Verify Line Voltage Before Use
Festival has been designed for use with 120 volt
AC current. Connection to a line voltage other than
120 volts can create a safety and fire hazard, and
may damage the unit.
If you have any questions about the voltage
requirements for your specific model or about
the line voltage in your area, consult your selling
dealer
before plugging the unit into a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord
supplied with your unit. We do not recommend that
extension cords be used with this product.
As with all electrical devices, do not run power
cords under rugs or carpets or place heavy
objects on them. Damaged power cords should
be replaced immediately with cords meeting
factory specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC
outlet, always pull the plug,
never pull the cord
.
If you do not intend to use the unit for any
considerable length of time, disconnect the
plug from the AC outlet.
Do Not Open the Cabinet
There are no user serviceable components inside
this product. Opening the cabinet may present a
shock hazard, and any modification to the product
will void your warranty. If water or any metal object
such as a paper clip, a wire or a staple accidentally
falls inside the unit, disconnect it from the AC
power source immediately and consult an
authorized service station.
CATV or Antenna Grounding
If an outside antenna or a cable system is
connected to this product, be certain that it is
grounded to provide some protection against
voltage surges and static charges. Section 810 of
the National Electrical Code, ANSI/NFPA No. 70-
1984, provides information with respect to proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes and requirements of the
grounding electrode.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV (Cable
TV) system installer's attention to article 820-40
of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the
cable ground shall be connected to the grounding
system of the building, as close to the point of
cable entry as possible.
Installation Location
To assure proper operation and to avoid the
potential for safety hazards, place the unit on a
firm and level surface. When placing the unit on a
shelf, be certain that the shelf and any mounting
hardware can support the weight of the product.
Make certain that proper space is provided both
above and below the unit for ventilation. If this
product will be installed in a cabinet or other
enclosed area, make certain that there is sufficient
air movement within the cabinet. Under some
circumstances a fan may be required.
Do not place the unit directly on a carpeted surface.
Avoid installation in extremely hot or cold locations,
or an area that is exposed to direct sunlight or
heating equipment.
Avoid moist or humid locations.
Do not obstruct the ventilation slots on the top
of the unit, or place objects directly over them.
Cleaning
When the unit gets dirty, wipe it with a clean, soft,
dry cloth. If necessary, wipe it with a soft cloth
dampened with mild soapy water, and then a fresh
cloth with clean water.Wipe dry immediately with
a dry cloth. NEVER use benzene, aerosol cleaners,
thinner, alcohol or any other volatile cleaning agent.
Do not use abrasive cleaners, as they may damage
the finish. Avoid spraying insecticide near the unit.
Moving the Unit
Before moving the unit, be certain to disconnect
any interconnection cords with other components,
and make certain that you disconnect the unit from
the AC outlet.
Important Information for the User
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
The limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy
and, if installed and used in accordance with
the instructions, may cause harmful interference
to radio communication. However, there is no
guarantee that harmful interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by tuning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: 1) this device may not cause harmful
interference, and 2) this device must accept
interference received, including interference
that may cause undesired operation.
NOTE: Changes or modifications may cause this
unit to fail to comply with Part 15 of the FCC
Rules and may void the user’s authority to
operate the equipment.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
3
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU‘AU FOND.
