456579
18
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
BDS
18
Preparing the Remote Control
Preparing the Remote Control
Installing the Batteries
Your BDS system remote control uses 3 AAA batteries (supplied). Insert the batteries as
shown in the illustration, making sure to observe the correct polarity.
++
+
2
1
3
5
4
6
8
0
7
9
++
2
1
3
5
4
6
8
0
7
9
++
2
1
3
5
4
6
8
0
7
9
++
1. 2. 3.
Using the Remote
When using the remote, remember to aim it toward the receiver’s front panel. Make sure that
no objects, such as furniture, block the remote’s view of the receiver. Bright lights, fluorescent
lights, and plasma-video displays may interfere with the function of the remote.
The remote has a range of about 20 feet (6.1m), depending on the lighting conditions.
You can use the remote at an angle of up to 30° to either side of the
BDS receiver.
If the remote seems to operate intermittently, or if pressing a button on the remote does not
cause one of the buttons to light up, make sure that the batteries are inserted correctly. If the
remote still operates intermittently, replace all three batteries with new ones.
Programming the Remote
In addition to controlling the BDS receiver, you can program the remote to control one
auxiliary (Aux) component. The remote is also capable of learning codes directly from other
remotes. This ability allows you to combine learned commands with programmed codes,
making the remote capable of controlling more than one Aux component. Typical Aux
components would be your TV, a satellite receiver or a cable receiver.
The remote will control the Aux component(s) only when the Aux source button has been
pressed. Pressing any other source button will put the remote back into the BDS receiver
control mode.
To program the remote to control an Aux component:
Look up the codes for the product type (e.g. TV, cable TV box) and the brand name of your 1.
source in the Aux Component Remote-Control Code List, on page 31.
Turn your auxiliary component on.2.
Press and hold the Aux button for three seconds as it turns red, goes dark and turns 3. red
again. Then release the button.
NOTE: The remote will remain in the programming mode for 20 seconds. You must perform
Step 4 within 20 seconds.
Aim the remote toward the component you just turned on and enter a code number from 4.
Step 1, above. If the component turns off, check that its own remote-control buttons
control the component as expected. If they do, press the Aux button again to save the
code. The button will flash three times and the remote will exit the programming mode.
If any of the buttons do not work as expected, or if the device does not turn off when you 5.
enter the code number, repeat Step 4 with another code number from the list for that
manufacturer.
If you run out of codes, you can search through all of the codes in the remotes library for 6.
that product type.
Press and hold the Aux button for three seconds. The button will turn a) red, go dark
and turn red again. Then release the button.
For a conventional US TV, enter ”0999”; for a conventional EU TV, enter “1999”; for b)
an HDTV, enter “2999”; for a US cable box, enter “3999”; for an EU cable box, enter
“4999”; for a US satellite tuner, enter “5999”; for an EU satellite tuner, enter “6999.
Aim the remote control toward the component and press the remotes Cursor Up c)
button. Each press of the button sends the “Power” signal for one setup code number.
Holding down the Cursor Up button quickly scans through all of the setup code
numbers.
Release the Cursor Up button as soon as the component turns off. If you pass the d)
correct setup code number, you can return to it by pressing the Cursor Down button,
one setup code number at a time, until the component turns back on.
Check that the other remote-control buttons control the component as expected. If e)
they do, press the Aux source selector button again to save the code. The button will
flash three times, and the remote will exit the programming mode.
If the remote does not operate as expected, repeat Steps c – e. Note that some f)
components may not respond to all of the above commands and may support only
some of the commands listed.
To teach individual button codes to the remote:
You can teach codes from other component remotes onto the BDS receiver remote buttons
shown shaded in the following illustration:
DISC
AUX
iPOD
RAD IO
SET TI N GS
DIS PL AY
A - B
REPE A T
2
EJE C TSYST E MDEVI C E
1
3
5
4
6
8
0
7
9
CLE A R
HOM E
FIN D
OPT I ON S
SURR OU ND
OK
TO P ME NU
POP- UP
EXI T
++
VOLUME
CHAN NEL
MUT E
THUMB NAIL
ZOOM
BOO KMAR K
PROGRAM
= Learning Capable
Place the 1. BDS remote and the remote from which you want it to learn codes head-to-
head about 1 inch (2.5cm) apart, with their IR transmitter windows facing each other.
Press and hold the Settings button on the 2. BDS receiver remote for more than three
seconds. The remotes Aux button will light up.
Press the button on the 3. BDS receiver remote to which you want to teach the command.
The Learn mode will remain active for 20 seconds after the button is pushed.
Press the button on the other remote that you want to “teach” to the 4. BDS receiver remote.
When the IR code has been received and stored, the Aux buttons LED will flash three
times, and the BDS receiver remote will remain in the learning mode, ready to learn
another code. If no IR code is received within 20 seconds, the Aux LED will flash rapidly
several times, and the remote will exit the learning mode. To resume programming,
return to Step 2.
Repeat Step 3 and Step 4 for each command you want to teach the 5. BDS receiver remote.
NOTE: If the Aux button’s LED goes out at any time, you will need to begin again from
Step 2.
Programming Remote Control “Punch-Through” Commands
After programming the remote to control an auxiliary (Aux) component, you can also
program it so it will control the Aux component’s channel up/down and transport functions
(Play, Pause, etc.) even when the remote is not in the Aux-control mode. For example, if the
18

