801892
22
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 5 of 16 AquaRite® Pro LS Rev. D
Si = pH + Ti + Ci + Ai - 12.1
°C °F Ti Calcium
Hardness Ci Total
Alkalinity Ai
12
16
19
24
29
34
39
53
60
66
76
84
94
100
0.3
0.4
0.5
0.6
0.7
0.8
0.9
75
100
125
150
200
250
300
400
600
800
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.4
2.5
75
100
125
150
200
250
300
400
600
800
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.8
2.9
How to use: Measure pool pH, temperature, calcium hardness, and
total alkalinity. Use the chart above to determine Ti, Ci and Ai into the
above equation. If Si equals 0.2 or more, scaling and staining may
occur. If Si equals -0.2 or less corrosion or irritation may occur.
{
- 0.2 0.20
OK
CORROSIVE SCALING
Salt Level
Use the chart on page 6 to determine how much salt in kgs need to be added to reach the recommended levels. Use the
equations below if pool size is unknown.
M³
(pool size in meters)
Rectangular Length x Width x
Average Depth
Round Diameter x Diameter x
Average Depth x 0.785
Oval Length x Width x
Average Depth x 0.893
The ideal salt level is between 1.2 - 2.5 g/L with 1.5 g/L being optimal. If the level is low, determine the number of M³ in
the pool and add salt according to the chart on page 6. A low salt level will reduce the efficiency of the AquaRite Pro LS
and result in low chlorine production. A high salt level can cause the AquaRite Pro LS to shutdown and may begin to give
a salty taste to your pool. The salt in your pool/spa is constantly recycled and the loss of salt throughout the swimming
season should be small. This loss is due primarily to the addition of water because of splashing, backwashing, or draining
(because of rain). Salt is not lost due to evaporation.
Type of Salt to Use
It is important to use only sodium chloride (NaCl) salt that is greater than 99% pure (EN 16401). Use only salt for
electronic chlorine generator usually available in 25 kg bags. Do not use rock salt, salt with yellow prussiate of soda, salt
with anti-caking additives, or iodized salt.
How to Add or Remove Salt
For new plaster pools, wait 10-14 days before adding salt to allow the plaster to cure. Turn the circulating pump on and
add salt directly into the pool. Brush the salt around to speed up the dissolving process. Do not allow salt to pile up on the
bottom of the pool. Run the filter pump for 24 hours with the suction coming from the main drain (use pool vac if there is
no main drain) to allow the salt to evenly disperse throughout the pool. The salt display may take 24 hours to respond to
the change in salt concentration.
The only way to lower the salt concentration is to partially drain the pool and refill with fresh water.
Always check stabilizer (cyanuric acid), when checking salt. These levels will most likely decline together. Use the
chart on page 6 to determine how much stabilizer must be added to raise the level to 25 ppm. Use stabilizer only if
necessary.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hayward Aqua Rite Pro LS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hayward Aqua Rite Pro LS in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 3.96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info