502638
52
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
52 CONFIGURING THE REMOTE
CONFIGURING THE REMOTE
Button o until the desired device name
appears to the right of the device in use. In our
example, that is the cable box. When the desired
combination of devices appears, press the Set
Button
q
.
Figure 62
6. When the Set button is pressed, the display will
change to show you that the new combination
of control commands is being saved to the unit’s
memory, as shown in Figure 63. The word
SAVED will flash four times and then the remote
will return to normal operation.
Figure 63
7. Once the punch-through is programmed, the
Channel Up/Down Buttons of the second
device named will be used when those buttons
Y
are pressed while the master device is
in use.
Returning the Channel Control Settings to
Default Operation
If you wish to remove the Channel Punch-Through
so that the commands for Channel Up/Down are
returned to the factory default setting, follow the steps
shown above, except that in Steps 4 and 5, select
the same device for both the DEVICE IN USE on
the left side of the bottom line and the PUNCH-
THROUGH device. In the example used, the display
to return the remote to default settings will appear as
shown in Figure 64.
Figure 64
Transport Punch-Through
The Play
Z
, Stop
J
, Fast Forward/Reverse
I
, Pause
J
, Record
J
and Skip Up/Down
K
Transport Controls are set at the factory to oper-
ate your DVD player, or the controls of a specific
device such as a VCR or CD player when they are
selected. However, by using the Transport Punch-
Through feature you may program these controls to
transmit the commands for a different device. For
example, you may wish to operate the transport of a
VCR connected to the VID 1/VCR input as the default,
rather than the button for a DVD player, as shown in
the following example.
1. Press and hold the Program Button
O
for
about three seconds while the message shown
in Figure 21 appears in the remote’s LCD
Information Display
2
. Release the button
when the red light under the Set Button
q
appears.
2. The remote’s MAIN MENU message (Figure
20) will appear in the LCD display and the Set
Button
q
will remain illuminated in red. Press
the
/
¤
Navigation Button o until
PUNCH-THROUGH appears on the bottom
line of the LCD screen, as shown in Figure 51.
Press the Set Button
q
to enter the main
punch-through menu branch.
3. At the next menu screen, press the
/
¤
Navigation Button o until TRANSPORT
appears on the bottom line of the LCD screen, as
shown in Figure 65. Press the Set Button
q
to begin programming the remote for transport
punch-through.
Figure 65
4. The next display screen (Figure 66) is where you
select the device that will receive the punch-
through commands. In our example, that is the
TV button, as that is where we want the VCR’s
transport controls to be active. Press the
/
¤
Navigation Button o until the name of the
base device appears and then press the Set
Button
q
.
Figure 66
5. At the next display screen (Figure 67), you will
select the device whose transport commands will
be used. Press the
/
¤
Navigation Button
o until the desired device name appears to the
right of the device in use. In our example, that is
the VCR. When the desired combination of
devices appears, press the Set Button
q
.
Figure 67
6. When the Set button is pressed, the display will
change to show you that the new combination of
control commands is being saved to the unit’s
memory, as shown in Figure 68. The word
SAVED will flash four times and then the remote
will return to normal operation.
Figure 68
7. Once the punch-through is programmed, the
transport buttons of the second device named
will be used when those buttons are pressed
while the master device is in use.
Returning the Transport Control Settings to
Default Operation
If you wish to remove the Transport Punch-Through so
that the transport commands are returned to the fac-
tory default setting, follow the steps shown above,
except that in Steps 4 and 5, select the same device
for both the DEVICE IN USE on the left side of the
bottom line and the PUNCH-THROUGH device. In
the example used, the display to return the remote to
default settings will appear as shown in Figure 69.
Figure 69
EzSet Configuration
Harman Kardon’s patented EzSet feature makes it easier
than ever to calibrate the output levels on your new
receiver for maximum playback accuracy. In addition
to automatically setting the levels, the AVR remote’s
LCD display allows the unit to be used as a direct
read-out SPL meter. Complete instructions for using
the EzSet features of the AVR remote are found on
pages 29–30 of this owner’s manual.
In most cases you will find it easier to access the
EzSet capabilities directly by pressing the SPL Select
Button i and following the menu prompts as
detailed on page 29. However, there is one function of
the remote that is available only through the remote’s
menu system being described in this section.
To avoid having the calibration settings created with
EzSet changed accidentally, the remote allows you to
disable the SPL Select Button j on the remote.
To de-activate the button, follow these steps:
1. Press and hold the Program Button
O
for
about three seconds while the message shown
in Figure 21 appears in the remote’s LCD
Information Display
2
. Release the button
when the red light under the Set Button
q
appears.
2.
The remote’s MAIN MENU message (Figure 22),
will appear in the LCD display and the Set Button
q
will remain illuminated in red. Press the
/
¤
Navigation Button o until SET SPKR
LEVELS appears on the bottom line of the LCD
screen, as shown in Figure 70. Press the Set
Button
q
to enter the main EzSet menu
branch.
Figure 70
MAIN MENU
SET SPKR LEVELS
PUNCH-THROUGH
TV< -TV
TV< -VCR [TRS]
SAVED
PUNCH-THROUGH
TV< -VCR
DEVICE IN USE
TV
PUNCH-THROUGH
TRANSPORT
PUNCH-THROUGH
VCR< -VCR
VCR< -CBL [CHAN]
SAVED
PUNCH-THROUGH
VCR< -CBL
AVR7300(120v)-OM 6/14/04 9:16 AM Page 52
52

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Harman Kardon AVR7300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Harman Kardon AVR7300 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info