Front Panel Controls
) DVD Input: Press this button to
select the source connected to the
DVD Input •. Note that if the DVD
or LV player’s digital audio output is
used, it must be selected separately
using the Digital Input Selectors
9g.
! Video Sources: Press any of
these buttons to select a video input
source.
@ Mode: Press these buttons to
scroll up ⁄ or down ¤ through the
list of available surround modes.
# Multiroom Control: Press the
button to turn the remote room feed
on or off. The Multi indicator D will
light or flash when the remote feed is
on. Note that the remote zone feed
will remain on after the main room
power is turned off until it is
switched off by pressing this button
again
$ OSD (On Screen Display): Press
the button briefly to display a system
status report on your video screen.
% ATT (Attenuation) Mode Select:
Press this button to activate the
Attenuation mode which cuts the
analog input signal by 50% to com-
pensate for high-level input sources.
^ Memo: The memo button is used
to enter stations to the tuner’s preset
memory in either the manual or
automatic modes.
& Clear: The clear button is used
to cancel tuning, memory input or
when clearing the unit’s memories.
* FM Mode: Press this button
to select the tuning mode for FM
stations.
( Bass: This knob adjusts the tone
of low-frequency sounds. Turn it to
the right to boost bass frequencies
or to the left to cut bass frequencies.
Ó Treble: This knob adjusts
the tone of high-frequency sounds.
Turn to it the right to boost high
frequencies or to the left to cut high
frequencies.
Ô P-Set: Press this button to manu-
ally scroll up ⁄ or down ¤ through
the FM or AM stations programmed
into the receiver’s preset memory.
Balance: This knob adjusts the
balance between the front left and
right speakers.
Ò P-Scan: Press this button to
automatically scan through the
FM or AM stations preset into the
receiver’s memory. Press the button
again to stop the scan when the
tuner is at the desired station.
Ú Tune: Press this button to manu-
ally scan up ⁄ or down ¤ through
the FM or AM bands.
Û Video 3 Input: Audio or Video
sources connected to these jacks
may be selected by pressing the
Video Source button !.
Ù Mute: Press this button to cut
the output to the speakers. Press
it again to return to the previous
volume level.
ı Volume Control: Turn the knob
clockwise to increase volume,
counterclockwise to decrease the
volume. Note that approximately two
revolutions of the knob are required
to go from no output to maximum
volume.
ˆ Information display: This
display delivers messages and
status indications to help you operate
the receiver. Refer to the separate
diagram for complete explanation of
the FL display.
˜ Remote Sensor Window: The
sensor behind this window receives
infrared signals from the remote con-
trol. Aim the remote at this area and
do not block or cover it unless an
external remote sensor is installed.
5
AVR85 120 rev (g) 6/14/97
1 Power: Press this button once to
turn the unit on and off. Once the
unit is turned on, it may be turned off
and then on again from the remote, if
desired.
Note: When the remote is used to
turn the unit off the LED surrounding
the Power Switch will turn amber,
indicating that the AVR85 is in a
Standby mode. In this condition the
unit is NOT disconnected from the
AC main power supply.
2 AM/FM Tuner Selector: Press
this button once to select the tuner.
Press it again to switch between AM
and FM.
3 Headphone Jack: Plug standard
stereo headphones into this jack for
private listening.
NOTE: When the headphones are in
use the output to the speakers is
muted and the surround mode is
automatically switched to STEREO.
When the headphones are removed
from the jack, sound to the speakers
is restored and the unit returns to the
previous sound mode.
4 CD: Press this button to select
the CD player.
5 Tape1/Monitor: Press this button
to select Tape One as the input
source. A red LED above the button
will illuminate to indicate that the
Tape Monitor has been selected.
6 Night Mode: Press this button to
activate the “Night” mode, prevent-
ing loud playback when the digital
modes are in use.
7 Tape2: Press this button to select
Tape 2 input.
8 TV Input: Press this button to
select the source connected to the
TV Input ª.
9 Digital Input Selectors: Press
one of these buttons to select a
digital input source. The digital
audio source may be the same as,
or different from, the analog audio of
the selected video source.
AVR85 om (g) 9/16/98 11:21 AM Page 5
