801904
13
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
13
4.154.14 4.16
Metering and control in ppm of
the free chlorine of the water.
Optional Free Chlorine control 4.14 Calibration of the Free Chlorine probe:
Recommended every month during usage season.
4.15 Calibration with buffer (photometer DPD1): Follow
the instructions in 6 steps that appear in the display.
4.16 Step 1 of 6 - Calibrate Cl at 0 ppm (offset): Close
the water flow through the probe and wait until the
reading is less than 0,10 ppm. Wait between 5 to 60
min. Press OK when the reading is close to 0.
4.184.17 4.19 4.17 Step 3 of 6 - Calibrate Cl: Open the water flow
until achieving 80-100 liters/hour. Wait until obtaining
a stable reading of ppm. Wait between 5 to 20 min.
Press OK when the reading is stable.
4.18 Step 5 of 6 - Establish the real ppm values
with the plus/minus keys according to your analysis
result of DPD1 (free chlorine).
4.19 Step 6 of 6 - If this screen is not shown repeat
the calibration process.
Free Chlorine probe
4.3 MEASURES / Free Chlorine calibration
4.20 4.21 4.21 Manual calibration: Open de water flow and
set the flowmeter (rotameter) at the right level of
flow (80-100l/h). Wait some minutes until the current
level is stable. With the plus/minus keys, insert
manually the water chlorine level (use a manual
DPD1 test kit). Press OK when the DPD1 value is
correct on display (target measurement).
5. FILTRATION / Manual mode
5.1 5.2 5.1 Filtration:
Configuration control of the filter pump. To set, select
Filtration and confirm by pressing OK . The mode
selection is done in Mode line with the plus/minus keys.
5.2 Manual:
Manually turns ON/OFF the filtration process. No timing
or additional functions. The State line indicates whether
the filtration pump is ON.
See section Filter Cleaning below.
110-230 V max. 3.15 A DRY CONTACT
FILTER PUMP
Filtration control
4.4 MEASURES / Conductivity calibration
4.23 4.244.22
Metering and control of
the conductivity of the
water in Msiemens.
Optional Conductivity probe 4.22 Calibration of the Conductivity probe:
Recommended every month during usage season.
4.23 Calibration with buffer (buffer solution 1413 µS/
12880 µS/ neutro): Follow the instructions in 7 steps
that appear in the display (screen 4.24 corresponds
to step 1).
4.25 4.26 4.25 Manual calibration: Allows to adjust the probes
at 1 point (without buffers) – only recommended to
adjust small deviation in the readings.
4.26 Without removing the probe from the water,
use the plus/minus keys to adjust the reading so it
matches with your reference value (photometer or
other measurement).
4.5 MEASURES / Temperature calibration
4.28 Temperature calibration: To set difference
between the measured value of the probe and the
actual temperature, use the plus/minus and up/down
keys. Set to the actual temperature of the probe and
press OK.
4.27 4.28
Temperature probe
necessary to activate
the filtration modes:
heating, intelligent,
smart.
Optional Temperature
Temperature
probe
Setup and connection of a Variable Speed
Pump, see section 13 - Variable Speed Pump
1
1
2
2
3
3
4
red black
3 4
4
5
6
7
8
Chlorine probe detector
FL2 (rotameter)
3
5
6
black
brown
blue
1
2
3
red
yellow
black
Conductivity probe
1 yellow
2 transparent
1 2 3 4 5 678910 11 12 13 14
7 & 8
14
12 11
A1 A2
LN
1
2
1 2 3
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hayward AquaRite UV LS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hayward AquaRite UV LS in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 6.81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info