801911
42
Verklein
Vergroot
Pagina terug
1/177
Pagina verder
18 / 20 AquaRite Pro Rev. C
TROUBLESHOOTING
Check System Indicator
The “CHECK SYSTEM” LED will alert you when the AquaRite Pro detects any of the follow-
ing conditions that are abnormal and require attention for optimal operation of your pool. Press
“<“ or “>” to view all of the existing “Check System” conditions.
Inspect Cell -- For optimum operation, you will need to inspect the AquaRite Pro chlorina-
tor cell approximately every 3 months and clean the cell if necessary. The AquaRite Pro will
automatically remind you when it is time and display “Inspect Cell, + to reset” as part of the
rotating Default Menu. Clean the cell (see instructions, page 12) and then press the “+” button
during the “Inspect Cell” display to reset the timer.
Low Salt/Minerals or Very Low Salt/Minerals -- When the salt is too low the AquaRite
Pro will generate less chlorine and the life of the cell is degraded. Check the cell and clean
if necessary before adding salt.
High Salt/Amps/Minerals -- The AquaRite Pro will stop generating chlorine under certain
high salt conditions in order to protect the internal electronics from damage. The only way to
lower the salt level is to partially drain the pool and add fresh water.
Chlorinator Cell Sensor -- The cell sensor is either an open or short circuit.
Low Volts -- If the chlorinator cell voltage is too low.
No Cell Power -- If no chlorinator cell power is detected on the printed circuit board.
Check Flow Switch
Cell Power Error -- If a chlorinator cell power error is detected on the printed circuit board.
Cell Missing -- If the chlorinator is enabled but no cell is detected.
CSM Comm Error: -- If Chemistry Sensing is enabled and the Chemistry Sense Module
(CSM) is not responding.
pH Probe Error -- If the CSM indicates that there is a problem with the pH probe.
pH Low - Check Feeder -- If a pH level of 6.9 or less is detected, check the feeder for proper
operation
pH High - Check Feeder -- If a pH level of 8.1 or higher is detected, check the chemical
supply and the feeder for proper operation
pH Timeout - Check Feeder -- If the unit has been dispensing for more than the selected
timeout without reaching the desired level. Check the chemical supply and the feeder. If
both are OK, the timeout may need to be increased. Press the “+” button to reset the alarm
and resume dispensing.
pH Calibration Error -- When using the pH Calibration Wizard and the entered test result
was different from the measured pH level by ± 1.0 or more. The pH probe may need to be
cleaned or replaced.
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hayward Aqua Rite Pro bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hayward Aqua Rite Pro in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 4.78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info