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Harman-Kardon-BDS-300

Zoeken resetten

  • Bij het uitzetten van de installatie gaat de sub woofer niet uit wat kan hiervan de oorzaak zijn
    vg Ron Gesteld op 27-7-2023 om 11:10

    Reageer op deze vraag Misbruik melden
  • Kan ik op kanaalnummers zoeken naar de radiostations? Gesteld op 7-12-2020 om 13:25

    Reageer op deze vraag Misbruik melden
  • Ik probeer het geluid van mijn tv (Sony) via een BDS275 op de bijbehorende geluidboxen te krijgen. Geluid van het radiosignaal gaat prima, maar het tv-geluid blijft dood. Verbinding tussen tv en BDS via HDMI en er zit ook een kabel voor optisch (geluid)signaal tussen tv en Humaxkastje (Ziggo). Op de tv staat aansturing via HDMI op 'uit'. Ik doe iets niet goed, maar ja, wat? Gesteld op 7-1-2018 om 10:59

    Reageer op deze vraag Misbruik melden
    • Ik stel de vraag opnieuw. Zat een foutje in de eerste vraag.
      Ik probeer het geluid van mijn tv (Sony) via een BDS275 op de bijbehorende geluidboxen te krijgen. Geluid van het radiosignaal gaat prima, maar het tv-geluid blijft dood. Verbinding tussen tv en BDS via HDMI en er zit ook een kabel voor optisch (geluid)signaal tussen BDS en Humaxkastje (Ziggo). Op de tv staat aansturing via HDMI op 'uit'. Ik doe iets niet goed, maar ja, wat? Geantwoord op 8-1-2018 om 06:37

      Waardeer dit antwoord (17) Misbruik melden
  • BDS 300 valt ineens uit tijdens afspelen dvd. Power led blijft zwak knipperen maar apparaat reageert verder nergens op. Iemand een idee?? Gesteld op 27-1-2016 om 21:52

    Reageer op deze vraag Misbruik melden
  • mijn kardon gaat over naar screen saver waardoor geluid niet meer doet Gesteld op 2-12-2015 om 22:23

    Reageer op deze vraag Misbruik melden
  • ik heb een samsung tv met een interactieve tv. Met het kijken naar een film op tv, of het kijken naar een dvd, luister ik het geluid af via het home cinema setje via de boxen.
    Nu is mijn vraag, als ik via mijn apple mac pro laptop, muziek wil luisteren van youtube, via mijn harmon cardon, wat zijn dan de beste opties. een chromecast of een apple tv. Hoe synchroniseer ik dat dan?
    groeten Flora Vos, emailadres is vosflora@gmail.com Gesteld op 24-11-2015 om 10:11

    Reageer op deze vraag Misbruik melden
    • Koop een Bluetooth setje van bv Philips. Hiermee kan je geluid van je Spotify afspelen op je Harman Kardon via Aux L1 Geantwoord op 30-1-2016 om 12:08

