535966
10
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
Mains connection (1), mains-voltage switch (2)
The subwoofer is equipped with an integrated amplifier and needs to be connected to a mains outlet by
means of the supplied mains cable. The voltage selector has been set at the factory to 230 V for opera-
tion in Europe.
Warning: Connecting the subwoofer to a 230 V mains outlet while the voltage selector is set to 115 V
will lead to immediate destruction of the amplifier!
Power switch (3), operating state LED (4)
Power switch ON Power switch OFF
The automatic switching on/off is activated.
The subwoofer switches on automatically when it receives a signal
from the receiver, the LED turns green.
It automatically switches to standby after receiving no signals for
some minutes, the LED turns red.
In standby mode the power consumption is 0.5 watt.
The subwoofer is switched off,
LED is off.
This is the setting for when
subwoofer isn‘t used over long
periods.
AV input (5)
Connect your receiver‘s low-level subwoofer output (sub-pre-out) to the subwoofer‘s AV input (see Fig.
3). You will require a mono-cinch cable for this (not supplied).
High-level inputs (6)
For connection to the high-level (speaker) outputs of the receiver/amplifier, refer to Fig. 2.
Level control (7)
This control is used to set the bass volume according to your preferences. Proceed as follows::
1. Set the bass control of your amplifier into its centre (linear) position.
2. Important: Set the level control to its left stop (lowest volume).
3. Now, play back some music and set the volume control of the amplifier to the desired level.
4. Set the subwoofer level control to the desired bass level.
Cross-over frequency control (8)
Used to set the upper limit of the subwoofer operating range. In combination with your HECO AMBIENT
satellites, this control should be set to 120 - 150 Hz.
The cross-over frequency control should be set to the maximum value (200 Hz) when AV receivers/
amplifiers are used. The cross-over frequency between the subwoofer and loudspeaker is then set in
the receiver’s/amplifier’s set-up. Please refer to your receiver’s/amplifier’s operating instructions here.
Phase switch (9)
In normal use the phase switch should be set to 0°. However, in rare cases it may be advantageous to
set the phase to 180° (e.g. if the subwoofer is far away from the front loudspeakers or in the event of
unfavourable acoustics in the room). Generally speaking: the setting where the lower base tone area
has a fuller sound is the correct one.
Fuse (10)
Only use a fuse with the parameters indicated next to the fuse holder, on the rear of the amplifier.
10
GB
10

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Heco-AMBIENT-5.1-A

Zoeken resetten

  • Mijn subwoofer doet het niet meer als ik hem aanzet gaat het stroom lampje even aan en gelijk weer uit het betreft een heco ambiant5.1a graag een reactie bvd Rob Gesteld op 27-2-2021 om 15:01

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Heco AMBIENT 5.1 A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Heco AMBIENT 5.1 A in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds als bijlage per email.

De handleiding is 1,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info