535958
7
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
HECO VICTA PRIME 702, 602, 502, 302 – BI-WIRING AND BI-AMPING
Bi-wiring means using separate cables to carry the high and low audio frequencies. Bi-amping takes this
idea one step further and uses separate power amplifiers as well as separate cables for high and low
frequencies. Bi-amping in particular produces an additional improvement in sound reproduction quality.
The special connection terminals of the VICTA PRIME loudspeakers support both conventional connection
and operation in bi-wiring and bi-amping modes. There are four screw terminals on each speaker. The
top pair are for the tweeter (high frequencies), the lower pair for the woofer (low frequencies). The
factory-installed metal strips connecting the positive and negative terminals are for conventional 2-wire
connection and must be removed for bi-wiring and bi-amping operation. The pictures below show the
correct set-up for conventional operation (Fig. 4a), bi-wiring (Fig. 4b) and bi-amping (Fig. 4c).
HECO VICTA PRIME CENTER 102
The VICTA PRIME CENTER 102 loudspeaker visually and acoustically ideally matches the other VICTA
PRIME models. The loudspeaker is placed immediately underneath the television set. Otherwise please
adhere to the general recommendations outlined in the previous chapters.
HECO VICTA PRIME SUB 252 A
The VICTA PRIME SUB 252 A active subwoofer visually and acoustically ideally matches the other
loudspeakers in the Vica series. Please refer to the separate operating instructions supplied with this
product.
CONNECTING TO AN AV RECEIVER
Figs. 5 and 6 show two different methods of connecting to AV receivers.
Fig. 5: AV receiver without subwoofer output.
Fig. 6: AV receiver with subwoofer output.
HOW TO AVOID DAMAGE TO YOUR VALUABLE SPEAKERS
All HECO loudspeakers are designed and built for optimum sound reproduction with the tone controls
in the central position – i.e. with “linear” amplifier output. Turning up the bass and treble controls too far
delivers more power to the woofers and/or tweeters, and at high volumes this can actually destroy the
speaker units!
If the output of your amplifier is significantly higher than the rated power handling capacity of your
speakers extremely high volumes can physically destroy your speakers. This doesn’t actually happen
often but you should be aware that it is possible.
Weak amplifiers with low output ratings can actually be more dangerous for your speakers at medium
volumes because weak amplifiers may overload much faster than powerful ones and this causes
measurable and audible distortion, which is extremely dangerous to your loudspeakers.
Always turn the volume down immediately as soon as you hear distortion! If you like listening to loud music
make sure that your amplifier can deliver at least as much power as the speakers’ power-handling rating.
THE SOUND YOU CAN’T HEAR...
Amplifiers, tuners and CD players can all produce inaudible high-frequency signals – and this doesn’t
only apply to cheap products. If your tweeters fail at low or medium volumes you should have a qualified
technician check your system components for dangerous inaudible signals.
7
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Heco VICTA PRIME 502 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Heco VICTA PRIME 502 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds als bijlage per email.

De handleiding is 1,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info