      Waardeer dit antwoord Misbruik melden
6
12
  • Krijg het toch niet voor elkaar maar toch bedankt voor het meedenken ! Geantwoord op 13-5-2015 om 20:05

    Waardeer dit antwoord (1) Misbruik melden
  • Hallo ook ik had problemen, maar opgelost. idd met de knop aux krijg je op je display verschillende opties, wel is het aan te raden dat er dan ook een optical aansluiting inzit. aangeven dat het optical 1 moet zijn. daarna op de tv ext luidspreken aanvinken. Geantwoord op 18-9-2015 om 17:33

    Waardeer dit antwoord Misbruik melden
  • Wanneer ik de tuner van de bds 330 aanzet, gaat ook de tv aan. Hoe stel ik in, zodat de tv niet aangaat? Gesteld op 22-11-2014 om 13:09

    Reageer op deze vraag Misbruik melden
  • als ik de bds 570 aansluit op de upc horizon box kan ik enkel audio afluisteren via installatie
    audio tv blijft uit,dus samengevat ben altijd verplicht bds aan te zetten anders geen audio en video signaal op tv ?????? Gesteld op 7-11-2014 om 20:47

    Reageer op deze vraag Misbruik melden
  • Harman kardon bds 300 speelt geen cd of deden meer af cd gaat er in en zegt reading disk en komt er gelijk weer uit Gesteld op 20-10-2014 om 07:08

    Reageer op deze vraag Misbruik melden
  • Heb hetzelfde problem is er een oplossing of is er een technisch problem? Geantwoord op 27-2-2015 om 17:16

    Waardeer dit antwoord Misbruik melden
  • Hier nog iemand met hetzelfde probleem,
    in het begin werkte alles naar behoren, nu 4 maanden later
    kapot, en als ik de reacties zie vind ik de prijs kwaliteit verhouding
    Belachelijk slecht!

    Eerste en de laatse Keer haka, over op Sonos Geantwoord op 11-3-2015 om 08:02

    Waardeer dit antwoord (3) Misbruik melden
  • Heeft iemand Netflix via BDS 300 werkend gekregen of is dit niet mogelijk Gesteld op 15-9-2014 om 23:00

    Reageer op deze vraag Misbruik melden
  • hallo ik wou even weten hoe je dat nu moet doen radio s zenders opzoeken en vastzetten hartelijk dank Gesteld op 9-4-2014 om 11:09

    Reageer op deze vraag Misbruik melden
    • Dit staat niet goed in de Nederlandse handleiding (met bookmark knop). De stappen die bij mij werkten (volgens de Engelse handleiding):
      1) Zoek met de pijltjes naar links/rechts de zender die je wilt opslaan
      2) Druk 2 seconden op OK
      3) Kies het kanaal waarop je de zender wilt opslaan (bv 01, 02, 11...)
      4) De zender is direct opgeslagen

      Ik heb gemerkt dat je kanaal 1 t/m 9 direct met de numerieke toetsen kan kiezen, daarboven moet je werken met Channel +. Dus zet onder 1 t/m 9 echt de meest gebruikte zenders. Geantwoord op 15-5-2015 om 11:58

      Waardeer dit antwoord (1) Misbruik melden
  • Kan ik geluid van tv aansluiten op HK BDS 300? Gesteld op 17-1-2014 om 12:28

    Reageer op deze vraag Misbruik melden
18
24
30

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Harman Kardon BDS 300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Harman Kardon BDS 300 in de taal/talen: Engels als bijlage per email.

De handleiding is 9,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Harman Kardon BDS 300

Harman Kardon BDS 300 Snelstart handleiding - Nederlands - 10 pagina's

Harman Kardon BDS 300 Gebruiksaanwijzing - Nederlands - 38 pagina's

Harman Kardon BDS 300 Snelstart handleiding - Deutsch - 10 pagina's

Harman Kardon BDS 300 Gebruiksaanwijzing - Deutsch - 38 pagina's

Harman Kardon BDS 300 Gebruiksaanwijzing - Français - 10 pagina's

Harman Kardon BDS 300 Gebruiksaanwijzing - Français - 38 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info