AVR85 120 rev (g) 6/14/97
Basic Operation
24
1. Tune to the desired preset station.
2. Press the Memo button ^rfor
more than three seconds.
3. Note that a character on the left side of
the main information display will start to
blink.
4. Enter the first character of the name
using either the front panel Tune ⁄
or ¤ buttons Ú or the alphanumeric
buttons x on the remote.
A. To use the front panel buttons simply
press and hold Tune ⁄ Ú button until
the desired letter or number appears.
Note that the upper case alphabet will
appear, followed by the numbers 1
through 0, and then a
indicating a
blank space. Tapping the button will
advance the display one character at
a time; holding it down will move the
display quickly. If you pass by the desired
character, use the Tune ¤ Ú to move
the display in reverse.
After entering the first character, press
Memo ^ to move to the next position
and note that the next digit will blink.
Use the same procedure outline above to
enter a character.
When you have entered a digit or
“blank” in all five spaces, press and hold
the Memo button ^ for a second to
confirm the entry
B. To use the remote for character entry,
press the button corresponding to the
desired letter or number. Press it once to
enter the first printed letter, twice for the
second, three times for the third and four
times for the number. Press the “9”
button to enter a blank space. (For
example, press the “ABC” button once
to enter an “A,” three times for a “C”
and four times to enter a “1”.)
Use the Memo button v to move to
the next digit position. When all five
spaces have been filled, press and hold
the Memo button again for a second to
confirm the entry.
Once a station name has been attached to
a preset position, the station’s frequency
will appear briefly when the unit is tuned
to that station. After a few seconds the
preset name will appear in the display.
Tuning Preset Stations
Stations preset into the tuner’s memory
may be recalled in a number of ways.
1. To recall a station directly enter a
number from 1 to 30 using the number
buttons on the remote x.
a. To enter a single digit memory
location, press 0 before the number,
or enter the number and wait a few
seconds.
b. If an invalid number (other than
1–30) is entered in error, that number
will flash to alert you that the entry is
invalid and the display will return to
the previous frequency display.
2. To scan through the list of preset
stations, press the P-Set⁄ or
P-Set ¤ button on the front panel Ô
or the Channel buttons u on the
remote.Press once to move up or down
thorough the memory presets one by one,
or press and hold the button to quickly
scan through the list of stations.
3. To automatically review each station
in the memory, press the P-Scan
button wÒ. Note that the P-Scan
indicator G will blink.
• The tuner will move up through the
list of stations, pausing to play each for
five seconds. Note that preset numbers
where no station has been pro-
grammed will be skipped.
• When the desired station is reached
press P-Scan Ò.
Clearing Preset Stations
Once stations are programmed into the
preset memories, it is possible to remove
them individually or as a group.
To remove a single station from the
memory:
1. Recall the station by pressing the
buttons on the remote corresponding to
the station’s memory location.
2. Press the Memo button ^ or v
and observe that the Memo indicator O
will blink.
3. While the indicator is blinking, press
the Clear button & within five seconds.
The word CLEAR will show briefly to
confirm that the memory position has
been cleared.
To clear all memory locations for the
tuner, as well as all volume level and sur-
round mode memories:
1. Press the Memo button v and the
Clear button x at the same time.
Note: When a complete memory clear
is performed the AVR85 will turn off and
then on as part of the process. After clear-
ing the memory it is necessary to reset all
stations and set up parameters.
AVR85 om (g) 9/16/98 11:21 AM Page 24
