. Adjustable timer from 3’ to 15’.

In the event that this appliance is not used, it is recommended

that you disconnect it from the mains electricity supply.

SETTINGS AND OPERATION:

Perform the necessary settings according to the model installed.

TIMER (see fig. 4A - 4B)

To set the timer, turn the TIMER pin clockwise to increase the

time (3’- 15’).

The extractor fan will start, activated by the switch. When the

switch is deactivated,

the fan continues working for the set time and then turns off.

To finish the installation, verify that all the connections have been

done correctly

and make sure that the cables are placed correctly.

Place the connection cover in the correct position again and en-

sure that it cannot be removed without using a tool.

Make sure that the blades turn freely.

CLEANING AND MAINTENANCE:

• Before cleaning make sure that the appliance is not connected

to the electric network

and prevent it from being reconnected by accident.

• Clean with a damp cloth regularly.

• For maintenance operations

• The casing assembly must be removed from its position (see

fig. 2)

• Remove the two reducer pipes (V): Loosen the screws on the re-

ducer pipes, turn each reducer pipe about 9º in an anti-clockwise

direction and remove the pipe by pulling it (see fig. 5).

• The motor, propeller and all components should be inspected

periodically to ensure that they are not dirty and have not suffe-

red any damage. The frequency of inspections depends on the

appliance’s operating conditions.

• Remove the dirt on the propeller and the inner parts of the ca-

sing to avoid imbalances during operation, a decrease in aerody-

namic performance and motor damage.

• Motor bearings do not need maintenance.

• Once maintenance is complete, refit the reducer pipes and ca-

sing assembly.

Always demand original spare parts for repairs.

THE MANUFACTURER reserves the right to make any tech-

nological improvement or modification without prior notifi-

cation.

The symbol on the product or on its packaging indicates that

this product may not be treated as household waste. Instead it

shall be handed over to the applicable collection point for the re-

cycling of electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent potential

negative consequences for the environment and human health,

which could otherwise be caused by inappropriate waste handling

of this product. For more detailed information about recycling of

this product, please contact your local city office, your household

waste disposal service or the shop where you purchased the pro-

duct.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Hendi 222973 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info